SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4491-3
Magnetic tunnel junctions (MTJs) with multiferroic tunneling barriers offer a pathway to fully electrically controlled multi-state memory, addressing the high energy costs and scalability limits of magnetically controlled counterparts. In this work, we propose a theoretical design achieving four or ten distinct resistance states via electrical control, with a giant tunneling magnetoresistance (TMR) ratio of 1.1×10^4% (11000%). This value surpasses all previously reported MTJs, including experimental systems such as CoFeB/MgO/CoFeB (TMR 65%, 4 states) and theoretical systems like Ga2O3/MgO/Ga2O3 (TMR 1120%, 2 states). The multiferroic barrier enables simultaneous control of ferroelectric and magnetic order parameters, allowing reversible switching between multiple resistance levels without external magnetic fields. Our first-principles calculations reveal that the high TMR arises from spin-dependent tunneling through the barrier, modulated by the ferroelectric polarization direction and magnetization configuration. The device operates with low write energy and exhibits non-volatile retention, making it suitable for high-density storage and in-memory computing. This work establishes a new benchmark for electrically controlled MTJs and provides a practical route to overcome the limitations of current spintronic memory technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4207-0
Self-assembled monolayers (SAMs) are critical for optimizing electrode interfaces in organic solar cells (OSCs), as their molecular conformation and ordering govern interfacial quality. Conventional carbazole-based SAMs (e.g., 2PACz) rely on flexible alkyl linkers whose conformational freedom often results in disordered packing, incomplete coverage, and limited environmental robustness, especially under air processing. Here, we design and systematically study a series of well-defined carbazole SAM homologues (Cz-PPA, Cz-HPA, PCz-HPA, and PCz-PPA) to elucidate the role of synergistic conformational locking achieved through linker rigidification and terminal conjugation extension. PCz-HPA, which integrates a rigid cyclohexane linker with a strongly conjugated 3,6-diphenylcarbazole end group, enables effective conformational locking. It forms a highly ordered, densely packed monolayer on ITO, delivering high surface coverage, a strengthened interfacial dipole, and improved energy-level alignment. The rigid framework and ordered interface enhance air-process stability and interfacial contact, thereby suppressing recombination and facilitating exciton dissociation and charge collection. Using PCz-HPA as SAM for the devices based on PM6:L8-BO reaches 19.75% efficiency and it demonstrates consistent gains across multiple systems. These results identify conformational locking via linker rigidification as a general design rule for durable, high-performance SAM interlayers in organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4183-3
Excessive ultraviolet (UV) radiation poses significant risks to human health, necessitating highly sensitive detection systems. Organic photodetectors (OPDs) offer high sensitivity and tunable spectral response, but their UV performance is constrained by conventional glass/indium tin oxide (ITO) substrates and electrodes, and insufficient photoactive layer responsivity. Here, we report high-performance UV-OPDs achieved through UV-transparent window and active-layer optimization. Replacing glass/ITO with a UV-transparent window comprising a quartz substrate and PH1000 electrode enhances UV transmittance. Integrating the high UV-responsive blend PM6:Y6:PC71BM as the active layer, the optimal ternary UV-OPD exhibits external quantum efficiency (EQE) exceeding 53% across 280–400 nm, with a peak EQE of 78.29% and responsivity of 214.68 mA/W at 340 nm, alongside a rapid response time of 2.6/2.1 μs. This performance represents the best combination of responsivity and response time reported to date in the UV region. We demonstrate the potential of these UV-OPDs for outdoor real-time UV monitoring. This work presents a promising strategy for developing high-performance UV-OPDs through transparent substrate and electrode engineering, and active-layer optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3697-8
