SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4479-8
The von Neumann architecture is increasingly constrained by energy consumption and data-transfer efficiency as artificial intelligence and data-intensive applications expand. Neuromorphic computing, inspired by the human brain's information-processing mechanisms, offers an alternative paradigm. Two-dimensional (2D) ferroelectric materials are promising candidates due to their intrinsic non-volatility, atomic-scale thickness, ultra-low power consumption, excellent fatigue endurance, and dangling-bond-free surfaces. This review examines recent advances in 2D ferroelectric materials and associated device architectures for neuromorphic applications. It first introduces ferroelectric mechanisms and representative 2D ferroelectrics, then surveys key device architectures including ferroelectric tunnel junctions, diodes, transistors, and photovoltaic devices. Their applications in in-memory computing and in-sensor neuromorphic systems are discussed, with emphasis on artificial neural networks, spiking neural networks, reservoir computing, and neuromorphic perception for efficient information processing and intelligent sensing. The unique properties of 2D ferroelectrics enable integrated sensing, memory, and computing functionalities, demonstrating potential for future neuromorphic and brain-inspired intelligent systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3738-1
The escalating demand for intelligent and functional textiles, driven by technological advancements, has shifted focus from conventional attributes like warmth and aesthetics to smart functionalities. Natural biomass-derived polysaccharides, owing to their biocompatibility, biodegradability, renewability, and unique chemical structures, are pivotal for next-generation flexible wearable smart textiles. This review systematically outlines common natural polysaccharides (e.g., cellulose, chitosan, starch, alginate) used in such textiles, detailing their structural features and modification strategies. It critically evaluates current fabrication methods, highlighting their advantages and limitations. The performance characteristics, action mechanisms, and application scenarios of polysaccharide-based smart textiles are examined, with emphasis on healthcare, motion tracking, smart clothing, and energy storage/management. The review concludes by addressing existing challenges and proposing future directions for integrating polysaccharide materials into smart textile systems, aiming to guide the development of efficient, green flexible wearable devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3685-7
NiMo-based catalysts are promising for the hydrogen evolution reaction (HER), yet optimizing their electronic structure and enhancing mass transfer remain challenging. Here, we report a route to synthesize two-dimensional (2D) porous Mo2N-Ni heterojunction nanosheets with tuned Ni/Mo ratio for enhanced alkaline HER. The precursor is assembled from polyoxometalate clusters (PMo12) and layered Ni(OH)2. The interaction between PMo12 and Ni(OH)2 suppresses particle agglomeration during pyrolysis, yielding 2D porous sheets composed of small Mo2N-Ni units. Electron transfer from Ni to Mo2N redistributes electrons at the heterojunction, optimizing intermediate adsorption/desorption. The porous structure enhances mass transfer, reducing catalyst impedance. The optimized catalyst exhibits an overpotential of 19 mV at 10 mA cm−2, comparable to commercial Pt/C. An anion exchange membrane (AEM) electrolyzer pairing this catalyst with NiFe-LDH achieves 500 mA cm−2 at 1.80 V and operates stably for 300 h. This assembly method offers a scalable strategy for efficient catalyst production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3674-2
Enhancing catalytic activity is a core objective in catalyst design, with active site accessibility being a critical determinant. Polyoxometalate-based metal-organic complexes (POMOCs), combining advantages of POMs and MOCs, offer potential for constructing catalysts with highly accessible active sites. In this study, a series of POMOCs were synthesized using different POM templates: [CoII1.5(L)1.5(PMo12O40)(H2O)4]·3H2O (Co-PMo12), [CoII1.5(L)1.5(PW12O40)(H2O)4]·3H2O (Co-PW12), [CoII2(L)2(SiW12O40)(H2O)4]·11H2O (Co-SiW12), and H[CoII2.5(L)3(P2W18O62)(H2O)8]·10H2O (Co-P2W18). These were characterized by FT-IR, PXRD, and single-crystal X-ray diffraction. Catalytic activity differences for olefin epoxidation were attributed to distinct accessibility of Co(II) sites upon thermal activation. Notably, Co-P2W18 achieved 99% yield of 1,2-epoxycyclooctane within 3 hours at room temperature using O2 as oxidant, owing to highly accessible unsaturated Co(II) sites. This performance is superior to most reported catalysts. The reaction mechanism was investigated using density functional theory. The catalyst exhibited excellent stability over five cycles, with FT-IR, PXRD, and XPS confirming structural and oxidation state integrity. This work highlights the potential of POMOCs in designing catalysts with highly accessible active sites for enhanced catalytic activity.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507111
