SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3653-2
Designing photosensitizers with efficient intersystem crossing (ISC) and long-lived triplet excited states is critical for photodynamic therapy (PDT). However, conventional molecular design principles often rely on heavy-atom effects or specific donor-acceptor architectures, limiting generality. Here, we report a facile and rational strategy to convert intrinsically non-photosensitizing fluorophores into effective reactive oxygen species (ROS) generators by introducing guanidinium substituents. The modified photosensitizers exhibit prolonged triplet excited state lifetimes and considerable ROS production, in stark contrast to unmodified fluorophores which show intense fluorescence and negligible ROS generation. Electron paramagnetic resonance spectroscopy and high-resolution mass spectrometry confirm the formation of stable nitrogen-centered radical cations on the guanidinium moiety, stabilized by p-π conjugation. Mechanistic studies indicate that these radicals promote ISC and prolong triplet state lifetimes. In vitro and in vivo experiments demonstrate that guanidinium-modified photosensitizers induce immunogenic cell death (ICD) and elicit potent anti-tumor immunity. This work provides a universal and facile strategy for designing organic photosensitizers through stable radical cation-containing building blocks, expanding the scope of PDT agents.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3503-9
This correction addresses an image misuse in the original publication (Sci China Mater, 2025, 68(6): 2095, DOI: 10.1007/s40843-025-3311-6). Specifically, a fluorescent image in Fig. 4d, depicting live/dead cells after treatment with MPDA@TMZ without laser irradiation, was erroneously presented. The corrected Fig. 4 is provided, and the authors confirm that the results and conclusions of the original paper remain unaffected. The correction ensures the integrity of the reported data, particularly the cell viability and apoptosis assays. The study focuses on mesoporous bowl-shaped polydopamine (MPDA) nanoparticles co-loaded with temozolomide (TMZ) and indocyanine green (ICG) for synergistic glioblastoma therapy. The corrected figure includes CLSM images of G422 cells after incubation with various formulations (ICG, sPDA@ICG, mPDA@ICG, MPDA@ICG), cell viability curves, quantitative fluorescence intensity, live/dead staining, and apoptosis quantification. Statistical significance is denoted as ****p < 0.01. The correction maintains the scientific validity of the findings, which demonstrate the potential of MPDA-based nanoplatforms for combined chemo-photothermal therapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507057
This study presents a novel electrochemical sensor for the rapid detection of trace lead ions (Pb(II)) in water, utilizing a rod-shaped bismuth-based electrode. The electrode was fabricated by modifying a glassy carbon electrode (GCE) with basic bismuth nitrate [Bi6O5(OH)3](NO3)5·3H2O, synthesized via a chemical precipitation method. The sensor was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), electron probe microanalysis (EPMA), and energy-dispersive X-ray spectroscopy (EDS), confirming the rod-like morphology and composition. Electrochemical detection was performed using differential pulse voltammetry (DPV) in a 0.1 mol·L−1 NaAc-HAc buffer (pH 4.3). The sensor exhibited a linear detection range for Pb(II) from 1 to 90 μg·L−1, with a detection limit of 0.34 μg·L−1 and a sensitivity of 106 μA·(μmol·L−1)−1. The electrode demonstrated excellent anti-interference capability and reproducibility. Recovery tests in real water samples (tap water and campus lake water) yielded high recovery rates, indicating practical applicability. This work provides a simple, cost-effective, and reliable method for monitoring trace Pb(II) in environmental water, particularly relevant for public swimming pools and similar aquatic facilities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024092906
Microplastic pollution in rivers and lakes has become a research hotspot, yet studies in Anhui Province have predominantly focused on northern and central regions, leaving southern Anhui under-investigated. This study addresses that gap by examining the Xin'an River in Huangshan City, a typical river in southern Anhui. Surface water and sediment samples were collected in December 2023. In surface water, microplastic concentrations ranged from 350 to 3700 n·m−3, with particles of 0–0.5 mm dominating (33.93%). Fibrous shapes were most prevalent (59.83%), and colored particles accounted for 50.27%. In sediments, concentrations ranged from 25 to 200 n·kg−1, with 0–0.5 mm particles again dominant (49.63%). Fibers comprised 47.08% of sediment microplastics, and white particles accounted for 34.74%. Polymer analysis identified polyethylene terephthalate (PET) as the most abundant material (36.61%), followed by polyamide (PA) (23.22%). Source analysis suggests that fibrous microplastics originate primarily from fiber-based products such as clothing, home textiles, and fishing nets. These findings provide essential baseline data for water resource management, pollution assessment, and ecological remediation of the Xin'an River.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4094-8