Multi-site coupling is a promising strategy for developing highly efficient and CO-resistant hydrogen oxidation reaction (HOR) catalysts for proton exchange membrane fuel cells (PEMFCs). However, designing multifunctional synergistic schemes for single-atom sites remains a significant challenge. Herein, we propose a dual-template-confined oxophilic engineering strategy to construct well-dispersed iridium-nickel (IrNi) atomic dimers adjacent to IrNi nanoclusters on porous nitrogen-doped carbon (IrNi Dimer/NC1.8-PNC). The paired IrNi dimer features an asymmetric Ir-N3 configuration coordinated with heteroatomic Ni-N3O via an N-bridge. Remarkably, IrNi Dimer/NC1.8-PNC exhibits a ~23-fold enhancement in mass activity (4.36 A mg−1 Ir at 20 mV) and 5-fold longer stability compared to benchmarking Pt/C toward HOR, while achieving a high rated power density of 1.18 W cm−2 in PEMFC anode applications. Furthermore, IrNi Dimer/NC1.8-PNC demonstrates superior CO tolerance over monometallic Ir and Pt/C in both half-cell and full-cell devices. Combined experimental and density functional theory studies reveal that oxophilic Ni modulates the electronic environment of Ir through alloying and dimer interactions, thereby enhancing HOR activity. Importantly, the asymmetric IrNi dimer enables efficient CO* and OH* co-adsorption while facilitating CO2* desorption, synergistically mitigating CO poisoning and improving atom utilization efficiency. This work provides a design strategy and fundamental insights for multi-site synergistic catalysts in PEMFC anodes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010302
Cadmium (Cd) contamination of agricultural soils poses significant economic and health risks. While extensive research has focused on Cd accumulation in staple crops like rice, data on oilseed crops remain scarce, hindering safety assessments of edible oils and oilseed meals. This study investigated Cd accumulation and translocation in rapeseed (Brassica napus) grown in You County, Hunan Province, a region severely contaminated with Cd. Rhizosphere soil and plant tissues (roots, stems, seeds) were collected and analyzed for Cd concentrations. Results showed that approximately 71% of rhizosphere soil samples exceeded the agricultural soil pollution risk screening value for Cd, indicating high ecological risk. Cd concentrations in roots and stems were (0.49 ± 0.39) mg·kg⁻¹ and (0.54 ± 0.31) mg·kg⁻¹, respectively, comparable to or higher than soil Cd levels (0.51 ± 0.31) mg·kg⁻¹, with elevated bioaccumulation and translocation factors. This suggests that improper disposal of rapeseed roots and stems, such as returning them to fields or burning, could lead to secondary Cd pollution. In contrast, Cd bioaccumulation and translocation factors in seeds were less than 1, and Cd concentrations in seeds, oil, and oilseed meals were relatively low. Comparative analysis with sesame, camellia oleifera, and peanut indicated that rapeseed-derived oil and meal contain lower Cd levels, positioning rapeseed as a promising low-Cd-accumulating edible oil crop for cultivation in Cd-contaminated areas.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010203
The production and disposal of lithium batteries release not only hazardous metals and particulates but also substantial amounts of harmful organic pollutants. This study focuses on N-methyl-2-pyrrolidone (NMP) to investigate the environmental release and human exposure of organic pollutants throughout the lithium battery lifecycle. Using liquid chromatography-high-resolution mass spectrometry (LC-HRMS), NMP was quantified in environmental samples from battery production and dismantling facilities, as well as in pyrolysis products from simulated thermal recovery of mainstream lithium batteries. Key release stages were identified: slurry mixing and coating/drying during production; shredding, electrolyte volatilization, and high-temperature pyrolysis during disposal. In unprotected occupational settings, estimated NMP exposure via dust ingestion exceeded reference doses, underscoring the need for health impact assessments and evaluation of protective measures. This research provides critical insights into the environmental release and population exposure of organic pollutants across the lithium battery lifecycle, informing health policy for vulnerable populations.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604005