This study investigated the effects of a ring-shaped pulsed electric field (PEF) (1.5 V, 4 h on-time per cycle) on nitrogen removal performance and microbial community structure of anammox granular sludge (AnGS). Two anaerobic sequencing batch reactors (R1 control, R2 with PEF) were operated under stepwise increasing nitrogen loading rates (NLR). At NLR below 1,155 mg·(L·d)−1, R2 exhibited total nitrogen removal efficiency (TRE) 7.5%–17.0% higher than R1, with biomass, specific anammox activity (SAA), and extracellular polymeric substances (EPS) increased by 5%–7%, 21%–71%, and 54%–77%, respectively. However, at NLR above 1,320 mg·(L·d)−1, the toxic effect of nitrite dominated, and PEF enhancement diminished or even reversed to inhibition. Microbial community analysis revealed that at low-to-moderate NLR, PEF increased the relative abundance of Planctomycetes and key anammox bacteria (Candidatus Brocadia and Candidatus Jettenia), along with enhanced community richness (Chao1) and diversity (Shannon/Simpson indices). At high NLR, PEF decreased microbial richness compared to R1. Principal component analysis and redundancy analysis indicated that PEF was the key factor driving community differences at low-to-moderate NLR, whereas nitrite concentration became the dominant factor at high NLR. This study provides theoretical support for enhancing the resilience and engineering application of anammox processes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3470-6
Inkjet printing of two-dimensional transition metal chalcogenides (TMDs) is promising for low-cost, large-scale flexible electronics, yet challenges persist due to poor crystallinity and toxic solvents. Here, we report a green ink formulation using zwitterionic cocamidopropyl betaine (CAB) as a dispersant and surfactant for liquid-phase exfoliation of single-crystalline TMDs in water and isopropanol (IPA). The dispersions contain no additives or binders, enabling direct production of stable (over one month) and concentrated (2 mg/mL) inks for MoS2, MoTe2, WS2, WSe2, and WTe2. Fully-printed MoSe2/CAB humidity sensors exhibit superior sensitivity (ΔI/I0 = 468.1) and rapid response/recovery times (27 s/0.42 s) under bending. Inkjet-printed WTe2/CAB pads on 6-μm-thick substrates demonstrate exceptional mechanical stability, with resistance variations of 1.4% under single bending and 2% after 1,000 cycles, and acquire high-quality electrocardiogram (ECG) and electromyography (EMG) signals. This strategy enables scalable fabrication of TMD-based flexible electronics, advancing industrial integration.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61101-8
Phenolic compounds are typical refractory organic pollutants in coal chemical coking wastewater, posing significant risks to ecosystems and human health. Conventional treatment methods are inefficient, necessitating advanced oxidation processes (AOPs). Here, we report a low-cost Fe/N–C catalyst synthesized from coal-tar pitch, a common by-product of the coal chemical industry, via a self-assembly and pyrolysis strategy using graphitic carbon nitride (g-C3N4) as a template and nitrogen source, with dicyandiamide as an auxiliary nitrogen source and FeCl3·6H2O as the iron precursor. The resulting nitrogen-doped carbon nanosheets possess abundant defects (sp3-C/sp2-C = 0.66) and atomically dispersed iron species. The Fe/N–C catalyst exhibits outstanding catalytic activity for peroxydisulfate (PDS) activation, achieving over 98% phenol degradation within 30 minutes and a 60% total organic carbon (TOC) removal rate. Mechanistic studies, including radical quenching and electron paramagnetic resonance (EPR) experiments, reveal that both radical and non-radical pathways contribute to phenol degradation, with singlet oxygen (1O2) as the primary reactive oxygen species. Electrochemical analyses demonstrate that atomically dispersed Fe sites significantly enhance interfacial electron transfer. Post-reaction characterization indicates the consumption of pyrrolic-N, C=O, and carbon defects as active sites, while graphitic-N and Fe–N structures remain stable, confirming the catalyst's stability. This work provides an economical route to convert coal-tar pitch into high-performance catalytic materials for efficient water treatment, embodying the circular economy concept of waste-to-resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3945-8
Pillar[n]arenes, macrocyclic hosts with unique pillar-shaped architectures, exhibit dynamic planar chirality arising from restricted rotation of their hydroquinone units. This review summarizes recent advances in constructing chiral bis- and multi-macrocycles by fusing additional rings onto pillararene backbones. These systems serve as privileged platforms for chiral inversion molecular machines, particularly molecular universal joints (MUJs), and for integrating pillararenes with other macrocycles to create chiral platforms with circularly polarized luminescence (CPL). The design strategies, chiral inversion mechanisms, and attractive properties of these materials are discussed, highlighting their potential in chiral recognition, asymmetric catalysis, and chiral luminescent materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3784-9
Symmetry-breaking charge separation (SB-CS) is a fundamental process in natural photosynthesis and holds promise for organic semiconductor applications. However, the influence of SB-CS on excited-state chirality has remained unexplored. Here, we employ femtosecond time-resolved circularly polarized luminescence (TRCPL) and transient absorption (TA) spectroscopy to investigate the excited-state chirality dynamics of a chiral perylenediimide bichromophore (Cy-PDI 2). Our results reveal that the locally excited (LE) state decays to a symmetry-breaking charge-separated (SB-CS) state within 88 ps in tetrahydrofuran (THF), while this process is strongly quenched in toluene (TOL). Time-dependent emission dissymmetry factor g_lum(t) extracted from TRCPL kinetics demonstrates a one-order-of-magnitude enhancement of circularly polarized luminescence after SB-CS, directly reflecting the asymmetry of electron cloud distribution on an ultrafast timescale. This work provides the first direct observation of excited-state chirality evolution during SB-CS and proposes a mechanistic framework. Our findings offer deeper insight into the origin of excited-state chirality, which is crucial for understanding efficient energy transfer, enantiospecific recognition, and asymmetric catalysis in biological and chemical systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3833-1