Deep-blue multi-resonance thermally activated delayed fluorescence (MR-TADF) emitters with high efficiency, high color purity, and high brightness are critically important for next-generation OLED displays, yet remain challenging due to severe aggregation and host-guest interactions in the solid state. Herein, we report a core-encapsulating molecular design strategy in which bulky and non-conjugated peripheral groups are introduced to sterically encapsulate a blue-emitting MR core, thereby suppressing intermolecular π-π interactions without perturbing its intrinsic electronic structure. Two new emitters, DNa-BN and QNa-BN, featuring half-encapsulated and fully encapsulated MR-core architectures, respectively, were developed. Owing to its fully encapsulated structure, QNa-BN exhibits pronounced aggregation resistance at high doping concentrations, maintaining photoluminescence quantum yields exceeding 96%, radiative decay rate constants on the order of 10^8 s−1, and fast reverse intersystem crossing rates (~10^5 s−1). Consequently, sensitizer-free OLEDs based on QNa-BN deliver narrowband deep-blue emission at 458 nm with a full width at half maximum of 22 nm, CIE coordinates of (0.142, 0.085), a maximum external quantum efficiency (EQE_max) of 34.4%, and a maximum luminance exceeding 20,000 cd m−2. Furthermore, by adopting a hyperfluorescence architecture, the EQE_max is further boosted to 38.7% with significantly suppressed efficiency roll-off. This work demonstrates that steric encapsulation of the MR core provides an effective and general approach to achieving aggregation-resistant, high-efficiency, and high-brightness deep-blue MR-TADF emitters for OLED applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3595-7
Cu(I) complexes exhibiting thermally activated delayed fluorescence (TADF) have emerged as promising alternatives to noble-metal-based emitters for organic light-emitting diodes (OLEDs). However, the development of red-emitting Cu(I) complexes has been hindered by slow radiative decay and fast nonradiative decay. In this study, a linear two-coordinate Cu(I) complex, ICuTMC, was designed and synthesized. By pairing a pyrazine-fused N-heterocyclic carbene and a tetra-methylcarbazolyl ligand, a strong ligand-to-ligand charge transfer excited state is generated. Single-crystal structure authenticates close intramolecular C–H···Cu contacts, providing good steric shielding to the metal center. C–H···π interactions between ligands are also revealed. The complex exhibits highly efficient red TADF with emission maximum at 622 nm, photoluminescence quantum yield of 76%, and short delayed fluorescence lifetime of 0.24 μs. This is enabled by a large oscillator strength from the coplanar donor-Cu-acceptor conformation, a small singlet-triplet energy gap from spatial separation of frontier molecular orbitals, and strong spin-orbit coupling from the metal center. Vacuum-deposited OLEDs based on ICuTMC achieve a peak external quantum efficiency of 25.9% and a significantly small roll-off of 1.9% at 10,000 cd m−2. These performances demonstrate a way to overcome the energy gap law for linear coinage metal complexes toward red OLEDs.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61102-X
Silicon-carbon composites prepared by chemical vapor deposition (CVD) are promising anode materials for high-energy-density lithium-ion batteries. However, the influence of the pore structure of the porous carbon (PC) carrier on silicon deposition behavior, and the impact of surface silicon on cycling stability, remain unclear. This study systematically investigates these effects using nitrogen adsorption-desorption analysis, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Porous carbons with varying pore architectures were synthesized by adjusting KOH activator ratios. Results show that increased micropore volume facilitates higher silicon mass loading, but also elevates the content of surface floating silicon due to greater silane exposure. Moderately increasing mesopores in high-microporosity carbon promotes deeper silicon deposition, reducing surface floating silicon. Excessive surface floating silicon hinders lithium-ion diffusion kinetics, leading to accumulation of active lithium, accelerated SEI growth, and electrode degradation. Electrochemical testing reveals that the optimized silicon-carbon composite maintains a high specific capacity of 693.1 mAh/g after 150 cycles at 0.5 C (900 mA/g). This work provides new insights into the development and failure mechanisms of CVD-derived silicon-carbon composite anodes, emphasizing the critical role of pore structure in mitigating surface silicon and enhancing cycling stability.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605005
