SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3637-6
Traditional optical fiber communication encryption methods lack sufficient dynamic adaptability and hardware flexibility, while reconfigurable logic gates can overcome this limitation, thereby significantly improving the flexibility of encryption systems. This study reports a reconfigurable optoelectronic logic gate (OELG) system based on hafnium-zirconium oxide (HZO) ferroelectric thin films. Through ultra-low temperature atomic layer deposition technique, the fabricated HZO thin films demonstrate an exceptional pyroelectric coefficient of 1835.91 μC m−2 K−1 and robust multi-level polarization stability, enabling efficient broadband photon-to-current conversion. By leveraging the pyroelectric effect and tunable polarization states, the OELG device achieves dynamic optical signal modulation and logic processing. The OELG device supports five fundamental logic operations (AND, OR, NAND, NOR, NOT) via electrical bias and polarization control, without requiring hardware modifications. The OELG device demonstrates stable performance over 10^9 cycles with no degradation, meeting practical application requirements. Furthermore, a convolutional neural network (CNN)-integrated image encryption-decryption framework was validated, achieving 95.01% recognition accuracy on decrypted data, while unauthorized decryption attempts resulted in significant feature loss. This study addresses security challenges in optical communication networks by proposing an innovative solution that integrates pyroelectric materials with reconfigurable logic gate technology, offering a new pathway to enhance physical-layer security.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3719-8
The proliferation of 5G communications and smart electronic devices has intensified electromagnetic wave (EMW) pollution, necessitating microwave absorption materials (MAMs) with high efficiency, lightweight, and flexibility. Traditional MAMs suffer from high density and narrow effective absorption bandwidth (EAB). This work presents a lightweight, flexible microwave-absorbing composite fabricated by in-situ polymerization foaming of polyurethane (PU) with multi-walled carbon nanotubes (MWCNTs) and flaky carbonyl iron (FCI). The hierarchical PU composite foam, designated 3*PFC 0.5-1.0-1.5, achieves an EAB of 15.7 GHz, covering 98.1% of the tested 2–18 GHz range, including S, C, X, and Ku bands. This performance stems from synergistic conductive and magnetic losses, along with impedance matching facilitated by the hierarchical porous structure. The composite maintains low density and high compressibility, offering a promising solution for EMW absorption in 5G, military stealth, and smart devices. The in-situ method ensures strong interfacial adhesion between fillers and matrix, enhancing durability compared to impregnation methods. This study demonstrates a scalable approach to fabricate high-performance MAMs with broad bandwidth and mechanical robustness.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3767-9
Progressive skin fibrosis ultimately results in irreversible contractures, causing both joint dysfunction and cosmetic deformity. The key pathological features of skin fibrosis include persistent inflammation and abnormal accumulation of the extracellular matrix (ECM), with epithelial-mesenchymal transition (EMT) playing a critical role in disease progression. However, current therapeutic strategies for cutaneous fibrosis are largely palliative and often require repeated interventions, with limited efficacy. Celastrol (Cel) exerts anti-inflammatory and anti-fibrotic effects in skin tissue, but its clinical application is limited by poor bioavailability and a narrow therapeutic window. Tetrahedral framework nucleic acid (tFNA), a novel nanocarrier system, exhibits multiple advantages, including enhanced cellular uptake, improved cell viability, and intrinsic anti-fibrotic and anti-inflammatory properties. Therefore, this study applied tFNA-Cel complex (TCC) as an advanced nanotherapeutic agent, designed to exert a synergistic anti-fibrotic effect. In this study, an in vitro model of skin fibrosis was established using human keratinocyte (HaCaT) cells treated with 5 ng mL−1 transforming growth factor beta (TGF-β) for 24 h. The results showed that TCC significantly inhibited EMT progression by reducing α-smooth muscle actin (α-SMA) levels and increasing E-cadherin level. Compared to tFNA or Cel alone, TCC exhibited superior anti-fibrotic effects in the fibrosis model, as evidenced by modulation of SMAD family member 2 (SMAD2) signaling and collagen I expression. Furthermore, the TCC group showed lower levels of nuclear factor κB p65 (NF-κB p65), BCL-2-associated X protein (Bax), and reactive oxygen species (ROS) compared to the Cel or tFNA groups. These findings highlight TCC as a promising treatment for skin fibrosis, with its synergistic anti-fibrotic effects providing new therapeutic avenues.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507058
