SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4236-8
Electrochemical nitrate reduction (NO3RR) to ammonia offers a sustainable route for nitrogen recovery from wastewater, yet its efficiency is constrained by complex multi-step proton-electron transfers and competitive hydrogen evolution. Here, we report a series of binary cobalt-copper phosphates with precisely tuned Co/Cu ratios, revealing a volcano-type relationship between composition and catalytic activity. The optimized Co0.5Cu1.5(OH)PO4 catalyst, supported on a Ni3Co1OxHy/Ni foam substrate, achieves a Faradaic efficiency of 99.0% for ammonia at a high current density of 200 mA cm−2 in 1 M nitrate electrolyte, with a production rate of 9.18 mg h−1 cm−2 and sustained stability over 200 hours. In-situ ATR-FTIR spectroscopy and density functional theory calculations elucidate a tandem mechanism: Co sites promote water dissociation to generate active hydrogen (H*), while adjacent Cu sites facilitate nitrate adsorption and subsequent hydrogenation steps. This synergistic division of labor lowers the energy barrier for the rate-determining step, effectively suppressing HER and enhancing intrinsic kinetics. The work demonstrates that precise atomic-ratio engineering in dual-site transition metal phosphates provides a viable strategy to overcome activity-selectivity trade-offs in electrocatalytic nitrate-to-ammonia conversion.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61075-X
The proliferation of electronic devices has intensified electromagnetic radiation pollution, necessitating advanced microwave absorption materials. This study presents the electrospinning fabrication of FeNiCo/carbon nanofiber (FeNiCo/CNF) composites with exceptional microwave absorption properties. The FeNiCo/CNFs achieved a minimum reflection loss (RLmin) of −55.5 dB at 14.24 GHz with an ultrathin matching thickness of only 1.6 mm. Microstructural analysis and electromagnetic parameter testing revealed that the superior absorption stems from the synergistic interaction between the carbon nanofiber network and FeNiCo alloy nanoparticles, which promotes multiple reflections and efficient energy dissipation. The precise control of coercivity and permeability via systematic modulation of magnetic metal composition enabled enhanced impedance matching and optimized magnetic-dielectric synergy. Furthermore, radar cross-section (RCS) simulations confirmed the material's capability to significantly reduce RCS values across a wide angular range, validating its potential for stealth technology applications. This work introduces a cost-effective and sustainable approach for developing ultralight, high-performance microwave absorbers, addressing the limitations of conventional materials such as high density and poor stability.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61033-X
Carbon-based materials have gained significant attention in anticancer treatment due to their exceptional biocompatibility, yet critical challenges persist in establishing definitive correlations between their porous structures and functional performance. We report the use of a silica template to guide pore formation in the design of mesoporous carbon spheres (mC) with tailored pore structures for improved combined photothermal-chemotherapy. The mesopore size of mC was adjusted by kinetic control of resin polymerization and silica hydrolysis. Structural characterization showed that 4.4 nm mesopores enabled an exceptional gemcitabine loading of 228 mg g−1 and a sustained pH/thermal dual-responsive release with >70% drug release under near-infrared (NIR) irradiation. Finite element analysis demonstrated pore size-dependent heat transfer dynamics, with the improved mC achieving a superior photothermal conversion efficiency of 62% by a combination of N-doping and defect engineering. In vitro evaluations confirmed outstanding biocompatibility with >95% cell viability at 200 μg mL−1 and potent tumor suppression in pancreatic and biliary cancer models with an ~5% cell viability at 25 μg mL−1 where combined therapy showed a 3.7-fold increased cytotoxicity over monotherapy. The improved structure of mC facilitated cascade therapeutic effects with enhanced tumor permeability derived from NIR-triggered hyperthermia and prolonged therapeutic exposure due to pH-responsive drug release. This pore engineering strategy establishes a structure-function process for next-generation theranostic platforms, addressing the critical limitations of conventional pancreatic and biliary cancer therapies through spatiotemporal control of multimodal treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3575-4