Developing plasmonic nanomaterials with compositions beyond noble metals is crucial for expanding their applications. Transition metal nitrides, such as titanium nitride (TiN), exhibit excellent plasmonic optical properties and photothermal conversion efficiency, showing promise in catalysis, photothermal therapy, and seawater desalination. However, the structure-property relationship governing their plasmonic optical properties remains unclear. Here, we constructed Au@TiN core-shell nanostructures and systematically investigated the tunability of their geometry, composition, and optical properties. By varying the Au core size and TiN shell thickness, we achieved precise control over the localized surface plasmon resonance (LSPR) from visible to near-infrared wavelengths. Single-particle scattering spectroscopy revealed distinct plasmon hybridization modes, with experimental spectra matching theoretical simulations. The Au@TiN nanostructures exhibited enhanced photothermal conversion efficiency (η = 78.5%) under 808 nm laser irradiation, significantly outperforming pure TiN nanoparticles (η = 45.2%). This work demonstrates multi-factor control over plasmonic effects in TiN, providing insights for designing TiN-based plasmonic nanomaterials for catalysis and sensing.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509047
To reveal the dynamic characteristics of ecosystem carbon flux and its response to meteorological factors, this study employed the Biome-BGC model to simulate gross primary productivity (GPP) and net primary productivity (NPP) of vegetation in Beijing for historical (2001–2014) and future (2051–2070) periods under SSP126 and SSP585 scenarios, using multi-source data including regional meteorology, vegetation type, and soil texture. The Mann-Kendall (M-K) test and Empirical Orthogonal Function (EOF) analysis were applied to examine spatiotemporal patterns and carbon use efficiency (CUE). Results indicate that Biome-BGC accurately reproduces historical carbon flux characteristics. Temporally, annual mean GPP and NPP exhibited fluctuating upward trends, ranging from 584 to 777 g C m−2 a−1 and 238 to 388 g C m−2 a−1, respectively. Spatially, GPP and NPP displayed both same-phase and opposite-phase distribution patterns. Annual mean temperature was the dominant factor influencing GPP and NPP trends, followed by solar radiation and precipitation. Under future scenarios, both GPP and NPP are projected to increase, with SSP585 showing greater enhancement. By 2070, GPP is expected to rise by 171 and 376 g C m−2 a−1 under SSP126 and SSP585, respectively, while NPP increases by 71.8 and 137 g C m−2 a−1. The spatial distribution of GPP and NPP exhibits a 'low-center, high-periphery' pattern, with multi-year means of 969 and 425 g C m−2 a−1. Future CUE is approximately 0.45, indicating substantial carbon sequestration potential of Beijing's vegetation under climate change.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021602
Iron-based catalysts are widely used in water pollution treatment due to their high stability and redox capabilities. However, conventional single-component iron-based catalytic systems face challenges such as slow reaction kinetics and low efficiency in generating reactive oxygen species (ROS) during organic pollutant degradation. In this study, three electroactive bacteria (Bacillus megaterium, Lactococcus lactis, and Shewanella putrefaciens) were selected to interact with nano-Fe3O4 to construct bacterial/Fe3O4 hybrid materials, accelerating the degradation of gallic acid. The results showed that bacterial interaction with Fe3O4 facilitated rapid electron transfer, enhancing gallic acid degradation. The bacterial/Fe3O4 hybrid materials exhibited significantly higher gallic acid degradation rates compared to Fe3O4 alone. This improvement was mainly attributed to the ability of electroactive bacteria to promote the formation of oxygen vacancies (OVs) on the Fe3O4 surface, accelerating electron transfer and subsequently enhancing the generation of ROS, including hydroxyl radicals, superoxide radicals, and singlet oxygen. Correlation analysis demonstrated a significant positive relationship between OVs and ROS generation, with hydroxyl radicals showing the highest correlation with the gallic acid degradation rate constant (r = 0.98), indicating its dominant role in gallic acid degradation; the hydroxyl radicals quenching experiment also verified its dominant role. Additionally, due to the temperature sensitivity of bacteria, the degradation rate of gallic acid reached its peak in the temperature range of 30–40 °C. This study reveals the mechanism by which electroactive bacteria enhance the catalytic activity of Fe3O4, providing a new strategy for its application in advanced oxidation technology for water pollution treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022302