Water quality prediction is essential for river basin management, yet existing models often struggle with non-stationary, noisy monitoring data. This study collected water quality data from two city-level control sections in southern China from December 2020 to June 2024, including eight indicators: water temperature, turbidity, pH, conductivity, dissolved oxygen (DO), ammonia nitrogen (NH4+-N), total phosphorus (TP), and permanganate index (CODMn). To predict four key indicators (DO, NH4+-N, TP, CODMn), we developed hybrid models combining seasonal trend decomposition (STD), Bayesian hyperparameter optimization, and either random forest (RF) or XGBoost. STD smoothed and denoised the data while extracting seasonal factors; Bayesian optimization tuned model hyperparameters. Evaluation showed that the STD-Bayesian-XGBoost model achieved smaller bias errors and higher prediction accuracy than STD-Bayesian-RF. Specifically, XGBoost reduced root mean square error (RMSE) by 15-20% across all four indicators and improved the coefficient of determination (R²) to above 0.90, compared to RF's 0.85-0.88. The models were validated on southern river data, but the methodology is generalizable to other climatic and hydrological settings. This work provides a technical reference for pollution reduction and carbon management in regional watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605020
To address the high CO2 emission proportion in the industrial sector, distillers' grain waste was converted into biochar for CO2 adsorption from flue gas. Raw biochar suffers from weak pore adsorption and poor selectivity at elevated temperatures. This study employed ash self-templating and particle self-assembly to create hierarchical pores and simultaneously load amine groups onto distillers' grains-derived biochar, yielding amine-functionalized hierarchical porous carbon spheres. The amine loading significantly increased, providing more CO2 adsorption sites, while retaining macroporosity (total pore volume 0.0030–0.0066 cm3/g after amine loading), which enhanced morphological stability and CO2 mass transfer. The optimal sample, 0.2PW-K-CNF-PEI, exhibited a CO2 adsorption capacity of 1.03 mmol/g at 100 °C, a CO2 diffusion coefficient of 0.0495 min−1, and a selective adsorption capacity of 44 mg/g at 80 °C. This work offers a solution for valorizing distillers' grain by-products and capturing CO2 from low-temperature flue gas.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3993-y
Conventional liquid-phase in-situ synthesis of Cu-TiB2 composites often suffers from coarse and non-uniformly distributed reinforcements, stemming from insufficient understanding and control over the in-situ nucleation and growth mechanisms of TiB2 particles. This study introduces a novel melt dispersion-turbulent mixing (MDTM) in-situ reaction technology to fabricate high-performance Cu-TiB2 composites. The MDTM strategy synergistically refines reaction micro-regions by reducing the initial melt droplet size via melt dispersion while enhancing solute convection via turbulence, promoting high-density nucleation and refinement of TiB2 particles. Based on turbulence characteristics and in-situ reaction kinetics, we optimized the melt disperser parameters and established a quantitative model linking particle size to disperser rotation speed and reactant solute concentration. It was found that disperser rotation speed governs three distinct nucleation and growth mechanisms for TiB2 particles. Low-density nucleation at low disperser rotation speeds (0–50 r/min) leads to coarse TiB2 particles. At medium rotation speeds (100–150 r/min), the refinement of micro-regions in the dual-melt reaction achieves high-density TiB2 nucleation. Conversely, at high rotation speeds (150–200 r/min), intense turbulence weakens the nucleation driving force and induces TiB2 particle coarsening. This work provides new insights into liquid-phase in-situ reaction mechanisms and offers a novel, controllable route for fabricating high-performance micro/nano particle-reinforced metal matrix composites.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509051
