SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4244-0
Near-infrared perovskite light-emitting diodes (NIR-PeLEDs) suffer from poor operational stability, largely due to interfacial reactions at the electron-transport layer (ETL)/perovskite interface. Here, we introduce a zinc ion (Zn2+)-chelated hybrid ETL derived from a Zn2+-chelated polyethylenimine ethoxylated (PEIE) complex, which partially retains the surface properties of ZnO but exhibits significantly reduced oxygen defects and surface-adsorbed hydroxyl groups. This well-modulated surface promotes perovskite crystallization and mitigates interface-induced deprotonation of organic cations during device operation. Consequently, NIR-PeLEDs employing this hybrid ETL achieve a peak external quantum efficiency (EQE) of 20.1%, a high radiance of 652 W sr-1 m-2, and an exceptional T50 lifetime of 270.7 hours at a high current density of 100 mA cm-2, which is over five times that of devices based on conventional ZnO nanocrystal (NC) ETLs. Our results present an effective ETL strategy for operationally stable NIR-PeLEDs and thoroughly reveal the critical role of regulating interfacial reactions in stabilizing buried interfacial contacts. These findings provide valuable insights for advancing perovskite optoelectronic devices that suffer from interface-induced performance degradation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3607-9
Enhancing light olefin selectivity and extending catalytic durability remain critical challenges for ZSM-5 zeolites in methanol-to-olefins (MTO) conversion, primarily due to inherent diffusion restrictions along the MFI b-axis and poor coke accommodation. Here, we report a hierarchically single-crystalline ZSM-5 sheet architecture featuring interconnected multiscale porosity and a remarkably reduced b-axis thickness (<50 nm), quantitatively verified by three-dimensional electron tomography. Real-time confocal laser scanning microscopy tracking demonstrated significantly enhanced molecular diffusivity compared to conventional micron-sized ZSM-5 (Micro-ZSM-5). This engineered structure distributes abundant aluminum sites on highly accessible diffusion pathways, achieving an enlarged coke accommodation of 16.31 wt% with a coke deposition rate of 0.59 mg g−1 h−1, only one third of that in Micro-ZSM-5. In continuous MTO operation, the hierarchical ZSM-5 sheet (Hier-ZSM-5-S) maintained an average ethylene and propene selectivity of 63.5% for 22.2 hours (WHSV = 3.6 h−1, T = 480°C), which was 19% higher and 6.5 times longer than Micro-ZSM-5, respectively. This hierarchically shortened b-axis structure establishes a generalizable paradigm for enhanced diffusion and coke accommodation in precisely designed pore systems, applicable to various reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3777-0
Optically clear adhesives (OCAs) are critical for next-generation optoelectronic systems, yet their end-of-life management remains a sustainability challenge. Here, we report a debondable and robust polyurethane (PU)-based OCA that integrates both mechanical and chemical recyclability. The PU-based OCA exhibits high optical transparency (>90% transmittance from visible to near-infrared), strong adhesion to glass and polymeric substrates (bonding strength up to 5.0 MPa), and thermally sensitive H-bonding interactions that enable on-demand deadhesion at elevated temperatures. This capability facilitates non-destructive detachment of functional assemblies, promoting component reuse and material recycling. The adhesive demonstrates excellent mechanical properties, including ductility and strength, and outperforms several commercial optical adhesives in key performance metrics. Its straightforward synthesis and industrial scalability make it a promising solution for advancing circular economy principles in optoelectronic device manufacturing. The work addresses critical bottlenecks in balancing mechanical performance, adhesion/detachment, and recyclability, offering a transformative approach to sustainable advanced manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3716-x