The escalating environmental contamination by mercury ions (Hg2+) poses severe risks to ecosystems and human health, necessitating the development of rapid, sensitive, and cost-effective detection methods. In this study, Fe1-xS@CNT composite nanozymes were synthesized via a straightforward solvothermal approach. The nanozymes exhibit uniform morphology, structural stability, and significant peroxidase (POD)-like activity. The incorporation of carbon nanotubes (CNT) facilitates electron transfer, enhancing the Fenton reaction between Fe2+/Fe3+ to generate abundant reactive oxygen species (ROS), primarily hydroxyl radicals (·OH) and superoxide anions (·O2−). The synergistic action of these ROS and photogenerated holes (h+) promotes the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) to a blue-colored product (oxTMB), establishing a colorimetric system of Fe1-xS@CNT + H2O2 + TMB. The specific binding of S2− on the nanozyme surface to Hg2+ inhibits POD activity, reducing the absorbance of the system. This principle was harnessed to develop a colorimetric method for Hg2+ quantification in environmental water samples. The method demonstrates a linear range of 0.1–500 μg·L−1 and a limit of detection (LOD) of 0.04 μg·L−1. Validation in real water samples (campus and tap water) showed recoveries between 94.4% and 111.1% with relative standard deviations (RSD) below 3.0%, comparable to atomic fluorescence spectrometry. The method offers advantages of simplicity, rapid analysis, and naked-eye visibility, providing a novel approach for on-site monitoring of heavy metal pollutants.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606010
Dissolved oxygen (DO) is a critical factor controlling endogenous phosphorus (P) migration in eutrophic waters. Existing oxygenation technologies suffer from high energy consumption and sediment disturbance, necessitating low-disturbance, pH-stable strategies that avoid additional nitrogen and P loads. This study evaluated an oxygen-loaded porous material (OLPM) for inhibiting sediment P release using laboratory microcosms with natural eutrophic water samples. DO microprofiles across the sediment-water interface (SWI) were measured with microelectrodes; diffusive gradients in thin films (DGT) resolved Fe, S, and P distributions; and sequential extraction quantified sediment P fractions. Results showed that OLPM coverage increased surface sediment DO concentration by 6.58-fold and DO penetration depth by 1.33-fold (16.8 mm). Overlying water total phosphorus (TP) decreased by 93.79%, and sediment interstitial phosphate (PO4-P) decreased by up to 45.75%. The SWI TP exchange flux reversed from +0.0068 mg/(m2·d) to -0.014 mg/(m2·d), shifting the system from a P source to a P sink. Sediment P fractionation revealed a 5.22% increase in stable Res-P and a 4.48% decrease in labile NaHCO3-P. Mechanistically, OLPM enhanced iron oxidation (Fe2+ reduced by 59.62%) and suppressed sulfate reduction (S2- homogenized at low levels), promoting P immobilization via Fe-S coupling. The material effectively inhibits endogenous P release through interfacial DO regulation without altering pH, offering a promising approach for eutrophication management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606009
The escalating volume of municipal solid waste in China necessitates effective disposal strategies. Industrial kiln co-processing offers a promising route, but high-temperature decomposition of chlorinated components releases HCl and Cl2, causing severe equipment corrosion and operational issues. This study investigates the high-temperature dechlorination performance of fly ash and red mud, two abundant industrial solid wastes, as potential dechlorination agents. Using a high-temperature tube furnace system, dechlorination efficiencies were evaluated across 600–900 °C. At 700 °C, fly ash achieved a peak dechlorination efficiency of 93.33%, while red mud reached 88.61%. However, efficiencies declined with further temperature increase, dropping to 65.6% and 58.27% at 900 °C for fly ash and red mud, respectively. To enhance performance at higher temperatures, fly ash was modified via alkali (NaOH) treatment. The modification increased surface roughness and porosity, disrupted Si-O-Si and Si-O-Al networks, and exposed active sites. Consequently, the alkali-modified fly ash exhibited a peak dechlorination efficiency of 94.98% at 800 °C, a 23.08% improvement over unmodified fly ash (71.9%). These findings demonstrate the technical feasibility of utilizing solid wastes as dechlorination agents, offering a dual benefit of waste valorization and cost-effective high-temperature gas purification. The study provides a foundation for scaling up this approach in industrial kiln applications, contributing to sustainable waste management and reduced environmental impact.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511087
Identifying the sources and driving factors of heavy metals (HMs) in paddy soils around mining areas is crucial for safeguarding regional agricultural production and food security. This study focused on paddy soils near a mining area in southern Jiangxi Province, integrating Spearman correlation analysis, positive matrix factorization (PMF), and extreme gradient boosting (XGBoost) coupled with SHapley Additive exPlanations (SHAP) to quantitatively apportion potential ecological risks, pollution sources, and driving factors. Results showed that mean concentrations of Pb, Ni, and Cu exceeded the soil background values of Jiangxi Province, except for Cr. The mean comprehensive potential ecological risk index (RI) was 17.4, with 25.7% of sampling sites exhibiting moderate risk, and Ni being the primary ecological risk factor. Source apportionment identified three main sources: natural background (51.1%), industrial and mining activities (26.6%), and a mixed source of agricultural activities and traffic emissions (22.3%). Spatial variation of Cr, Cu, and Ni was predominantly governed by soil physicochemical properties (Fe and P contents), whereas Pb distribution was significantly influenced by industrial and mining activities. The combination of PMF and XGBoost-SHAP effectively delineated sources and driving factors, providing a scientific basis for targeted soil management and pollution control in mining-affected agricultural regions.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511002