Recyclables constitute a significant fraction of municipal solid waste (MSW) and hold substantial potential for resource utilization and greenhouse gas (GHG) emission reduction, contributing to carbon peak and carbon neutrality goals. However, reported GHG emission factors (EFs) for various recyclables vary widely across databases and literature, ranging from -19,110 to -125 kgCO2-eq·t⁻¹, with significant differences both among categories and within the same category, complicating accurate accounting. This study systematically integrates literature data on EFs for different recyclable categories, focusing on identifying factors causing intra-category variability. Data were collected from global databases (ecoinvent, WARM, CPCD, NAEI) and peer-reviewed studies over the past two decades, normalized to a functional unit of 1 tonne of recyclable. Statistical analysis (mean ± standard deviation) provided reference ranges for each category. Results show paper recyclables EFs range from -3,140 to 270 kgCO2-eq·t⁻¹, with corrugated cardboard and writing paper exhibiting higher absolute values than packaging paper due to structural strength and resource value. Plastic recyclables EFs range from -3,096 to -566 kgCO2-eq·t⁻¹, with EPS showing the highest reduction potential, followed by PET and PVC, then HDPE, LDPE, PP, and other plastics. Key influencing factors include functional unit definition, accounting scenario, system boundary, electricity emission factor selection, and calculation assumptions. The study recommends selecting EFs matching the specific accounting scenario and performing error analysis. Data gaps remain for LDPE, EPS, and other plastics, necessitating further experimental or field data. To enhance accuracy, calibration methods such as process-level and life-cycle inventory data calibration are proposed. This work provides a scientific basis for EF selection and calibration in GHG accounting of recyclables.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509001
To address low nitrogen removal efficiency in wastewater treatment plant (WWTP) effluent due to insufficient carbon sources and weak reoxygenation in conventional constructed wetlands (CWs), a tidal flow-subsurface flow integrated CW using iron-loaded biochar (BC-TF) as substrate was developed, with zeolite-based CW as control. Simulated wastewater experiments, water quality monitoring, nitrification/denitrification intensity assays, and high-throughput sequencing were employed. Results showed that tidal flow operation significantly enhanced removal of total nitrogen (TN) and ammonia nitrogen (NH4+-N), and increased nitrification intensity. Addition of iron-loaded biochar significantly improved TN and nitrate nitrogen (NO3−-N) removal, with BC-TF achieving an average TN removal of 86.03%, significantly higher than other groups (P<0.001). Microbial analysis revealed Proteobacteria, Actinobacteria, and Bacteroidetes as key phyla; iron-loaded biochar increased microbial abundance and diversity in tidal flow wetlands, while tidal flow alone reduced bacterial diversity. Pilot-scale experiments confirmed that tidal flow increased dissolved oxygen and nitrogen removal. This study is the first to combine iron-loaded biochar with tidal flow-subsurface flow CWs, systematically revealing the synergistic nitrogen removal mechanism of 'iron-loaded biochar-tidal flow-microorganisms', clarifying the role of iron-nitrogen coupling, and validating engineering applicability via pilot tests. The combination enhances reoxygenation, supplements carbon sources, and optimizes microbial community structure, effectively improving deep nitrogen purification of WWTP effluent, providing technical reference for tailwater treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025120801
The interaction between microplastic-derived dissolved organic matter (PSDOM) and iron oxides in soil environments can modulate its photosensitization effects, yet the underlying mechanisms remain elusive. This study investigated the influence of hematite with distinct morphologies—flake-shaped (HNPs) and cubic (HNCs)—on the photosensitization of polystyrene-derived dissolved organic matter (PSDOM). Under 500 W mercury lamp irradiation, both hematite morphologies promoted PSDOM degradation, with HNCs exhibiting superior performance: total organic carbon (TOC) decreased from 18.4 mg·L−1 to 12.3 mg·L−1 within 90 min, compared to 13.3 mg·L−1 for HNPs. Three-dimensional fluorescence spectroscopy indicated that hematite alters the humification process, thereby modifying photosensitization. Electron paramagnetic resonance (EPR) spectroscopy identified the generation of singlet