Halide perovskite memristors, known for their ion mobility, have emerged as strong candidates for computational units in next-generation memory and neuromorphic computing systems. Nevertheless, most memristors are limited to operating in a single mode, either resistive switching or threshold switching. In this work, we overcome this limitation by developing dual-mode α-formamidinium lead triiodide (α-FAPbI3) perovskite memristors with switchable volatile/nonvolatile states, enabled by engineered SnO2 electron transport layers (ETLs). Through molecular interface optimization using 3-(N,N′-dimethylmyristylammonio) propanesulfonate (Z14) and 4,4′-(1,10-phenanthroline-3,8-diyl)bis(N,N′-bis(4-methoxyphen-yl)aniline) (PNL), we achieved exceptional device stability. Volatile devices exhibited >500 switching cycles, while nonvolatile devices surpassed 1000 cycles, both maintaining a high on/off ratio (~10^3). Beyond memory applications, these devices successfully emulated biological functionalities. The volatile mode replicated four key nociceptor characteristics (threshold, relaxation, sensitization, and no adaptation), while the nonvolatile mode demonstrated advanced synaptic plasticity, including paired-pulse facilitation (PPF) and spike-timing-dependent plasticity (STDP). Capitalizing on this dual-mode synergy, we constructed a spiking neural network (SNN) for handwritten digit recognition, achieving a 93% accuracy rate—a significant milestone for perovskite-based neuromorphic systems. This study not only provides a material-level strategy for multifunctional memristor design but also bridges the gap between biological sensing and artificial intelligence, paving the way for adaptive neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3785-5
The effective separation and utilization of photo-generated carriers are critical for advancing photocatalysis, particularly in coupled reactions of H2 production and value-added chemical synthesis. Here, a sandwich-structured MnO2@ZnIn2S4@Ti3C2 hollow sphere was designed, with MnO2 and Ti3C2 loaded on the inner and outer surfaces of ZnIn2S4, respectively. MnO2 acts as an oxidation cocatalyst collecting photo-generated holes, while Ti3C2 serves as a reduction cocatalyst for electrons, promoting spatial separation of carriers and enabling spatially separated redox reactions. The hollow structure enhances light harvesting. The optimal catalyst achieves photocatalytic H2 production rate of 6.29 mmol g−1 h−1 and benzaldehyde production rate of 5.26 mmol g−1 h−1 from benzyl alcohol oxidation, significantly outperforming ZnIn2S4, MnO2@ZnIn2S4, and ZnIn2S4@Ti3C2. In situ irradiated X-ray photoelectron spectroscopy confirms effective carrier separation. In situ electron paramagnetic resonance and diffuse reflectance infrared Fourier transform spectroscopy reveal reaction intermediates. This work provides a strategy for designing efficient photocatalysts for coupled H2 production and selective oxidation.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606022
This study presents a numerical simulation of the internal flow field in a volatile organic compounds (VOCs) catalytic combustion reactor used in an enameled wire enterprise. Using ANSYS Fluent, the effects of inlet expansion section length, inlet expansion section angle, and catalyst bed spacing on the velocity field were systematically investigated. Additionally, the influence of heating tube configuration on the temperature field was analyzed. The results indicate that an expansion section length of 250 mm is optimal, balancing spatial constraints and the avoidance of recirculation zones. A zero-degree expansion angle yields the most uniform velocity distribution, though practical considerations necessitate case-specific angle selection. A catalyst bed spacing of 0.05 m satisfies the engineering requirement of maintaining pressure drop across a single catalyst layer below 200 Pa while significantly improving gas distribution within the bed. Alternating heating tubes on both sides of the reactor enhance temperature uniformity and elevate the overall catalyst bed temperature, thereby promoting efficient VOCs catalytic combustion. These findings provide quantitative guidance for reactor design optimization, contributing to improved catalytic performance and extended catalyst lifespan.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3892-2
Single-atom co-catalysts on semiconductor substrates offer a cost-efficient route to enhance photocatalytic performance with minimal precious metal loading. However, precise tuning of local coordination environments and construction of efficient single-atom co-catalysts remain challenging for overall water splitting. Here, we employ an icing-assisted photochemical reduction strategy to anchor atomically dispersed Pt species as hydrogen evolution co-catalysts on Al3+-doped SrTiO3 (Pt SA-STO). The optimized Pt SA-STO exhibits remarkable activity, with hydrogen and oxygen evolution rates of 13.62 and 6.71 mmol h−1 g−1, respectively, and a turnover frequency (TOF) of 2114.5 h−1. We pioneer the use of nuclear magnetic resonance (NMR) spectroscopy to quantitatively track the temporal evolution of Pt4+ to Pt2+ under continuous irradiation during the icing-assisted photoreduction. Advanced characterizations and theoretical calculations confirm that single-atom Pt co-catalysts facilitate directional transfer and extraction of photogenerated charge carriers, effectively suppressing surface recombination. This work provides insights into designing novel single-atom co-catalysts by deepening understanding of electronic configurations and active sites in photocatalytic overall water splitting.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60656-1