To treat large-air-volume, low-concentration volatile organic compounds (VOCs) containing tetrachloroethylene (PCE) generated from rubber-metal bonding, this study systematically investigated the adsorption-desorption behavior and interaction mechanisms of PCE, toluene, and methyl isobutyl ketone (MIBK) on granular activated carbon (GAC). Static adsorption experiments showed that PCE adsorption capacity reached 556.6 mg·g−1, while dynamic multi-component adsorption capacity was 179.6 mg·g−1. Kinetic analysis indicated that PCE adsorption was controlled by both intraparticle diffusion and external surface adsorption, whereas toluene and MIBK were primarily intraparticle diffusion-limited. During high-temperature nitrogen desorption, PCE underwent dechlorination, hydrogenation, and recombination, producing trichloroethylene, 1,2-dichloroethane, 1,2-dichloropropane, and HCl, with HCl accounting for 3.61% of the chlorine molar content in adsorbed PCE. After four adsorption-desorption cycles, the iodine value of GAC dropped below the industry standard of 600 mg·g−1; however, water washing and alkali immersion extended the cycle life to 8 and 9 cycles, respectively. The HCl generation pattern in co-adsorption systems was consistent with single-PCE systems. A regeneration process combining alkali immersion and water washing was proposed and integrated into an engineering strategy. Compared to conventional activated carbon adsorption coupled with RTO incineration, the proposed classification strategy reduced annual costs by 49.5×10⁴ CNY. This work provides a cost-effective and safe solution for Cl-VOCs treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040705
Chromium is a common environmental metal pollutant. Shewanella oneidensis MR-1 can generate extracellular electrons, facilitating the reduction of Cr(VI) to Cr(III), thereby mitigating its toxicity. Both biochar and electroactive dissolved organic matter (e-DOM) regulate extracellular electron transfer during Cr(VI) bioreduction. In practice, surface DOM on biochar can detach and enter the environment, while the biochar matrix (BCM) remains the predominant form and coexists with e-DOM. However, the combined effects of BCM and e-DOM on microbial Cr(VI) removal are unclear. This study investigated the individual and combined impacts of biochar matrix and AQDS (a model e-DOM) on Cr(VI) reduction by S. oneidensis MR-1. Results showed that biochar matrix or AQDS alone promoted Cr(VI) removal, primarily by accelerating electron transfer during the fast reduction phase. However, when both were added, an antagonistic effect was observed, attributed to increased repulsive forces between the biochar matrix-AQDS complex and the bacterial cells, which inhibited electron transfer to Cr(VI). This research elucidates the electrochemical interactions between biochar matrix and e-DOM, providing a theoretical basis for biochar applications in environmental remediation and risk assessment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607004
Pelletizing technology is widely applied in biomass and coal fuel processing, offering advantages in transport, storage, and energy density. Coal gasification fine slag (CGFS), a carbon-rich coal-based solid waste, holds potential as a fuel. This study prepared centimeter-scale composite pellets by blending CGFS with various biomass types under 6 MPa at room temperature for 2 minutes. Combustion and emission characteristics were investigated using a self-developed flat-flame macro-thermogravimetric reactor simulating high heating rate conditions. Results showed that biomass type significantly influenced combustion due to chemical composition differences. Introducing biomass altered fuel particle composition, enhancing combustion rates of single-component fuels by 3–5 times during volatile combustion. Co-combustion reduced NOx and CO emissions by over 50% compared to pure CGFS. Higher biomass ratios accelerated volatile release and shortened burnout time but increased NO emissions due to higher volatile nitrogen content. Conversely, CO emissions decreased due to improved char combustion conditions. These findings provide critical experimental support for optimizing clean and efficient solid fuel production from CGFS and biomass.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3966-0