To elucidate the effects of exogenous antibiotic-resistant bacteria (ARB) exposure on wheat growth and associated bacterial community assembly, the inhibitory impacts of exogenous ARB on wheat seedling root and shoot length, shifts in root endophytic and rhizosphere bacterial communities, and the horizontal transfer of exogenous antibiotic resistance genes (ARGs) to indigenous endophytic bacteria were investigated using plate culture counting and 16S rRNA high-throughput sequencing. The results showed that exogenous ARB exposure significantly suppressed wheat seedling root and shoot growth, with inhibition rates increasing in an ARB concentration-dependent manner. At an exogenous ARB concentration of 108 CFU/mL, the inhibition rates of seedling root and shoot length reached 68.83% and 36.87%, respectively. During the period of ARB exposure, the relative abundance of Clostridium_sensu_stricto_5 in root endophytic bacteria increased rapidly, becoming the most dominant genus (45.02%) by the end of the exposure period. In contrast, Betaproteobacteriales remained the dominant order in the rhizosphere bacterial community throughout the experiment, with its relative abundance increasing continuously over time. The proportion of ARB-carrying endophytic bacteria initially decreased and then increased during exposure, showing a significant positive correlation with the relative abundances of Clostridium_sensu_stricto_5, Clostridium_sensu_stricto_1, Bacillus, and Paenibacillus (P<0.05). In summary, exogenous ARB exposure significantly inhibits wheat seedling growth and alters the community structure of both root endophytic and rhizosphere bacteria. Sustained ARB exposure leads to the transfer of exogenous ARGs to root endophytes, and Clostridium_sensu_stricto species may act as potential hosts for ARGs in wheat seedling roots.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225227
Imidazolium-based ionic liquids (ILs) are foundational materials in sustainable chemical engineering due to their negligible volatility, exceptional thermal stability, and tunable properties. This study details the development, optimization, and analysis of an industrial-scale green synthesis pathway for 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) via quaternization of N-methylimidazole with 1-chlorobutane. Reaction parameters were optimized using orthogonal experimental design, and process intensification strategies were implemented to enhance efficiency and environmental sustainability. The optimal conditions were identified as a reaction temperature of 76 °C, a molar ratio of N-methylimidazole to 1-chlorobutane of 1:1.3, and a reaction time of 36 h, achieving a single-pass yield of 95.6%. Kinetic studies revealed a significant correlation between temperature, molar ratio, and conversion efficiency, with an activation energy (Ea) of approximately 135.7 kJ/mol, indicating pronounced temperature dependence. A closed-loop material recycling system was designed, enabling recovery rates of 99.5% for 1-chlorobutane and 98.1% for ethyl acetate, thereby curtailing raw material consumption and waste generation. This approach aligns with green chemistry principles and propels the process toward near-zero emissions. The pathway offers a scalable model for [Bmim]Cl manufacture and a transferable strategy for synthesizing other ionic liquids, representing a substantial advancement in sustainable process engineering.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605018
To address the inadequacy of existing temporal emission allocation coefficients for oil storage, transportation, and sales sources in regions with distinct seasonal temperature variations, this study focused on a large oil depot in Northwest China. A method for establishing temperature-dependent hourly allocation coefficients for VOCs emissions was proposed, revealing a positive correlation between ambient temperature and emission coefficients. The coefficient peaked at 0.068 when temperatures exceeded 14 °C and dropped to a minimum of 0.007 below 8.5 °C. Annual VOCs emissions totaled 256.13 t, with summer contributing 108.89 t (42.51% of annual total) and winter only 12.54 t (4.90%), making summer emissions approximately 8.68 times higher than winter. Using CALPUFF dispersion modeling, dynamic source strength scenarios produced a maximum hourly concentration of 2242.7 μg/m³, a 55.12% increase over the constant source strength scenario (1445.8 μg/m³). The area of exceedance increased by 0.03 km², and the atmospheric environmental protection distance extended by 450 m, from 0 m to 450 m. These results demonstrate that conventional constant emission assumptions underestimate peak concentrations and protection distances, posing health risks to nearby residents. The study provides a scientific basis for localized emission regulation and improved environmental protection distance calculations.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225162