With the rapid development of China's lithium-ion power battery industry, the recycling of large-scale retired batteries has become a critical link for the sustainable development of the new energy vehicle industry. The recovery of cathode materials from spent lithium iron phosphate (LiFePO4) batteries is a current research hotspot, significant for resource recycling and environmental protection. This study systematically reviews recent progress in recycling technologies for spent LiFePO4 cathode materials, mainly including direct regeneration, pyrometallurgy, and hydrometallurgy. It focuses on analyzing the current research status of key steps in hydrometallurgy, such as leaching of valuable elements, deep removal of impurities, and product regeneration, and compares the advantages and limitations of various methods. Addressing core issues in current recovery processes, such as insufficient high-value utilization of iron and phosphorus resources and difficulty in deep impurity removal, this study proposes corresponding solutions and technical prospects, aiming to provide theoretical reference and engineering guidance for efficient, clean, and high-value recycling of spent LiFePO4 batteries.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605014
Chlorinated aliphatic hydrocarbons (CAHs) are prevalent groundwater contaminants at industrial sites in China. This pilot-scale study evaluated in-situ anaerobic bioremediation of CAHs-contaminated groundwater in a low-permeability bedrock fracture zone at depths up to 40 m. A self-developed anaerobic dechlorinating culture (BS-1), containing Dehalococcoides, Desulfitobacterium, and Dehalogenimonas, was injected alongside carbon sources (sodium citrate and emulsified vegetable oil) and nutrients. Pressurized nitrogen gas injection enhanced the distribution of amendments, achieving a radius of influence of 5.0 m. Over 399 days of monitoring, the combined use of slow-release and soluble carbon sources maintained anaerobic conditions (ORP < -100 mV) for over one year, providing sustained electron donors. The emulsified vegetable oil reduced injection frequency and operational costs. The BS-1 culture effectively dechlorinated vinyl chloride, cis-1,2-dichloroethylene, trichloroethylene, and chloroform, achieving removal efficiencies exceeding 95%. At times, groundwater quality met the Class IV standard of GB/T 14848-2017. This study demonstrates a green, economical, and effective solution for CAH-contaminated site remediation, with significant engineering application potential.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506080
Thallium (Tl) is a highly toxic trace heavy metal, posing severe risks to human health and the environment. Cement kilns are significant sources of gaseous Tl emissions, with concentrations up to 25 μg·m−3, which can poison SCR catalysts and cause environmental contamination. This study developed MnO2/γ-Al2O3 adsorbents via wet impregnation with varying Mn loadings (0–15 wt%) to capture gaseous TlCl. Fixed-bed adsorption experiments at 300 °C with 20% O2 revealed that capture capacity initially increased with Mn loading, peaking at 10 wt% MnO2 (10MnO2/γ-Al2O3), then declined at 15 wt%. Characterization (XRD, O2-TPD, H2-TPR) indicated that Mn species enhanced redox properties, oxidizing Tl+ to Tl3+ and immobilizing it on the surface. DFT calculations showed that TlCl forms stronger Al–Cl and Mn–Cl bonds on MnO2/γ-Al2O3 than on γ-Al2O3, with higher adsorption energy and greater charge transfer, corroborating experimental results. The optimal adsorbent, 10MnO2/γ-Al2O3, demonstrates superior Tl capture performance, offering a promising upstream solution for protecting SCR catalysts and reducing atmospheric Tl emissions from cement kilns.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509031