The development of low platinum-loading catalysts for the economically viable hydrogen evolution reaction (HER) remains challenging. Herein, a precursor dilution strategy is used to fabricate Pt nanoclusters anchored on Ni-embedded porous carbon microspheres. The approach begins with the facile synthesis of Zn/Ni-based coordination polymers (Ni-BTC-Zn) due to the isomorphic substitution of Zn2+ and Ni2+. During pyrolysis, the evaporation of zinc species results in a highly porous carbon structure with well-dispersed nickel nanoparticles. Subsequent solvothermal treatment allows for the uniform deposition of Pt nanoclusters to form the final bimetallic PtNi catalysts (PtNi-BTC-C). Among them, the optimized PtNi-BTC-C10 exhibits exceptional alkaline HER performance, requiring an overpotential of only 41 mV to achieve 10 mA cm−2 and a low Tafel slope of 31.1 mV dec−1. It also demonstrates outstanding durability with a current retention of 90.7% after 70 h, far exceeding Pt/C. Extensive characterization confirms that moderate Zn dilution optimally modulates the Ni particle size and dispersion, leading to maximized active sites and enhanced charge transfer. Combined with DFT calculations, the Pt-Ni-cluster model for PtNi-BTC-C10 possesses an optimized electronic structure with a shifted d-band center, which facilitates water dissociation and optimizes H* desorption with the most favorable energetics (0.262 eV). This work provides a fundamental understanding of precursor dilution engineering and offers a versatile pathway for designing advanced noble-metal-based bimetallic electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3892-2
Single-atom co-catalysts on semiconductor substrates offer a cost-efficient route to enhance photocatalytic performance with minimal precious metal loading. However, precise tuning of local coordination environments and construction of efficient single-atom co-catalysts remain challenging for overall water splitting. Here, we employ an icing-assisted photochemical reduction strategy to anchor atomically dispersed Pt species as hydrogen evolution co-catalysts on Al3+-doped SrTiO3 (Pt SA-STO). The optimized Pt SA-STO exhibits remarkable activity, with hydrogen and oxygen evolution rates of 13.62 and 6.71 mmol h−1 g−1, respectively, and a turnover frequency (TOF) of 2114.5 h−1. We pioneer the use of nuclear magnetic resonance (NMR) spectroscopy to quantitatively track the temporal evolution of Pt4+ to Pt2+ under continuous irradiation during the icing-assisted photoreduction. Advanced characterizations and theoretical calculations confirm that single-atom Pt co-catalysts facilitate directional transfer and extraction of photogenerated charge carriers, effectively suppressing surface recombination. This work provides insights into designing novel single-atom co-catalysts by deepening understanding of electronic configurations and active sites in photocatalytic overall water splitting.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608009
To investigate the flow and heat transfer characteristics of natural draft direct air-cooling towers (NDC) for large coal-fired power generating units, a three-dimensional CFD numerical model covering major plant buildings, air-cooled radiators, and ambient wind fields was established based on the NDC systems of a 2×660 MW unit of a power plant. The influences of meteorological factors, including ambient wind speed, ambient temperature, and ambient wind direction, as well as regulation measures such as rolling shutters, louvers, and bypass windows on the heat dissipation performance of NDC towers were systematically analyzed. The results demonstrate that ambient wind speed acts as the dominant factor governing the performance of the NDC system. As wind speed rose, the uneven distribution of air intake volume and heat dissipation among each cooling delta increased remarkably, which elevated the unit back pressure, and the upstream tower suffered more severe impacts than the downstream one. Ambient temperature exerted a slight effect on circumferential flow distribution, yet substantially changed the overall back pressure of the system. In terms of regulation strategies, closing rolling shutters in the windward zone and reducing the opening of partial louvers can improve air flow redistribution to a certain extent, but will reduce the total air flow rate and total heat dissipation of the entire tower. By contrast, bottom bypass windows can effectively optimize the air intake on the leeward side and boost heat dissipation under high-wind operating conditions, whereas top bypass windows deliver only limited improvement effects. This research can provide fundamental data and technical references for the optimal design, operational regulation, and energy-saving retrofitting of large NDC units.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022402
Graphene oxide–silver nanoparticle (GO-AgNPs) nanocomposites synergistically combine the high specific surface area and biocompatibility of graphene oxide with the potent antibacterial and optical properties of silver nanoparticles. This review systematically examines current synthetic strategies—physical, chemical, and biological—and their influence on nanocomposite morphology, loading efficiency, and stability. The biomedical applications of GO-AgNPs are critically analyzed, focusing on antimicrobial activity, anticancer therapy, drug delivery, and biosensing. Mechanistic insights reveal that antimicrobial action involves membrane disruption, oxidative stress, and damage to biomolecules, while anticancer effects are mediated through reactive oxygen species (ROS) generation. The review also addresses challenges such as AgNP aggregation and stability, which are mitigated by GO support. Future directions emphasize the development of multifunctional nanomedicine platforms, with a need for standardized toxicity assessments and scalable synthesis. This comprehensive overview aims to guide further research and clinical translation of GO-AgNPs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4060-5