The effects of tempering temperature on the microstructure, strength-toughness balance, and precipitates of a quenched Cu-Cr-Ni ultra-high strength weathering steel were systematically investigated. The steel was austenitized at 920°C, quenched, and then tempered at 500°C, 550°C, and 600°C. Microstructural characterization was performed using optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), while mechanical properties were evaluated via tensile and low-temperature impact tests. Results showed that as the tempering temperature increased from 500°C to 600°C, the microstructure transformed from lath-shaped tempered sorbite to a non-lath morphology. The fraction of rod-like cementite decreased, while spheroidized cementite increased, and the size of MC (M = Ti, Nb, V, Mo) precipitates decreased from an average of 12.2 nm to 9.9 nm. Consequently, yield strength and tensile strength decreased from 935 MPa and 958 MPa to 866 MPa and 888 MPa, respectively, whereas total elongation and impact energy at -40°C increased continuously, reaching maximum values of 5.0% and 280 J at 600°C. When tempered at 550°C, the steel exhibited a yield strength of 895 MPa, tensile strength of 921 MPa, elongation of 4.3%, and impact energy of 271 J at -40°C, demonstrating an optimal combination of strength and toughness. This improvement is primarily attributed to the spheroidization of cementite and the uniform dispersion of fine MC precipitates, which alleviate stress concentration, along with the softening of the acicular ferrite matrix during tempering.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511090
In ecological restoration projects such as wetland reconstruction and mine reclamation, seedling transplantation or mechanical damage often leads to slow healing, reducing survival rates and weakening carbon sequestration and soil-water conservation functions. To address secondary pollution from traditional chemical remediation, this study developed a self-powered piezoelectric hydrogel for green electrical stimulation of plant wounds. The hydrogel, based on polyacrylamide/polyethylene glycol (PAM/PEG) with CaCl2, formed a microporous, locally ordered piezoionic network. Characterization included microstructure, piezoionic response, and water retention. At 30 °C and 55% relative humidity, the hydrogel retained about 70% mass after 80 h of continuous water loss. Under simulated environmental mechanical forces, the hydrogel generated a peak voltage of approximately 6 mV. In tomato seedling stem models, wound callus area ratios reached approximately 49.50%, 64.87%, and 86.13% at 3, 5, and 10 days, respectively, when the hydrogel was attached and driven by environmental forces. The PAM/PEG/CaCl2 hydrogel efficiently converts environmental mechanical energy into mild electrical signals, promoting plant wound healing, reducing exogenous chemical use, and offering a low-carbon, environmentally friendly material pathway for ecological restoration and urban green space management.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0031
The high-temperature behavior of biomass ash critically influences gasifier operational efficiency. This study investigates the differential high-temperature behaviors of corn straw ash (CSA) and wheat straw ash (WSA) using an intelligent ash fusion analyzer, high-temperature rotating viscometer, X-ray diffraction (XRD), SEM-EDS, and FactSage thermodynamic simulations. Both ashes contain high K2O (>30%) and exhibit flow temperatures below 1300 °C. Despite higher K2O and lower SiO2, CSA exhibits a higher flow temperature (1241 °C) than WSA, attributed to elevated CaO (10.39%) and MgO (7.33%) that promote formation of high-melting silicates (K2MgSiO4, K2Ca2Si2O7, CaSiO3). In contrast, WSA with lower CaO (4.92%) and MgO (2.82%) tends to form low-melting potassium silicates. At high temperatures, both slags are typical crystalline slags, with viscosity rising sharply below a critical temperature. For CSA, rapid nucleation and coarsening of silicate crystals (e.g., KAlSiO4 grain size increases from 20.5 nm at 1350 °C to 192.9 nm at 1050 °C) cause abrupt viscosity increase. For WSA, a high P2O5 content (10.05%) induces a 'chemical dilution effect', leading to persistent KAlSiO4 during cooling and elevated viscosity, especially at the final cooling stage. This study elucidates how ash chemical composition governs high-temperature phase equilibrium and non-equilibrium kinetics, thereby macroscopically affecting ash fusion and rheological behavior, providing a theoretical basis for deeper understanding of biomass ash high-temperature characteristics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025120801
