SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4306-5
Olefin-paraffin separation is a critical and energy-intensive process in the petrochemical industry, with ethylene and propylene purification alone consuming 0.3% of global energy. Current distillation methods are energy-inefficient, and polymer membranes exhibit inadequate separation performance. Metal-organic frameworks (MOFs), particularly ZIF-8, offer precise molecular sieving due to their uniform pore aperture (~3.4 Å), which lies between the kinetic diameters of propylene and propane. Despite excellent lab-scale performance, ZIF-8 membranes face scalability challenges, with effective areas typically below 10 cm², far from the tens of thousands to millions of square meters required industrially. This paper reviews a recent breakthrough by Weihong Xing, Yichang Pan, and colleagues, who developed a micro-space transformation process (MSTP) for scalable fabrication of heterostructured ZIF-8 (HZIF-8) membranes. Using sealed inner lumens of tubular ceramic supports as confined reaction spaces, they achieved single-tube areas of ~200 cm² and total fabricated areas exceeding 4.6 m². The membranes demonstrated stable separation performance over 30 days at 17 bar and 55 °C with a feed flow of 20 Nm³ d⁻¹. This work represents a significant step toward industrial application, addressing critical bottlenecks in membrane area expansion, defect control, and mechanical stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604017
The Shule River Basin, a typical arid inland river basin, faces critical water scarcity that threatens ecological security and sustainable development. This study integrated the FLUS and InVEST models to simulate water yield in 2030 and 2050 under three climate scenarios (SSP119, SSP245, SSP585). Geographic detectors quantified the driving mechanisms of natural and human factors. Results showed: (1) Desert dominates land use (78.6% in 2020). Under SSP119, desert area decreases by 0.69% by 2050, while under SSP585 it expands by 5.7%, with grassland loss of 23.0%, indicating severe ecological degradation. (2) Water yield exhibits a south-high, north-low spatial pattern, with high values in glacier-covered and high-altitude areas. SSP119 yields the most significant increase (147.6×10^8 t by 2050), whereas SSP585 shows minimal increase (43.9×10^8 t) due to extreme climate. (3) Precipitation and DEM are core driving factors; the interaction between land use type and precipitation has the strongest influence, implying that artificial land use changes can significantly regulate water yield. This multi-scenario framework provides decision support for water resource management and ecological governance in arid inland river basins.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026030202
High nitrogen (N) inputs, low N use efficiency, and substantial greenhouse gas emissions constrain sustainable double-cropping rice production in the middle and lower reaches of the Yangtze River. To evaluate whether humic acid urea (HAU) can reconcile yield stability with N reduction and carbon mitigation, a field experiment was conducted in a double-cropping rice system. Five treatments were established: conventional urea at the recommended N rate (U), HAU at the recommended N rate (HAU), conventional urea with a 20% reduction in N input (U-20), HAU with a 20% reduction in N input (HAU-20), and a no-N control (CK). Rice yield, N uptake and utilization, and the full life-cycle carbon footprint were quantified. Results showed that HAU significantly increased double-cropping rice yield by 6.46% (early rice) and 8.76% (late rice) compared to U (P < 0.05). HAU-20 maintained yield equivalent to U, while U-20 significantly reduced yield. HAU-20 significantly improved nitrogen fertilizer apparent utilization rate, agronomic efficiency, and partial factor productivity. Specifically, apparent utilization rate increased by 9.24 percentage points (early rice) and 7.80 percentage points (late rice); agronomic efficiency increased by 18.51% and 26.69%, and partial factor productivity by 22.79% and 25.58% for early and late rice, respectively (P < 0.05). Life-cycle carbon footprint was significantly reduced by 26.25% (early rice) and 40.38% (late rice) under HAU-20 compared to U, with per-unit product carbon footprint reduced by 0.22 t CO2-eq·t−1 and 0.86 t CO2-eq·t−1, respectively. The reduction was primarily attributed to decreased CH4 and N2O emissions: early rice CH4 and N2O cumulative emissions decreased by 28.92% and 44.34%, and late rice by 44.46% and 63.85% (P < 0.05). In conclusion, HAU with 20% N reduction sustains yield, enhances N use efficiency, and significantly lowers carbon footprint, offering a viable path for green and low-carbon double-cropping rice production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3979-3
The escalating prevalence of multidrug-resistant Pseudomonas aeruginosa (P. aeruginosa) infections necessitates novel antibacterial strategies. Here, we engineered lectin B (LecB)-targeted glyco-dots (TFP2F) via self-assembly of a photosensitizer (TFP2) possessing aggregation-induced reactive oxygen species (ROS) generation capability with fucose-modified tetraphenylethene glycoclusters (TPE-Fuc4), enabling P. aeruginosa-targeted antimicrobial photodynamic therapy and wound healing promotion. Three photosensitizers (TFP0–2) featuring an “A-D-A” electronic structure were synthesized, exhibiting broad absorption bands and near-infrared (NIR) fluorescence. Among these, TFP2 demonstrated superior Type-I/II ROS production (including ·OH, ·O2−, and 1O2), achieving potent phototoxicity against P. aeruginosa (MIC80 = 7.5 μM). Self-assembly with TPE-Fuc4 yielded glyco-dots TFP2F that facilitated LecB-mediated bacterial targeting, enhanced bacterial uptake, and significantly reduced the MIC80 to 2.5 μM against drug-resistant P. aeruginosa under light irradiation. In a murine P. aeruginosa-infected wound model, TFP2F treatment combined with light irradiation accelerated wound closure to <20% of the initial area by day 8 (vs. >40% in controls) and eliminated >95% of bacteria by day 2. This work presents a convenient strategy for constructing glyco-dots as a potent functionalized platform for precision, lectin-targeted antimicrobial photodynamic therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4009-0
Micro light-emitting diode (Micro-LED) display technology is a promising next-generation display technology due to its high brightness, high contrast, low power consumption, long life, and fast response. However, aggressive downscaling of Micro-LEDs to a few microns makes lift-off fabrication of metal bumps for soldered joints between Micro-LEDs and driver substrates increasingly difficult, challenging high-yield bump arrays under high-density conditions. This study innovatively replaces conventional metal bumps with a photosensitive conductive polymer (PCP), enabling fabrication of polymeric micro-bump arrays via well-established photolithography, bypassing complex lift-off processes and reducing short-circuit risk. Isopropyl alcohol regulates developer wettability for optimal development, yielding bump arrays with bump size 20 μm × 12 μm and height (1.9288 ± 0.0213) μm on thin-film transistor (TFT) drivers with yield over 99.99%. The issue of low bonding yield from polydimethylsiloxane (PDMS) thermal expansion was resolved by adjusting chip spacing on the temporary substrate, achieving bonding yield exceeding 99.8%. A 0.99-inch full-color Micro-LED display with density 114 pixels per inch (PPI) and brightness 5537 cd/m² was fabricated. High-yield bump arrays, Micro-LED arrays, and high bonding yield are highly reproducible, promoting development of Micro-LED displays and related fields.