oxygen (1O2), hydroxyl radicals (·OH), and carbon-centered radicals (CH3C(=O)OO·). HNCs significantly enhanced 1O2 production, while HNPs favored ·OH generation; both inhibited CH3C(=O)OO· formation. Quantitative analysis via high-performance liquid chromatography revealed that the steady-state concentration of 1O2 was highest with HNCs, reaching 2.80 times that of the PSDOM control, whereas ·OH concentration peaked with HNPs at 1.98 times the control. Notably, the steady-state concentration of 1O2 was approximately three orders of magnitude higher than that of ·OH. These findings elucidate the morphology-dependent role of hematite in PSDOM photosensitization, providing mechanistic insights into the environmental fate of microplastic-derived organic matter in complex soil systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030602
In the context of accelerated urbanization, regional air composite pollution in medium and large urban agglomerations is primarily characterized by PM2.5-O3 compound pollution. To elucidate the meteorological causes of PM2.5-O3 compound pollution in the Yangtze River Delta (YRD) region over the recent seven years (2017–2023), this study analyzed monitoring data from typical cities (Nanjing, Shanghai, Hangzhou, and Hefei) using Pearson and partial correlation coefficients. Results indicate: (1) PM2.5 pollution exhibited a significant downward trend across all four cities, with notable improvement during the COVID-19 pandemic in 2020, underscoring the effectiveness of air pollution control measures. Conversely, O3 pollution remained elevated or increased in some cities, indicating persistent challenges in O3 control. (2) During O3 pollution episodes, PM2.5 and O3 concentrations were positively correlated, whereas during PM2.5 pollution episodes, they were negatively correlated. (3) Compound pollution days were predominantly observed from February to October, with the highest frequency (20 days) occurring from April to June. (4) The significant reduction in PM2.5 weakened the aerosol 'umbrella effect', enhancing surface radiation and promoting near-surface O3 formation. Concurrently, changes in the NOx/VOCs ratio weakened O3 titration, and climate warming accelerated O3 precursor generation and potentially altered boundary layer structure, collectively contributing to O3 accumulation in the cold season and an increasing frequency of compound pollution during that period. (5) The formation mechanisms of PM2.5 and O3 are driven by distinct meteorological conditions, with low overall concentration correlation; however, under compound meteorological conditions such as high temperature, stagnant air, and weak diffusion, both pollutants tend to rise synchronously, indicating that compound pollution events are typically driven by multiple adverse meteorological factors. This study demonstrates that from 2017 to 2023, PM2.5 pollution significantly decreased while O3 pollution showed an increasing trend. Compound pollution was concentrated in April–June and influenced by high temperature, stagnant air, and weak diffusion. With effective PM2.5 control, enhanced surface radiation and changes in O3 precursors led to O3 accumulation in the cold season, increasing compound pollution frequency. Overall, compound pollution is driven by multiple meteorological factors, posing complex challenges for control.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021901
To assess the impact of the Air Pollution Prevention and Control Action Plan (APPCAP) on the chemical composition of PM2.5, this study analyzed the concentrations, existing forms, and sources of water-soluble ions in PM2.5 collected during summer (June–August) in the northern suburbs of Nanjing for the years 2012, 2013, 2017, and 2019. The results demonstrate a significant reduction in total water-soluble ion concentrations in 2017–2019 compared to 2012, indicating the effectiveness of APPCAP in mitigating PM2.5 pollution. Sulfate (SO4^2−), nitrate (NO3^−), and ammonium (NH4^+) (collectively SNA) were the dominant ionic species, contributing 69.98%–92.58% of the total ion mass, with SO4^2− being the most abundant. In the summers of 2013 and 2017, PM2.5 exhibited alkaline properties, and SNA primarily existed as NH4NO3 and (NH4)2SO4. Conversely, in 2019, PM2.5 became acidic, with SNA present as NH4NO3 and NH4HSO4. The nitrogen oxidation ratio (NOR) and sulfur oxidation ratio (SOR) indicated that NO3^− and SO4^2− predominantly originated from secondary reactions, with SO2 undergoing secondary conversion more readily than NO2, and the degree of secondary conversion increasing annually. Source apportionment revealed a shift from long-range transport in 2013 to local and regional sources by 2017. These findings underscore the success of APPCAP in reducing primary emissions and altering the chemical speciation of secondary inorganic aerosols, while highlighting the persistent dominance of sulfate and the need for continued SO2 emission controls.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606004