The interaction between microplastic-derived dissolved organic matter (PSDOM) and iron oxides in soil environments can modulate its photosensitization effects, yet the underlying mechanisms remain elusive. This study investigated the influence of hematite with distinct morphologies—flake-shaped (HNPs) and cubic (HNCs)—on the photosensitization of polystyrene-derived dissolved organic matter (PSDOM). Under 500 W mercury lamp irradiation, both hematite morphologies promoted PSDOM degradation, with HNCs exhibiting superior performance: total organic carbon (TOC) decreased from 18.4 mg·L−1 to 12.3 mg·L−1 within 90 min, compared to 13.3 mg·L−1 for HNPs. Three-dimensional fluorescence spectroscopy indicated that hematite alters the humification process, thereby modifying photosensitization. Electron paramagnetic resonance (EPR) spectroscopy identified the generation of singlet oxygen (1O2), hydroxyl radicals (·OH), and carbon-centered radicals (CH3C(=O)OO·). HNCs significantly enhanced 1O2 production, while HNPs favored ·OH generation; both inhibited CH3C(=O)OO· formation. Quantitative analysis via high-performance liquid chromatography revealed that the steady-state concentration of 1O2 was highest with HNCs, reaching 2.80 times that of the PSDOM control, whereas ·OH concentration peaked with HNPs at 1.98 times the control. Notably, the steady-state concentration of 1O2 was approximately three orders of magnitude higher than that of ·OH. These findings elucidate the morphology-dependent role of hematite in PSDOM photosensitization, providing mechanistic insights into the environmental fate of microplastic-derived organic matter in complex soil systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030403
Microplastics (MPs) act as vectors for co-migrating antibiotics and heavy metals, forming complex pollution systems with potential joint toxicity. However, the differential adsorption behaviors and underlying mechanisms of MPs toward organic versus inorganic pollutants remain insufficiently understood. This study selected polypropylene (PP) microplastics, a major component of agricultural plastic films, and investigated the adsorption of sulfamethoxazole (SMX) and Cr(VI) onto aged PP under varying environmental conditions. Results demonstrated that aging increased the maximum adsorption capacity by 2–3 times for both pollutants. Notably, aged PP exhibited approximately 30 times higher adsorption capacity for SMX than for Cr(VI). Characterization revealed that aging introduced oxygen-containing functional groups (e.g., carbonyl) on the MP surface, enhancing adsorption. Mechanistic analysis indicated that hydrogen bonding and electrostatic interactions dominated SMX adsorption, while Cr(VI) adsorption was primarily governed by electrostatic interactions and pore-filling. The stronger intermolecular forces for SMX compared to reversible pore-filling for Cr(VI) explained the observed differences. Increasing pH induced electrostatic repulsion, reducing adsorption of both pollutants. High concentrations of Na+ and Mg2+ caused charge shielding, potentially enhancing Cr(VI) adsorption but inhibiting SMX adsorption due to competition for active sites. The presence of organic matter (humic acid) had negligible effects on Cr(VI) adsorption but reduced SMX adsorption, likely due to complexation. These findings elucidate distinct molecular-level pathways for organic versus inorganic pollutant adsorption on aged MPs, highlighting the roles of hydrogen bonding and pore-filling in driving differential behaviors.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022704
Secondary inorganic aerosols (SNA), comprising sulfate, nitrate, and ammonium, are critical contributors to PM2.5 pollution in the Fenwei Plain, yet their formation mechanisms remain poorly characterized. Wintertime observations in Taiyuan revealed SNA as the dominant PM2.5 component, with a mean mass concentration of 33.19 ± 18.72 μg m−3, accounting for 47.13% of total PM2.5 mass. SNA concentrations increased markedly with pollution severity, but even under relatively clean conditions, SNA maintained a high mass fraction. Diurnal variation and correlation analyses indicated that nitrate formation pathways differed between day and night, largely governed by relative humidity (RH). During daytime, high RH (>55%) facilitated the partitioning of gaseous HNO3 to particulate nitrate. At night, RH positively correlated with nitrate concentration and nitrogen oxidation rate (NOR), with increased aerosol liquid water content (AWC) promoting NO2-to-nitrate conversion. The PM2.5 pH ranged from 4.3 to 5.2, and sulfate formation was primarily driven by H2O2 oxidation, with NO2 oxidation as a secondary pathway. These findings enhance understanding of SNA formation in the Fenwei Plain and provide a scientific basis for air quality policy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3799-4