Flexible pressure sensors (FPSs) are pivotal for fall detection and rehabilitation training, yet conventional synthetic-based sensors suffer from resource-intensive manufacturing, high costs, and environmental pollution. This study introduces a sustainable fabrication strategy for FPSs using natural materials. Electrodes were fabricated by treating natural wood strips with a flame retardant, converting them into high-quality graphene via cost-effective infrared laser processing, and transferring onto starch-based substrates. The dielectric layer comprised an electrospun composite nanofiber membrane of cyclodextrin and carbon nanotubes. The resultant capacitive FPS exhibited high sensitivity (2.15 kPa⁻¹ within 0–10 kPa), a low detection limit (~6.5 Pa), rapid response and recovery times (29 ms and 39 ms), and excellent long-term stability exceeding 5000 cycles. Biocompatibility was outstanding (cell viability >98%), and the sensor fully degraded within 6 hours. Integrated with wireless technology, the sensor enabled a fall detection and rehabilitation monitoring system. Data processing utilized a Tiny Machine Learning module on a mobile platform, transmitting data to a cloud-based system. The system accurately identified five common fall postures and assisted clinicians in guiding rehabilitation exercises, achieving recognition accuracies of 99% and 100%, respectively. This work offers a sustainable healthcare solution for elderly care, addressing environmental and economic limitations of existing FPS technologies.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604015
Shale gas extraction generates hazardous oily sludge, necessitating effective in-situ treatment. Microemulsion technology offers low energy consumption, cost efficiency, and high oil removal without heating. This study investigates single-surfactant microemulsions using sodium dodecyl sulfate (SDS) and alpha-olefin sulfonate (AOS), and composite microemulsions with sodium silicate (Na2SiO3). Phase behavior and effects of surfactant, alcohol, and salt concentrations on oil removal were examined. Optimal single formulations achieved removal rates of 86.33% for SDS (SDS:alcohol:NaCl = 2.72%:13.21%:2.17% mass ratio) and 87.45% for AOS (SDS:alcohol:NaCl = 2.72%:15.41%:2.17%). SDS microemulsions showed superior phase stability despite slightly lower removal efficiency. Composite SDS-Na2SiO3 microemulsion achieved 92.47% oil removal, outperforming single systems, and could be recycled five times while meeting national secondary reuse standards. AOS-Na2SiO3 exhibited better salt resistance, whereas SDS-Na2SiO3 showed better alcohol resistance. This work provides a novel approach for in-situ oily sludge treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507094
To address land waste and poor bearing capacity from sludge landfill, this study developed a composite solidifying agent using loess, fly ash, desulfurized gypsum, and cement. Orthogonal experiments combined strength testing, SEM/XRD microanalysis, permeability and heavy metal leaching tests, and cost accounting. Results show that cement significantly enhances early and mid-term strength, while loess dominates later strength development. Optimal fly ash and desulfurized gypsum content is 12% each. The optimal mix ratio (loess:fly ash:desulfurized gypsum:cement:sludge) is 0.1:0.12:0.12:0.08:1. The solidified matrix forms dense structures via C-S-H gel and ettringite (Aft), effectively controlling heavy metal leaching at low cost. This work enables solid waste resource utilization and provides robust support for sludge solidification engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3814-2
Micro-structured surfaces have attracted increasing attention due to their great potential applications. However, it is still a challenge to continuously fabricate micro-structured surfaces based on thermoplastics by a facile, low-cost, and environmentally-friendly method. Herein, with the help of the extrusion molding method and an elaborately designed mold, micro-grooved fiber (MGF) based on high-density polyethylene (HDPE) is continuously prepared. Theoretically, infinitely long MGFs with feature sizes down to a few microns can be efficiently fabricated because of the continuous fabrication characteristic of the melt extrusion method. Interestingly, left- and right-handed micro-grooves with different helix angles can be produced by applying twisting at the die exit, and the macroscopically MGF springs can be further fabricated via a self-designed three-dimensional helical enwind device. By regulating wettability, MGF can achieve liquid self-transport on predefined paths. In addition, MGF fabric exhibits rapid evaporation behavior, whose evaporation rate is about 4 times higher than that of the Smooth fiber (SMF) fabric and 2 times higher than that of the most popular commercial quick-drying fabric (i.e., Cool-max fabric). This work proposes a facile and environmentally-friendly method for continuously preparing low-cost and flexible MGF, opening a new pathway to develop fiber-based microfluidic systems following the concept of "functionalized processing for thermoplastics".