This study establishes a carbon footprint calculation method and an environmental benefit assessment model for the dismantling process of waste televisions (TVs) based on life cycle assessment (LCA). Activity data on energy consumption and material flows were collected from typical treatment enterprises via field investigation. The ReCiPe 2016 model was applied to quantify midpoint and endpoint environmental impacts. Results show that the dismantling and recycling process yields net environmental benefits in most impact categories. At the midpoint level, significant reductions were observed in fossil resource scarcity (−26,494.23 kg oil eq), freshwater ecotoxicity (−2.21×10^4 kg 1,4-DCB), and greenhouse gas emissions (−956.53 kg CO2 eq). At the endpoint level, reductions in human health damage (−1.59×10^4 DALY), ecosystem damage (−2.35×10^4 species·yr), and resource depletion costs (−4.22×10^4 USD) were achieved. Carbon footprint analysis indicates that the carbon footprint per TV ranges from 0.231 to 0.247 kg CO2 eq per unit, with electricity consumption as the dominant emission source. Sensitivity analysis reveals that electricity consumption significantly influences the carbon footprint. Finally, emission reduction recommendations are proposed from aspects of equipment upgrade and energy management, providing theoretical basis and practical guidance for low-carbon treatment of electronic waste.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607002
In municipal solid waste (MSW) incineration simulation, the traditional FLIC-Fluent coupling method suffers from long iteration cycles across multiple operating conditions and significant errors due to data mapping at the coupling interface. This study developed a fully coupled bed combustion simulation program based on Fluent User-Defined Functions (UDF). By integrating four modules—dynamic regulation of particle emissivity, zonal motion control of the grate, bed drag shielding, and wall collision-induced fragmentation—the program achieved fully coupled calculation of solid waste particle movement, bed combustion, and furnace flow fields within a single Fluent platform, completely replacing the bed calculation functions of FLIC software. A 750 t/d reverse-inclined forward-feeding grate furnace in a Chinese waste-to-energy plant was selected for engineering validation. The model was calibrated using continuous operational data from 12 on-site measurement points. Results showed that the computational time per operating condition was reduced by 71.4% compared to the traditional FLIC-Fluent coupling method. The relative error between simulated furnace temperatures and on-site measurements was ≤4.10%, significantly outperforming the 9.68% maximum relative error of the traditional method. The proposed method provides a reliable engineering simulation solution for optimizing operating conditions and screening blending schemes in co-incineration of multi-source solid waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508006
Landfill leachate, characterized by high ammonia nitrogen, high organic load, complex toxic components, and low nitrogen removal efficiency, poses significant environmental challenges. To achieve efficient nitrogen removal, a continuous-flow two-stage anoxic/oxic (A/O) moving-bed biofilm reactor (MBBR) system coupled with anaerobic ammonium oxidation (Anammox) was constructed and operated for long-term treatment of actual landfill leachate. After biofilm attachment and multi-gradient acclimation, influent concentrations were gradually increased from low levels (NH4+-N ~200 mg·L−1, COD ~2500–3000 mg·L−1) to high levels (NH4+-N ~1800 mg·L−1, COD ~8500 mg·L−1). During stable operation, average removal efficiencies of NH4+-N and COD reached 97.7% and 66.8%, respectively, with total nitrogen (TN) removal efficiency improving to 93.9%. Along the reactor, the first A/O stage achieved major organic degradation and ammonia oxidation, while the second stage facilitated nitrite accumulation and promoted Anammox for synergistic nitrogen removal. High-throughput sequencing revealed Proteobacteria as the dominant phylum (>50%), with denitrifying genera such as Azoarcus and Thauera significantly enriched. Planctomycetota abundance increased from 0.6% to 3.7%, and Candidatus Kuenenia was detected, confirming successful Anammox colonization and participation in nitrogen removal. This study validates the efficient combined nitrogen removal mechanism of the A/O–MBBR system with Anammox, providing theoretical basis and technical support for engineering treatment of high-ammonia wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509120