Li-rich layered oxides (LLOs) xLi2MnO3·(1−x)LiTMO2 (0 < x < 1, TM = Mn, Ni, Co, etc.) are promising high-energy cathode materials for lithium-ion batteries, capable of achieving energy densities up to 1000 Wh kg−1. However, their practical application is hindered by limited cycle life and voltage decay, primarily stemming from structural instability of Li2MnO3 and LiTMO2 domains during cycling, which manifests as transition metal cation migration, oxygen release, and TM dissolution. This review establishes a comprehensive design and modification scheme based on the fundamental structural unit of LLOs: the LiMn6 hexatomic-ring. In this unit, each Li atom in the TM layer is surrounded by six Mn atoms, forming a π-type hybridization between Mn 3d(t2g) and O 2p orbitals, creating an intact π-bond ring that acts as a distributed redox center. Ordering these functional units into specific spatial configurations can enhance capacity, voltage, and structural stability. However, substituting Mn with other elements breaks the symmetry of the π-bond ring, altering redox behavior and reversibility. The spatial arrangement of LiMn6 rings, representing the arrangement of π-bond rings, is critical for redox activity. In Li2MnO3, the typical honeycomb superstructure of LiMn6 rings is discussed. This review highlights the importance of functional unit ordering in material design, drawing parallels from other systems, and proposes a systematic approach to engineer LLOs for improved electrochemical performance.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202505108
Open-pit mining in high-cold regions causes severe ecological degradation, including vegetation loss, soil structure destruction, and frequent freeze-thaw disturbances, complicating ecosystem recovery. This review systematically synthesizes the current status, theories, and key restoration technologies for degraded ecosystems in high-cold mining areas. Comparative analysis with typical high-cold degraded ecosystems worldwide reveals that high-cold mining areas face challenges such as frequent freeze-thaw cycles, hydrological disruption, wind erosion, and difficult vegetation establishment. We propose strengthening aboveground-belowground synergistic restoration: (1) aboveground restoration should focus on screening cold-resistant native plants and optimizing mixed community configurations, combined with plant growth-promoting multi-microbial consortia to facilitate vegetation recovery; (2) belowground restoration should be based on engineering soil profile reconstruction, integrating physical-chemical-biological multi-dimensional remediation techniques to achieve aboveground and belowground community reconstruction and functional recovery; (3) a progressive restoration framework is established, with short-term goals targeting soil stabilization and structure improvement, medium-term goals focusing on constructing multifunctional plant-soil communities, and long-term goals achieving self-sustaining, maintenance-free restored ecosystems. Finally, addressing the unclear mechanisms of aboveground-belowground synergistic interactions and insufficient environmental adaptability of restoration technologies, two prospects are proposed: (1) deepening research on aboveground-belowground synergistic mechanisms to reveal interactions between cold-tolerant microorganisms and plants; (2) advancing the development of characteristic restoration technologies adapted to high-cold environments.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60695-0
The direct carbonylation of glycerol with CO2 to glycerol carbonate represents a promising route for CO2 utilization, addressing both carbon emission reduction and the synthesis of value-added chemicals. However, the reaction is thermodynamically limited, resulting in low glycerol conversion, necessitating the use of coupling agents and appropriate catalysts. This review systematically examines recent progress in homogeneous catalysts (inorganic and organic bases) and heterogeneous catalysts (Zn, Cu, Ce, La, Mg, noble metals, modified zeolites, non-metallic materials) for this transformation. Strategies such as metal oxide modification, support optimization, precursor selection, and construction of acidic-basic sites are analyzed for enhancing catalytic performance. The effects of coupling agents including acetonitrile, adiponitrile, 2-cyanopyridine, MgCO3, CaC2, and