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021805
This study analyzed 75 precipitation samples collected from August 2017 to August 2018 in the Meili Snow Mountain region of the Hengduan Mountains. The chemical characteristics of inorganic ions and their seasonal variations between monsoon and non-monsoon periods were examined. The volume-weighted mean total ion concentration was 246.2 μeq·L–1, with higher concentrations in the non-monsoon season and lower in the monsoon season. The dominant water chemistry type was HCO3–-Ca2+. Principal component and partial correlation analyses indicated that Ca2+, Mg2+, HCO3–, and SO42– mainly originated from local sedimentary rock dust, while Na+ and Cl– were primarily marine during the monsoon, with reduced marine influence in the non-monsoon period. NO3– was largely attributed to South Asian pollution emissions, with significant contributions from biomass burning to K+, Na+, and Cl– in the pre-monsoon phase. PMF source apportionment confirmed that during the monsoon, approximately 70% of Cl– and Na+ were from sea salt, whereas in the non-monsoon, over half came from biomass burning. NO3– was almost entirely from fossil fuel combustion during the monsoon (96%), decreasing to 72% in the non-monsoon. Ca2+ and Mg2+ were mainly from carbonate dust in the monsoon and weathered dust in the non-monsoon. Backward trajectory analysis showed that the non-monsoon period was dominated by westerly transport (60%), while the monsoon was dominated by southwest monsoon transport (81%). These findings provide scientific basis for understanding atmospheric pollution and background values in the region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3863-x
Lead-free double perovskites are promising for optoelectronic applications due to their tunable optical properties, stability, and non-toxicity. However, achieving efficient ultrabroadband near-infrared (NIR) emission and X-ray radioluminescence (RL) simultaneously remains challenging. Here, we report a Mo4+-doped Cs2(Na0.4Ag0.6)InCl6 double perovskite that exhibits efficient blue-light-excitable NIR emission with a near-unity photoluminescence quantum yield. The emitter demonstrates robust thermal stability, retaining 84% of its initial emission intensity at 420 K relative to 300 K. Under X-ray irradiation, the material shows bright NIR RL with a high light yield of 39,400 ± 1100 photons/MeV. A flexible film of Mo4+-doped Cs2(Na0.4Ag0.6)InCl6/polydimethylsiloxane (PDMS) was fabricated and applied as an NIR light source and X-ray scintillator. A dual-functional platform for cooperative NIR and X-ray imaging was established using a bullfrog palm as the target, achieving pixel-level fusion of NIR and X-ray images without spatial mismatch or complex image processing. The fused image simultaneously visualizes blood vessels and skeleton textures under the skin tissue. This work provides a viable strategy for lead-free double perovskites in advanced optoelectronic devices, particularly for multispectral imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3869-7
Iontronic capacitive pressure sensors (ICPSs) are pivotal for wearable technology, yet their performance is constrained by an inherent trade-off between sensitivity and detection range. Here, we introduce a micro-electric double layer (micro-EDL) engineering strategy to overcome this limitation. This is realized through a nanocomposite dielectric where multi-walled carbon nanotubes (MWCNTs) form a percolated network, generating a dense array of pressure-responsive nano-capacitors. Synergistically integrating a hierarchical MoS2/NiCo-LDH electrode provides abundant pseudocapacitive interfaces. The resulting sensor exhibits an ultrahigh sensitivity of 67,095 kPa−1 at 1 kHz, a broad detection range up to 1.3 MPa, rapid response and recovery times of 4 ms and 5 ms, respectively, and outstanding durability exceeding 18,000 cycles. Practical validation demonstrates 100% classification accuracy in recognizing complex gestures and gait patterns, underscoring its real-world applicability. These findings establish micro-EDL engineering as a promising route for advancing next-generation iontronic devices, offering insights into their electrochemical mechanisms.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608026