To identify optimal watershed remediation pathways under environmental and economic dimensions, an integrated environmental-economic impact assessment framework combining life cycle assessment (LCA) and life cycle costing (LCC) based on openLCA was established, using 1 m³ of treated wastewater as the functional unit. This framework comprehensively evaluated the environmental impacts and economic costs of three ecological buffer measures—constructed wetlands, ecological intercepting ditches, and vegetation restoration projects—in non-point source pollution control. The results indicated that constructed wetlands offer the optimal environmental-economic profile, featuring the lowest comprehensive cost (¥1.01 yuan/m³) and the lowest load across most environmental impact categories, with only slightly higher land resource consumption intensity. Ecological intercepting ditches exhibited higher impacts in areas such as metal resource consumption due to the use of rebars and base fertilizer inputs, resulting in a moderate comprehensive cost (¥1.57 yuan/m³). Vegetation restoration projects incurred the highest comprehensive cost (¥61.14 yuan/m³) and produced the most significant environmental impacts, with elevated indicators such as human carcinogenic toxicity. This primarily stemmed from the extensive use of concrete grass pavers and base fertilizer in rural river sections. These findings provide quantitative references for environmental-economic integrated evaluation and decision-making regarding ecological buffer zone engineering schemes in similar watersheds.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3820-5
Two novel N-heterocyclic carbene (NHC)-based ligands featuring rigid boron-oxygen (BO) fused-ring units, named Bpmi and Bpmb, and the two corresponding homoleptic meridianal iridium complexes, namely mer-Ir(Bpmi)3 and mer-Ir(Bpmb)3, were designed and synthesized. Single-crystal structures revealed a meridional coordination geometry for both complexes. Shorter Ir–C carbene bond lengths and rigid planar BO-fused ring units contribute to enhanced stability. Both complexes exhibit efficient green phosphorescence (λem = 536/521 nm in toluene, ΦPL > 78%) with short lifetimes (τ = 846/1083 ns), leading to high radiative rate constants (Kr = 10.04 × 10^5 and 7.29 × 10^5 s−1, respectively). Theoretical calculations indicate significantly increased metal-to-ligand charge transfer (MLCT) character (21.69% for mer-Ir(Bpmi)3; 17.30% for mer-Ir(Bpmb)3) compared to reference complexes (13.01% for mer-Ir(pmi)3; 15.99% for mer-Ir(pmb)3). Both complexes exhibit exceptional thermal stability with decomposition temperatures of 491°C (mer-Ir(Bpmi)3) and 540°C (mer-Ir(Bpmb)3). OLED devices using mer-Ir(Bpmb)3 and mer-Ir(Bpmi)3 as emitters demonstrate maximum external quantum efficiencies of 20.0% and 15.6%, respectively. This research pioneers boron-fused ring-containing NHCs and their phosphorescent iridium(III) complexes, establishing a novel design strategy for high-performance NHC-based OLED phosphorescent emitters.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026020207
Although the production and use of hexabromocyclododecanes (HBCDs) have been completely banned in China since December 2021, historical production activities may still leave high-concentration residual contamination in localized areas. This study investigated a typical legacy site of historical HBCDs production in eastern China. Surface and core soil samples were systematically collected both inside and outside the former plant area to characterize the occurrence, spatial distribution, and environmental burden of HBCDs, and to evaluate associated human health risks. Results showed that HBCD concentrations in soils outside the plant area ranged from below detection limit to 6.90×10² ng·g⁻¹ dw, while those inside the plant area were substantially higher, reaching up to 1.18×10⁶ ng·g⁻¹ dw. γ-HBCD was the dominant isomer; however, its relative abundance was lower than that reported in commercial HBCD mixtures and in previous studies conducted near production facilities. Outside the plant, HBCDs concentrations in soil generally decreased with increasing distance from the site, yet remained detectable at a distance of approximately 10 km (15.2 ng·g⁻¹ dw). Within the plant area, HBCDs concentrations in soil cores decreased with depth, declining from 1.08×10⁴–1.18×10⁶ ng·g⁻¹ dw in surface soils to 1.05–93.5 ng·g⁻¹ dw at depths of about 4 m. Analysis of the relative cumulative environmental burden indicated that although HBCDs loads were highest in the near-source area, they gradually accumulated over a broader spatial scale. Approximately 23.7%, 40.1%, 60.0%, and 87.1% of the total estimated burden accumulated within 2 km, 2.81 km, 4 km, and 6 km from the site, respectively. Health risk assessment indicated that oral ingestion of soil was the primary exposure pathway for different populations. Localized high-contamination zones within the plant area contributed significantly to non-carcinogenic risks, while overall risks for children outside the plant area were at acceptable levels.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607009
Resource utilization of food waste is a key measure for implementing waste classification and constructing zero-waste cities in China. However, the technical route based on anaerobic digestion currently faces developmental bottlenecks. In this study, engineering-scale facilities located in Northeast, North, Northwest, and Southeast China were selected, and material flow analysis was employed to comprehensively assess the current status of anaerobic digestion of food waste. The results indicated that, during the pretreatment stage, both leachate and organic slurry from all surveyed regions exhibited high COD/TN ratios, and the leachate contained high concentrations of lipids. Following three-phase (oil-water-solid) separation, the oil recovery rate could reach over 98%. Anaerobic digestion of each ton of food waste from the four regions generated approximately 70 to 80 Nm³ of biogas, while simultaneously producing liquid digestate accounting for 69% to 80% of the total mass and solid digestate accounting for 2.7% to 3.6%. However, the annual continuous production of digestate was not aligned with the seasonal demand for land use, thereby restricting the pathway for resource utilization. Converting food waste into an external carbon source can significantly enhance its resource utilization efficiency, with the economic benefits increasing by more than 203% compared to the methanogenesis pathway. The selection of the carbon source production technology route should be comprehensively determined by taking into account factors such as the specific nitrogen removal requirements of the target wastewater treatment process, the quality requirements for the carbon source products, and the substitution rate of commercial carbon sources.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607019
This study investigated the effects of biochar on volatile fatty acids (VFAs) production, biogas composition, physicochemical properties of the fermentation broth, and microbial community structure through batch anaerobic fermentation experiments using food waste as the substrate. The results demonstrated that the addition of biochar (1 g/L) significantly enhanced VFAs production, with the total VFAs concentration reaching 2150 mg/L in the biochar group, which was 30.2% higher than that of the control group (1651 mg/L). Acetic acid, propionic acid, and butyric acid were identified as the primary VFAs components. In the fermentation system, biochar exhibited a notable pH-buffering effect, stabilizing the fermentation environment. Additionally, its porous structure adsorbed ions during the fermentation process, resulting in a slightly lower electrical conductivity compared to the control group. Microbial community analysis revealed that biochar addition enriched key acidogenic bacteria, such as Defluviitoga and norank_f__Family_XI, optimizing the microbial community structure, and thereby facilitating organic acid production. In summary, biochar effectively promoted the efficient accumulation of VFAs during anaerobic fermentation of food waste by improving the fermentation microenvironment, enhancing system buffering capacity, and regulating microbial community composition. These findings provide theoretical support for sustainable enhancement of resource utilization of food waste.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3922-2
Photocatalytic reduction of CO2 to syngas (CO and H2) is pivotal for Fischer-Tropsch synthesis and carbon neutrality, yet suffers from rapid charge carrier recombination. Here, we report a solvent-induced defect engineering strategy to fabricate nitrogen vacancy (Nv)-modified Fe3O4 (Fe3O4-Nv-12h). Under visible light (λ ≥ 420 nm), Fe3O4-Nv-12h achieves a total syngas production rate of 43.55 mmol g−1 h−1 with a near 1:1 CO/H2 ratio, representing an 805.2-fold enhancement over pristine Fe3O4 and surpassing state-of-the-art systems. Electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS) confirm that Nv introduction modulates the electronic structure, acting as electron traps to suppress recombination and enhance charge transport. In situ Fourier transform infrared (FTIR) spectroscopy identifies *COOH and *CO as key intermediates for CO formation. This work establishes an effective nitrogen vacancy modification strategy for efficient photocatalytic CO2 conversion to syngas, offering new avenues for high-performance catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3964-5