NaHCO3 are summarized. Notably, 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU), Zn(QTf)2, and metal composite oxides like ZnO-CeO2 have demonstrated promising catalytic performance. Future research directions include developing organometallic complexes or composite metal oxides with highly dispersed active sites and tailored morphologies to modulate surface area, pore size, and acidity/basicity; optimizing coupling agents or designing novel membrane reactors to improve glycerol conversion; and introducing polar solvents to enhance reactant adsorption and activation. These approaches provide valuable references for catalyst design and reaction system optimization in the carbonylation of glycerol with CO2.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3906-2
Achieving flexible polymer-based organic afterglow materials with color-tunable and stimulus-responsive capabilities is significant in diverse optoelectronic fields, especially in next-generation wearable full-color display applications, yet remains a great challenge. Here, we report polymer-based dual-mode afterglow systems that realize long-lived color-tunable afterglow with full-color gamut of blue, green, orange, red, and even white-light emissions with ultralong lifetimes up to 2.42 s. This unique performance is enabled by a universal strategy of dual-mode afterglow-assisted Förster resonance energy transfer (FRET) that utilizes seconds-long dual-mode afterglow materials as energy donors and permits efficient synchronous transfer of singlet and triplet excitons from energy donors to the fluorescent dye acceptors. More impressively, the dual-mode afterglow-assisted FRET efficiency reaches up to 99%, with the lifetime of the energy acceptor reaching 1.55 s. Associated with the abundant hydrogen-bonding interactions within the polymer system, the doped afterglow films exhibit water/thermal stimulus responsiveness and recyclability. Furthermore, these full-color dual-mode afterglow materials are employed for multicolor screen-printing, optical anti-counterfeiting, and high-level information encryption, demonstrating considerable application potential in advanced anti-counterfeiting technologies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512052
Constructed wetlands (CWs) with conventional substrates often exhibit limited removal of nitrogen and antibiotics from secondary effluent. This study developed an iron-carbon-manganese ore (Fe-C-Mn) composite substrate CW to enhance simultaneous removal of nitrogen and tetracycline (TC). Under influent TC of 2 mg·L−1 and total nitrogen (TN) of 15 mg·L−1, the Fe-C-Mn system achieved average TC removal of 91.3%, significantly higher than the gravel control (27.2%). TN and nitrate nitrogen (NO3−-N) removals reached 71.7% and 83.3%, respectively, versus 7.8% and 1.2% in the control. Substrate analysis revealed increased surface roughness and synergistic generation of active components (Fe(II)/Fe(III) and Mn(II)), driving autotrophic denitrification and TC biodegradation/chemical degradation. Microbial community analysis indicated reduced overall diversity but selective enrichment of potential TC degraders (e.g., Trichosporon, Bacillota) and denitrifiers (e.g., unclassified_f_Rhodocyclaceae). TC degradation pathways included demethylation, hydroxylation, and ring-opening, ultimately yielding small metabolites. These findings provide theoretical and technical support for enhanced removal of antibiotics and nitrogen from secondary effluent using CWs.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512014
Mining activities cause severe soil degradation and microbial diversity loss, impeding ecological restoration. This study evaluated the effects of a novel soil amendment, microporous bio-gravel (MBG), on bacterial and fungal community structure and function in degraded soil from the Baiyinhua open-pit mine, Inner Mongolia. A pot experiment with four MBG-to-soil volume ratios (CK, L=1:3, M=1:2, H=1:1) was conducted, with a simplified plant community and uniform fertilization. After 180 days, soil samples were analyzed via high-throughput sequencing and bioinformatics. Results showed that the medium ratio (M) significantly increased fungal Shannon index and evenness, while the high ratio (H) negatively affected bacterial communities. At phylum and genus levels, MBG promoted enrichment of Cyanobacteria and specific functional groups (e.g., nitrogen-fixing bacteria, Bacillus). Co-occurrence network analysis revealed peak complexity, modularity, and average degree in bacterial and fungal networks under the M treatment. Functional