The 'Zero-Waste City' initiative, centered on source reduction, resource utilization, and safe disposal of solid waste, aims to minimize environmental impact. To quantitatively assess its carbon reduction contribution, this study took Mianyang as a case, systematically collecting data on solid waste generation, utilization, and disposal across industrial, agricultural, and other sectors from 2021 to 2024. Employing an improved WARM model and emission factor method, and incorporating generation, utilization, and disposal intensities, the carbon reduction benefits before (2021–2022) and after (2023–2024) the initiative were evaluated. Results show that despite significant improvements in comprehensive utilization and safe disposal rates, total solid waste generation increased, leading to a net negative carbon effect of -127.6×10^4 tCO2eq based on absolute quantities. However, after stripping economic and population growth factors, intensity-based accounting revealed a cumulative reduction of 10.8×10^4 tCO2eq, demonstrating significant synergistic benefits. The industrial sector contributed the most, with a reduction of 40.2×10^4 tCO2eq, driven by green transformation and enhanced utilization capacity. Conversely, the rising intensity of domestic solid waste generation resulted in a negative benefit of -46.1×10^4 tCO2eq, highlighting a key area for future improvement. The study underscores the necessity of considering both intensity and absolute quantity dimensions in evaluating rapidly developing cities. These findings provide practical evidence and reference pathways for advancing 'Zero-Waste City' construction and synergistic pollution reduction and carbon mitigation under the 'dual carbon' goals.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051502
Contamination of indoor air with illicit drugs poses a serious threat to public health and safety. Accurate and precise methods for monitoring these drugs are crucial for combating drug production, trafficking, and abuse, as well as reducing the risk of occupational exposure in law enforcement and healthcare workers. Current on-site rapid detection techniques for drugs in indoor air primarily include ion mobility spectrometry and electronic nose technology. Chromatography-mass spectrometry techniques are often used in the laboratory. Monitored drug types include heroin, amphetamine-type stimulants, cannabis, cocaine, synthetic cannabinoids, and fentanyl analogs, with concentration ranges ranging from a few ng·m−3 to several hundred µg·m−3. Drug concentrations are influenced by factors such as the drug type, methods involved in production and abuse, intensities of human activity, and ventilation conditions. While it has been demonstrated that long-term exposure to drug-contaminated environments may cause persistent physical discomfort, the specific mechanisms underlying health risks require further investigation. This paper reviews the sources of illicit drugs in indoor air, their detection methods, and typical application scenarios. It also analyzes the shortcomings of existing studies and proposes future research directions. The aim is to provide technical references for the monitoring of drugs in indoor air environments.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608023
Zinc-containing steel dust sludge, a by-product of steelmaking, contains high levels of chlorine (Cl) along with valuable metals such as Fe, Zn, K, and Na. When recycled into the steel production process, Cl accumulates, causing sintering instability and severe corrosion of blast furnace linings. This study investigated water leaching for Cl removal from zinc-containing steel dust sludge. Under optimal conditions (liquid-to-solid ratio 5 mL/g, temperature 70 °C, time 60 min, rotation speed 160 r/min), the Cl leaching rate reached 87%. Furthermore, a three-stage countercurrent water washing process at a liquid-to-solid ratio of 6 mL/g and room temperature for 45 min achieved a Cl leaching rate exceeding 90%. The water washing also reduced the leaching toxicity of metals in the sludge to a certain extent. Characterization via XRD, SEM, FT-IR, and XPS revealed that water washing primarily dissolved soluble chlorides (NaCl, KCl, etc.), increasing the specific surface area from 2.71 to 10.11 m²/g and average pore size from 12.83 to 16.29 nm. These findings provide theoretical and technical support for efficient Cl removal from zinc-containing steel dust sludge, facilitating its safe resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4097-3
The on-demand patterning of two-dimensional transition metal dichalcogenides (TMDs) with tailored edges is critical for electronic and optoelectronic applications but remains technically challenging. Here, we report a stress-guided anisotropic etching strategy for producing large-area, well-ordered MoS2 nanostructures, including nano-ribbons and nano-squares, without templates. By applying uniaxial cumulative stress followed by selective thermal etching, MoS2 monolayers are statistically etched into ribbon-like structures whose width inversely correlates with applied stress magnitude. The newly etched edges are macroscopically straight or serrated, predominantly Mo-zigzag terminated, and enhance photoluminescence by a factor of ~8.0. The edge type depends on the angle between stress direction and crystallographic orientation, corroborated by theoretical calculations. Biaxial stressing generates well-defined nano-squares, offering a scalable, versatile patterning route for engineering 2D materials with tailored functional edges, promising for electrocatalytic and optoelectronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4100-9