The escalating demand for personalized thermal-moisture comfort, coupled with the high energy consumption of conventional heating and cooling systems and the imperative for low-carbon energy conservation, has driven the development of shape memory smart fabrics that respond to environmental changes. However, existing shape memory thermal-moisture management fabrics suffer from excessively high response temperatures, inadequate response performance, and suboptimal thermal-moisture management. In this work, a dual-network shape memory polymer (SMP) was synthesized, and its shape memory transition temperature was tuned to align with the human thermal comfort range. The polymer was processed into fibers and subsequently into twisted-coiled artificial muscles to enhance reversible strain. Woven with wool into a plain fabric, the resulting textile exhibits adaptive thermal-moisture management, achieving a warp reversible strain of up to 17.5%. At elevated temperatures, the fabric contracts, exhibiting an air permeability of 1546 mm/s and thermal conductivity of 0.0518 W/(m·K); at lower temperatures, it elongates, with air permeability of 1322 mm/s and thermal conductivity of 0.0426 W/(m·K), thereby realizing 'warm when cool and cool when hot' functionality. Compared with commercial wool fabrics, this smart fabric lowers the skin microenvironment temperature by 1.5 °C and offers an energy savings potential of approximately 222.58 MJ/m² per year in capital cities such as Beijing. This work provides a novel technical pathway and design approach for future personalized comfort and low-carbon, energy-saving textiles.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608013
Eutrophication and cyanobacterial blooms threaten aquatic ecosystems and drinking water safety globally. This study evaluated the efficacy of a compound algicide (PQGA-126, PAC, and red soil) combined with submerged plants (Vallisneria natans and Hydrilla verticillata) for suppressing blooms and restoring eutrophic water. Indoor static experiments used algae-laden water from Nanhu Lake, Gongqingcheng, Jiangxi. Six treatments were established: control, V. natans alone, H. verticillata alone, algicide alone, algicide + V. natans, and algicide + H. verticillata. Results demonstrated that combined treatments significantly reduced total nitrogen (TN), total phosphorus (TP), chlorophyll-a (Chl-a), and turbidity, markedly lowering eutrophication within a short period. The combined approach outperformed single-plant treatments, with algicide + V. natans achieving the greatest reduction in the comprehensive trophic state index. Additionally, the algicide significantly enhanced V. natans growth rate and H. verticillata catalase (CAT) activity, indicating species-specific physiological responses. These findings suggest that integrating compound algicide with submerged plants, particularly V. natans, offers a promising strategy for rapid and effective eutrophic water remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4021-5
Lead-free halide double perovskites have attracted significant attention owing to their eco-friendliness, structural tunability, and self-trapped exciton emission. Nevertheless, achieving efficient and stable near-infrared-II (NIR-II) luminescence, especially in materials incorporating lanthanide ions, remains a considerable challenge in photonics research. Herein, we report a notable advance in the design and synthesis of Sb3+-sensitized Cs2NaLuCl6:Er3+ double perovskite single crystals, which exhibit an unprecedented external quantum efficiency of 45.3% for emission at 1542 nm. Sb3+ acts as a broadband ultraviolet absorber and transfers energy to Er3+ via self-trapped exciton emission. Moreover, at high concentrations of Er3+, Er3+-Er3+ cross relaxation (2H11/2 + 4I15/2 → 4I9/2 + 4I13/2) selectively populates the NIR-emitting 4I13/2 state, suppressing competitive visible emission pathways. This synergistic host-sensitizer-activator design strategy, supported by density functional theory calculations, addresses long-standing efficiency limitations and opens new avenues for high-performance NIR-II emitters in bioimaging, night vision, and optical communications.