Biochar and microbial inoculants are widely used for agricultural soil amendment. To investigate the effects of different straw biochars and Bacillus subtilis inoculant, applied individually or combined, on nitrogen transformation in dryland soil, a 60-day laboratory incubation experiment was conducted with six treatments: control (CK), 4% rice straw biochar (S), 4% rapeseed straw biochar (Y), 4% rice straw biochar plus 5 mg/kg inoculant (SJ), 4% rapeseed straw biochar plus 5 mg/kg inoculant (YJ), and inoculant alone (J). Results showed that rice straw biochar significantly increased soil nitrate nitrogen content by 148.74%–152.68% compared to CK, enhancing nitrification. Combined application with inoculant further increased average net nitrogen mineralization rate by 77.28%–99.38%. Conversely, rapeseed straw biochar decreased nitrate nitrogen by 51.66%–57.61%, and combined application reduced net nitrogen mineralization rate by 82.07%–84.73%. Treatments S, Y, SJ, and YJ promoted microbial biomass nitrogen (MBN) synthesis, with S and Y increasing MBN by 2.02- and 2.20-fold over CK, respectively. Combined treatments further increased MBN by 103.26%–149.44% relative to single biochar treatments. These findings indicate that biochar type governs nitrification and net nitrogen mineralization, while combined application exerts synergistic effects on MBN. For comprehensive dryland soil improvement, YJ treatment is optimal, reducing inorganic nitrogen loss risk and enhancing microbial nitrogen activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4124-x
Aerogel fibers, featuring distinct porous architecture and fiber flexibility, have emerged as leading materials for personal thermal protection; however, complex drying processes and singular thermal insulation mechanisms limit their use in complex environments. Here, aramid nanofiber/carbon nanotube (ANF/CNT) aerogel fibers integrating passive thermal insulation and active solar heating were fabricated via wet-spinning and ambient-pressure drying (APD). The incorporation of CNT and Ca2+ generates abundant physical and chemical crosslinking points, strengthening the nanofiber network skeleton and reducing structural collapse during APD to only 8.9% shrinkage. The resulting ANF/CNT aerogel textiles exhibit low thermal conductivity of 33.8–40.4 mW/(m K) and thermal insulation capability from −196 to 400 °C. The photothermal effect of CNT enables active solar heating, effectively supplementing passive insulation and allowing survival in extremely cold environments. In real tests, the synergistic effect improved skin temperature by up to 5.9 °C, significantly higher than 1.6 °C from passive insulation alone. These ANF/CNT aerogel fibers combine flexibility, mechanical strength, and flame retardancy, demonstrating promising potential for smart, controllable personal thermal management applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4085-9
Bone defects remain a prevalent clinical challenge, and regenerative medicine based on bone tissue engineering offers promising solutions. Traditional osteogenic materials rely on bioactive macromolecules like growth factors, which suffer from poor stability and stringent storage requirements. From a structural perspective, bone tissue resides in a phosphorylated microenvironment, with 65–70% of inorganic components composed of hydroxyapatite. Inorganic phosphorylated materials induce osteogenic differentiation but exhibit high stiffness, brittleness, slow degradation, and limited mechanical tunability. Synthetic phosphorylated polymers with excellent mechanical properties and biocompatibility have been developed to address these issues. In this work, we developed a series of phosphorylated polymers derived from poly(glycerol sebacate) (PGS), a biocompatible and biodegradable material. Leveraging the hydroxyl-rich backbone of PGS, we demonstrated an efficient method for controllable phosphorylation of PGS side chains, enabling synthesis of PGS-based phosphorylated (PGS-P) polymers with tunable phosphorus contents. The optimized phosphorylated polyester, PGS-P4, exhibited strong ability to promote osteogenic differentiation of rat BMSCs, and its porous three-dimensional scaffolds showed favorable properties for bone regeneration. BMSCs cultured for one week and observed by fluorescence microscopy showed enhanced BSP protein expression on PGS-P2, PGS-P4, and PGS-P6 groups compared with PLGA and PGS, with PGS-P4 displaying the most intense signal. In summary, we present a simple and controllable method for preparation of functionalized polyesters and their porous scaffolds with tunable phosphorus content, validating its effectiveness in promoting osteogenic differentiation of rat BMSCs. All phosphorylated polyesters exhibit enhanced differentiation-promoting effects compared to non-phosphorylated PGS; however, the degree of enhancement does not increase monotonically with phosphorus content. PGS-P4, containing an optimal phosphorus level, shows the most pronounced biological functions.