Shape memory droplet manipulation platforms have attracted significant attention due to their programmable droplet control capabilities. Current research primarily focuses on superhydrophobic surfaces and slippery lubricant-infused porous surfaces (SLIPS); however, these approaches suffer from vulnerable surface micro/nanostructures and loss of lubricant oils. Here, we report a shape memory quasi-liquid polydimethylsiloxane (PDMS) brush surface that overcomes these limitations. The surface is fabricated by introducing a SiO2 layer as a 'bridge' on a shape memory epoxy substrate, providing abundant functional groups for grafting PDMS brushes. By precisely controlling the SiO2 layer thickness and grafting conditions, the surface exhibits good shape memory properties and low adhesion to diverse liquids with varying surface tensions. Reversible anisotropic/isotropic droplet sliding control for both water and organic droplets is demonstrated through dynamic introduction/removal of groove structures, proving excellent droplet manipulation based on the combination of shape memory and low adhesion of PDMS brushes. Furthermore, the material can be applied as a functional coating on diverse substrates to impart anti-fouling and self-cleaning properties. This work introduces a nanoscale SiO2 layer as a 'bridge', offering a strategy to graft PDMS brushes onto polymer surfaces. Given the advantages of quasi-liquid PDMS brushes and programmable controllability of shape memory polymers, this work provides fresh ideas for developing droplet manipulation platforms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4164-3
Lithium metal anodes (LMAs) are pivotal for next-generation high-energy batteries, yet their commercialization is hindered by dendrite growth and unstable solid electrolyte interphase (SEI). Here, we report a dual-layered artificial SEI (ASEI) comprising an inner LiF-rich inorganic layer and an outer perfluoropolyether (PFOE) organic layer, fabricated via a scalable roll-pressing technique. The LiF-rich layer lowers Li-ion diffusion barriers and provides mechanical robustness, while the PFOE layer chemically stabilizes the interface against electrolyte oxidation. Symmetric cells with PFOE-LiF@Li anodes achieve over 1400 h of stable cycling at 30 mA cm−2 and 5 mAh cm−2. Full cells paired with LiFePO4 cathodes deliver 350 cycles at 1 C and over 550 cycles at 2 C with high capacity retention and Coulombic efficiency. This work establishes a design principle for interfacial engineering, combining inorganic rigidity with organic functionality, and offers a promising route for practical LMBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4181-6
Green hydrogen production via electrocatalytic water splitting is pivotal for sustainable energy, yet the high cost and scarcity of platinum (Pt) catalysts impede large-scale adoption. Ruthenium (Ru)-based materials emerge as promising alternatives, but their performance requires enhancement. Two-dimensional transition metal dichalcogenides (TMDs), particularly ReS2, offer intrinsic 1T' phase with good conductivity and stability, yet suffer from inert surfaces limiting water adsorption. Here, we report a heterostructure comprising Ru nanoclusters anchored on ReS2 nanosheets (Ru/ReS2) to modulate electronic structure via d-p coupling. This design enhances water dissociation kinetics and optimizes hydrogen adsorption free energy (ΔG_H*). The Ru/ReS2 catalyst exhibits superior hydrogen evolution reaction (HER) activity in acidic media, achieving an overpotential of 47 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, outperforming commercial Pt/C (overpotential 54 mV, Tafel slope 45 mV dec−1). Notably, it demonstrates exceptional stability, with negligible degradation after 10,000 cyclic voltammetry cycles, contrasting with Pt/C's 54 mV overpotential increase. Density functional theory calculations reveal that d-p coupling between Ru and ReS2 optimizes the electronic structure, facilitating water adsorption and dissociation. This work provides a rational strategy for designing efficient, durable, and cost-effective HER electrocatalysts for green hydrogen production.