prediction indicated significant enrichment of pathways related to lipopolysaccharide biosynthesis, nitrotoluene degradation, and plant-pathogen interactions, alongside increased abundance of saprotrophic and ectomycorrhizal fungi. Mantel and VPA analyses showed that MBG indirectly regulated microbial community structure by improving soil physicochemical properties and plant traits, with stronger effects on fungi than bacteria. In conclusion, MBG optimizes the soil microhabitat and plant-soil-microbe interactions, modulating microbial diversity, network complexity, and functional potential. The medium ratio (1:2) was most effective, demonstrating potential for ecological restoration of degraded mine soils.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4013-y
Multicolor fluorescent polymer materials (MFPMs) are of significant value in biomaterials and display technologies due to their rich color palette. Traditional construction methods rely on incorporating multiple fluorescent molecules of different colors, which introduces complexities in structural design, synthesis, purification, and practical operability. To overcome these challenges, a strategy employing a single fluorophore that exhibits multiple fluorescent colors has been developed and integrated into MFPMs. This approach has advanced fields such as information anti-counterfeiting and optoelectronic materials. This review summarizes recent developments in MFPMs based on a single fluorescent molecule, elucidates preparation methods and color conversion mechanisms, and analyzes application prospects. Key mechanisms include aggregation-induced emission (AIE), excited-state intramolecular proton transfer (ESIPT), and twisted intramolecular charge transfer (TICT), which enable color tuning through environmental stimuli or assembly. The review highlights the potential of this strategy to simplify fabrication processes while achieving tunable emission colors. It provides guidance for designing novel multicolor fluorescent materials and fosters progress in fluorescent materials, polymer science, and materials science.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4109-2
The fabrication of high-efficiency organic solar cells (OSCs) under ambient conditions remains a formidable challenge due to the sensitivity of active layer morphology to environmental factors. We propose an innovative approach for air-processed devices that combines spontaneous water-spreading film formation with layer-by-layer (LBL) deposition. This method enables the fabrication of donor- and acceptor-dominant bulk heterojunction blend films near the anode and cathode interfacial layers, respectively, optimizing vertical phase separation and enhancing charge transfer efficiency. In the D18:L8-BO system, the device achieves a power conversion efficiency (PCE) of 19.02% with an exceptionally narrow efficiency distribution. Even for devices with an area of 1 cm2, a PCE of 16.56% is attained. After a 1000-hour decay test, the efficiency retains 84.1%. This novel method offers a promising pathway for advancing the industrial application of large-area, highly stable devices with narrow efficiency distribution under ambient conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4072-3
All-inorganic, hole-transport-material-free (HTM-free), carbon-based perovskite solar cells (C-PSCs) have attracted significant attention due to their exceptional stability and low cost. However, their performance and commercial potential are constrained by poor interfacial contact, insufficient crystallinity, and energy level misalignment. In this work, we address these challenges via a molecular engineering strategy by introducing tetrakis(4-ethynylphenyl)methane (TEPM) as a multifunctional additive. The alkynyl moiety (C≡C) in TEPM coordinates with Pb2+ ions in perovskite precursors, synergistically slowing crystallization kinetics to regulate crystal growth and passivate deep-level defects. Consequently, CsPbI3 films exhibit larger grain sizes, improved crystallinity, and lower defect densities. Devices modified with TEPM achieved a record power conversion efficiency (PCE) of 20.01% (certified 19.58%). Additionally, unencapsulated devices retained 87.6% of their initial efficiency after 1080 h under ambient conditions (25 °C, 30% relative humidity), and maintained 94.0% of their initial efficiency after 730 h of continuous AM 1.5G illumination in air. This work sets a new efficiency benchmark for inorganic HTM-free C-PSCs and provides a versatile molecular engineering strategy for developing high-performance, stable perovskite photovoltaics.