Under the carbon neutrality strategy, biomass boilers have emerged as key facilities for renewable energy utilization, yet are characterized by low-concentration SO2 emissions. Ca-based dry desulfurization presents a promising technology for biomass boiler flue gas purification due to its compact structure, low capital investment and simple operation and maintenance. However, it is generally limited by the low adsorbent utilization and insufficient desulfurization efficiency. Herein, this study developed a novel Ca-Mn composite adsorbent through a synergistic strategy integrating F127 surfactant to optimize dispersion and Mn loading to enhance oxidation efficiency. The resulting adsorbent not only significantly increased the breakthrough sulfur capacity of the Ca-based material but also markedly improved the synergistic removal of Hg0. It was demonstrated that the introduction of Mn elements and F127 effectively suppressed the agglomeration of Ca(OH)2 crystallites and induced an oxygen vacancy-rich structure, while simultaneously optimizing the pore structure of the adsorbent. The modified adsorbent exhibited the enlarged specific surface area and pore volume, which favored to enhance the reaction mass transfer and effectively prevent the pore blockage and coverage of active sites by desulfurization products. The Mn sites and oxygen vacancies formed catalytic centers, which not only accelerated the desulfurization reaction by promoting SO2 oxidation but also enabled the adsorbent to couple with Hg0 catalytic oxidation functionality. Consequently, the simultaneous removal of SO2 and Hg0 was significantly enhanced on the Ca-Mn composite adsorbent.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4097-3
The on-demand patterning of two-dimensional transition metal dichalcogenides (TMDs) with tailored edges is critical for electronic and optoelectronic applications but remains technically challenging. Here, we report a stress-guided anisotropic etching strategy for producing large-area, well-ordered MoS2 nanostructures, including nano-ribbons and nano-squares, without templates. By applying uniaxial cumulative stress followed by selective thermal etching, MoS2 monolayers are statistically etched into ribbon-like structures whose width inversely correlates with applied stress magnitude. The newly etched edges are macroscopically straight or serrated, predominantly Mo-zigzag terminated, and enhance photoluminescence by a factor of ~8.0. The edge type depends on the angle between stress direction and crystallographic orientation, corroborated by theoretical calculations. Biaxial stressing generates well-defined nano-squares, offering a scalable, versatile patterning route for engineering 2D materials with tailored functional edges, promising for electrocatalytic and optoelectronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4063-2
Quantum dot light-emitting diodes (QLEDs) are emerging as a leader in next-generation display technology. In principle, the efficiency of QLEDs is highly reliant on the radiative recombination rate of injected electrons and holes in the QD emissive layer. Within a solitary light-emitting cycle, a pre-negative-charged QD bursts into a fleeting sparkle upon encountering a hole, much like a lighted piston within a roaring engine. More pistons bring higher horsepower. The challenge of achieving highly efficient QLED lies in how to increase the number of pre-negatively charged QDs. To address these limitations, we developed a ZnO@ZnMgO core-shell nanoparticle (NP)-based electron transport layer (ETL). This design synergistically combines the high conductivity of ZnO core and the low defect density of the ZnMgO shell. Measured by electron-excited transient absorption, the average electron population (<N_e>) in the emissive layer for ZnO@ZnMgO and ZnMgO-based QLEDs was 0.61 and 0.33 at 4 V, respectively, which greatly increases the carrier recombination efficiency. As a result, green QLEDs achieve a peak EQE of 30.66%, maximum luminance of 1,615,039.85 cd/m2, and a low turn-on voltage of approximately 2 V. The T95 operational lifetime exceeded 29,000 h at 1,000 cd/m2. Currently, all parameters are at the top level within the QLED region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4123-0
Aqueous aluminum-ion batteries (AAIBs) are promising for large-scale energy storage due to safety, sustainability, and theoretical high capacity. However, sluggish electron/ion transport in conventional cathodes limits rate capability. Here, we first propose high-entropy engineering of metal oxides (HEOs) as cathodes in AAIBs, leveraging the 'cocktail effect' and abundant electron transport pathways to enhance rate-capacity. Atomic-level interactions between different metal atoms broaden the d-band with reduced electronic level degeneracy, facilitating rapid electron transport, achieving one of the best rate capabilities (119.4 mAh g−1 at 10.0 A g−1) among metal-oxide cathodes. The disordered layered oxides formed with a high-entropy framework alleviate electrostatic repulsion between aluminum ions and the fixed lattice, mitigating structural degradation and imparting excellent cycling stability (over 95.1 mAh g−1 after 500 cycles at 2.0 A g−1). The optimized HEO-Cr cathode (Fe0.6Co0.6Ni0.6Mn0.6Cr0.6O4) exhibits outstanding rate performance and cycling stability. DFT simulations and electrochemical tests reveal that multi-transition metal incorporation, bandgap narrowing, and unique lattice structure drastically enhance electron transport efficiency. The layered phase formed after cycling, based on a high-entropy framework, overcomes challenges from high charge density aluminum ions, significantly enhancing cycling stability. This work paves the way for high-performance AAIBs and other aqueous multivalent metal ion batteries by rationally designing high-entropy engineering.