Organic solar cells (OSCs) offer unique advantages for wearable electronics due to their light weight and mechanical flexibility. However, achieving both high optoelectronic performance and mechanical robustness in organic semiconductors remains challenging, compromising the efficiency and durability of stretchable OSCs. Here, we report a cross-linked conjugated polyelectrolyte (CPE)-polyoxometalate (POM) anode interlayer (AIL), PTN-POM, constructed via strong electrostatic interactions between ammonium groups and POM. The PTN-POM film exhibits an electrical conductivity of 3.30×10−3 S/m and high stretchability, significantly outperforming the classic PEDOT:PSS AIL in mechanical strength. Binary OSCs modified with PTN-POM achieve a power conversion efficiency (PCE) of 19.59%, the highest reported for OSCs using a cross-linked AIL. Notably, PTN-POM enables fabrication of water-proof OSCs that show no performance degradation after underwater storage for 42 days. Furthermore, stretchable OSCs incorporating PTN-POM demonstrate enhanced mechanical robustness, retaining 81% of initial PCE under a large tensile strain of 50%. This work significantly enhances the photovoltaic, waterproof, and mechanical properties of OSCs, advancing their potential for wearable photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4030-y
In the era of artificial intelligence, efficient perception and processing of massive visual information demand advanced machine vision systems. Inspired by human visual adaptation, various optoelectronic devices have been developed, yet most rely on external gate voltages or complex circuits for dynamic sensitivity modulation. This work demonstrates an all-optically controlled biomimetic sensor based on a one-dimensional ZnO/MAPbBr3 heterojunction, achieving both positive and negative photoconductivity effects. By modulating oxygen vacancy states with ultraviolet light, the competition between intrinsic photoconduction and trap-mediated carrier capture is regulated, enabling dynamic control of visible-light photoresponse within a single device. This tunable behavior mimics scotopic adaptation (photopigment regeneration under weak illumination), photopic adaptation (photopigment bleaching in bright environments), and eyelid-like self-protection against intense light. The device operates without external gate bias or cascaded circuits, offering a promising strategy for next-generation intelligent biomimetic sensors in machine vision.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4033-1
Photodetectors are critical components in modern optoelectronic systems, underpinning applications in optical communication, low-altitude economy, environmental monitoring, and national defense. Layered two-dimensional (2D) materials such as MoS2, WS2, black phosphorus (BP), and ReS2 have attracted extensive attention due to their remarkable electronic and optical properties, including facile mechanical exfoliation and tunable characteristics via thickness engineering. The absence of dangling bonds enables the construction of van der Waals (vdW) heterostructures free from lattice-matching constraints, promoting efficient charge transport, enhanced light absorption, and suppressed dark current. Among layered materials, semimetals such as graphene, PdTe2, MoTe2, and TaIrTe4 exhibit narrow or zero bandgaps, enabling ultrabroadband spectral responses from ultraviolet (UV) to terahertz (THz). ZrTe3, a layered gapless semimetal, demonstrates pronounced carrier transport features, including robust excitons and ultrafast carrier relaxation times, making it an ideal candidate for photodetection. However, pure ZrTe3-based photodetectors suffer from substantial dark current due to the absence of an energy bandgap, degrading signal-to-noise ratio and specific detectivity (D*). This work reports a high-performance broadband photodetector based on a ZrTe3/CuInP2Se6 heterostructure. By exploiting an asymmetric contact configuration that introduces a Schottky barrier, the device effectively suppresses dark current while enhancing photoresponse. The photodetector exhibits broad spectral sensitivity from UV to near-infrared (355–1177 nm), microsecond-level response speed, and high responsivity and specific detectivity. Beyond conventional photodetection, an optoelectronic information encryption-decryption application is demonstrated, where modulated light and bias voltage serve as dual input channels to encode and decode ASCII signals. This study resolves the challenge of high dark current in semimetal-based photodetectors and introduces a multifunctional platform for secure optoelectronic communication, highlighting the potential of ZrTe3 for next-generation photonic and quantum information technologies.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60692-5
Long persistent luminescence materials (LPLMs) have demonstrated significant potential in photo- and electro-catalysis due to their unique capability of storing and controllably releasing photogenerated charge carriers. These materials offer innovative solutions for environmental remediation and sustainable energy technologies. This review systematically summarizes recent advances in the application of LPLs in photo- and electro-catalysis, outlining their developmental history and underlying mechanisms. Emphasis is placed on their applications in organic pollutant degradation, photocatalytic hydrogen evolution, and photovoltaic cells. Furthermore, design strategies and research frameworks for LPLs are discussed. The current limitations and challenges in this field are examined, and future research directions are proposed to facilitate the transition of LPLMs from fundamental research to practical applications in energy and the environment. Key materials such as SrAl2O4:Eu2+,Dy3+ exhibit afterglow lasting up to 30 hours, enabling round-the-clock catalytic activity. Composite systems like g-C3N4@Au@SrAl2O4:Eu2+,Dy3+ and Cu|CuO/SrAl2O4:Eu2+,Dy3+ have achieved efficient degradation and simultaneous hydrogen evolution. Z-scheme heterojunctions, e.g., Sr2MgSi2O7:Eu2+,Dy3+/Ag3PO4, demonstrate enhanced performance. The review highlights the potential of LPLMs to overcome the limitation of intermittent light sources, providing a pathway for continuous catalytic processes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4126-0
Flexible X-ray detectors are constrained by the difficulty of producing semiconductor films that simultaneously exhibit uniform morphology, high crystallinity, and mechanical robustness. Here, we introduce a hydrogen-bond engineered supramolecular (HBES) strategy to overcome these limitations in supramolecular bismuth halide clusters (PDBiI5). By incorporating polyacrylic acid (PAA), a dynamic supramolecular network is formed that suppresses the coffee-ring effect during ultrasonic spray-coating via increased solution viscosity and controlled kinetic balance between solvent evaporation and solute diffusion. The HBES approach also modulates crystallization kinetics, extending crystal growth time from 23 to 41 s, yielding densely packed films with enhanced crystallinity and reduced defect states. These improvements lead to superior charge transport: a hole mobility of 2.16 cm2 V−1 s−1 and a mobility-lifetime product of 9.1 × 10−4 cm2 V−1. The resulting X-ray detectors achieve a record sensitivity of 19,009 μC Gyair−1 cm−2 and an ultralow detection limit of 3.35 nGyair s−1, with excellent operational and environmental stability. Leveraging the mechanical robustness from the supramolecular network, we demonstrate the first direct-type flexible X-ray imager, retaining 85% performance after 1000 bending cycles. This imager overcomes geometric distortion and vignetting, maintaining 85% edge photocurrent versus 58% for rigid detectors, enabling clear imaging of curved objects. This work establishes a versatile supramolecular engineering paradigm for high-performance flexible X-ray detection and imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4173-x
Ferroelectric memory, with its promise of low power consumption, high writing speed and exceptional endurance, requires the scaling of ferroelectric films to ultrathin dimensions—often just a few atomic layers thick. However, such extreme thinning risks destabilizing or even erasing electric polarization, mainly due to the detrimental depolarization field. Remarkably, certain ferroelectrics exhibit an intrinsic immunity to this effect, as predicted theoretically and confirmed experimentally. Examples include improper ferroelectrics, hyper ferroelectrics, engineered heterostructures, and low-dimensional van der Waals ferroelectrics. This review systematically examines these unique materials, unravelling the fundamental physics behind their polarization robustness and the mechanisms enabling them to resist the depolarization field. By bridging theory with experimental advances, we aim to inspire the design of next-generation ferroelectrics capable of overcoming critical challenges encountered in practical ferroelectric memory devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4132-y
Manganese-iron-based mixed polyanionic cathodes are promising for sodium-ion batteries (SIBs) due to high energy density and operating voltage, but suffer from Jahn-Teller distortion of Mn3+ that degrades cycling stability. Here, a structural modulation strategy via Mg2+ doping is reported. Electrochemically inert Mg2+ forms stronger chemical bonds, adjusts lattice parameters, and suppresses Jahn-Teller distortion, enhancing structural stability. Mg2+ also widens sodium-ion diffusion channels, improving diffusion kinetics. Additionally, an in-situ three-dimensional carbon nanotube (CNT) conductive network boosts electronic conductivity. The resulting NFMPP-Mg@CNTs cathode delivers a discharge capacity of 126 mAh g−1 at 0.1 C (near theoretical 129 mAh g−1), retains 80% capacity after 3000 cycles at 0.5 C, and achieves an energy density of 401 Wh kg−1, among the highest reported for mixed phosphate systems. Ex-situ XPS and first-principles calculations confirm that Mg2+ resists geometric distortion by enhancing lattice stability and widening Na+ diffusion pathways (migration barrier reduced from 0.566 to 0.398 eV). This work provides a viable route for high-energy, long-life SIB cathodes suitable for large-scale energy storage.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3551-5
Flexible photonic crystal (PC) materials exhibit exceptional optical properties but suffer structural degradation under repeated mechanical stress, leading to photonic band gap impairment and limited sustainability. This study introduces a self-healing thermoplastic polyurethane (STPU) with an inverse-opal PC structure, inspired by natural structural coloration and self-healing mechanisms. Synergistic dynamic covalent disulfide bonds and hydrogen bonds enable reversible mechanical adjustment, yielding a tensile strength of 26.76 MPa and elongation at break of 2000%. The inverse opal structure facilitates reversible color transitions in response to solvents (water, ethanol) and mechanical strain (0–70%) via lattice spacing modulation. Incorporating an interpenetrating network of polyacrylamide hydrogel and carbon nanotubes enhances strain sensitivity and structural color stability. The material demonstrates broad potential in flexible sensors, adaptive optical devices, bioinspired robotic skins, and dynamic anti-counterfeiting encryption, overcoming traditional PC limitations such as high fragility and single functionality. This strategy advances durable intelligent sensing materials with enhanced environmental adaptability and multifunctional integration.