SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4200-0
Self-powered broadband photodetectors are pivotal for next-generation intelligent healthcare. Solution-processed mercury sulfide (HgS) is an attractive near-infrared absorber but is limited by interfacial instability, high defects, and sluggish response. Inspired by sulfur-mediated adhesion in Alhagi sparsifolia, a bioinspired interfacial engineering strategy employs an antimony sulfide (Sb2S3) interlayer to construct a bidirectional chemical bonding network. The Sb2S3 interlayer simultaneously forms Sb–O bonds with fluorine-doped tin oxide (FTO) substrates and Sb–S/Hg–S bonds with the HgS layer, thereby reinforcing interfacial adhesion, passivating coordination-unsaturated defect states, and establishing a type-II heterojunction with a strong built-in electric field. The resulting Sb2S3/HgS photodetector exhibits self-powered operation, broadband sensitivity spanning the visible to near-infrared region (642–1550 nm), an ultrafast response time of 2.47 ms, a detectivity up to 1.7 × 10^11 Jones, and retaining nearly constant photocurrent over 5000 continuous on-off switching cycles as well as prolonged air exposure. Beyond device-level performance, we demonstrate its utility in intelligent healthcare scenarios, including machine-learning-assisted liquid drug identification, binary-coded optical wireless communication, and high-fidelity photoplethysmography monitoring. This work establishes biomimetic bidirectional bonding as a generalizable paradigm for stabilizing solution-processed chalcogenide optoelectronics and accelerates the integration of self-powered broadband photodetectors into intelligent healthcare systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3682-6
Metal single-atoms with optimized coordination structure on highly accessible substrate can maximize the metal utilization efficiency along with enhancing catalytic activities. Herein, axial nitrogen-coordinated Fe-N5 sites on N-doped carbon (denoted as FeN5@N-C) hollow microplates are fabricated via a unique Fe3+-chelated polydopamine assisted hollowing strategy using ZIF-L microplates as multifunctional templates. Due to the powerful chelating and adhesive ability of polydopamine, this hollow-carbon strategy can be extended to fabricate single-atom Fe-N-C hollow structures with different shapes and encapsulate other transition-metal single atoms (Ni, Co, Mn, and Cu) into the N-doped carbon hollow microplates. The FeN5@N-C hollow microplates exhibit outstanding oxygen reduction reaction (ORR) capability with an impressive half-wave potential of 0.93 V vs. reversible hydrogen electrode and high stability, which can serve as air-cathode catalysts for high-performance Zn-air batteries with high peak power density of 225.3 mW cm−2 and stable cyclability of up to 400 h. Comprehensive analysis and theoretical calculations elucidate that axial nitrogen coordination in Fe-N5 catalytic sites, unlike the planar Fe-N4 configuration, can compete well with the bonding of OH* through additional 3d-2p orbital hybridization, thereby giving moderate bonding strength to enhance the ORR activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3603-2
Conventional glass fiber/epoxy (GF/EP) composites, while structurally competent, are hindered by poor interlaminar toughness, low thermal conductivity, and electromagnetic transparency. This study transforms GF/EP composites into advanced structural multifunctional materials by embedding Ti3C2Tx MXene/poly(acrylic acid) (PAA) aerogels (TPA) as integral interlayers. Hybrid composites with tailored architectures—aligned (GFAM_A) and random (GFAM_R) TPA/GF/EP laminates—were fabricated via unidirectional and isotropic freeze-casting, respectively. The integrated aerogel phase promotes crack deflection and distributed energy dissipation, leading to notable enhancements in interlaminar shear strength (ILSS) and fracture toughness. The continuous Ti3C2Tx MXene network within the aerogel creates efficient through-thickness thermal conduction pathways and imparts strong microwave absorption properties. Notably, GFAM_A achieves simultaneous increases of approximately 52% in ILSS, 78% in toughness, and 42% in thermal conductivity, along with effective microwave absorption: a minimum reflection loss of −23.47 dB and a maximum effective bandwidth of 2.70 GHz. This study demonstrates that precision aerogel engineering provides a powerful strategy for upgrading conventional glass fiber composites into advanced multifunctional structural materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3671-0
Photothermal therapy (PTT) is a non-invasive tumor treatment that offers controllability, non-drug resistance, and precise ablation, yet its efficacy is limited by uncontrolled heat diffusion and weak immune responses, often leading to metastasis. Here, we report a chondroitin sulfate-modified Prussian blue-montmorillonite immunoregulator (PM@CS) that integrates tumor cell adhesion and Golgi targeting to confine photothermal damage at the organelle level. PM@CS accumulates on the Golgi apparatus, reducing heat transfer distance and enhancing photothermal ablation. This targeted hyperthermia disrupts post-translational modification and secretion of metastasis-associated proteins, with GOLPH3 and GOLM1 expression reduced by 63.4% and 70.3%, respectively. Furthermore, PM@CS promotes dendritic cell maturation (3.3-fold increase in CD80+ and CD86+ populations) and enhances antigen-specific CD4+ and CD8+ T cell proliferation, attributed to the immunoadjuvant properties of montmorillonite. Notably, PM@CS upregulates voltage-gated calcium channels (CaV) and enhances Ca2+ influx, activating calcium signaling cascades that amplify immunotherapy. This synergistic approach inhibits primary tumor growth and lung metastasis, offering a promising strategy for cancer treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3707-8
Wound infection is a major cause of death during the wound healing process. Improperly dressed wounds can lead to secondary injury, prolonging healing time and increasing infection risk. Here, we propose an antibacterial slippery dressing through molecular engineering of copper ions. The oil layer forms a barrier to reduce clot adhesion to the wound site and prevent environmental contamination. Single-cell level detection indicates that secreted copper ions induce bacterial death not only by disrupting membrane integrity but also by relying on the production of reactive oxygen species. Further membrane depolarization and adenosine triphosphate production blockage result in the aggregation of important proteins in various biological processes, such as metabolic homeostasis, ultimately leading to bacterial death. The animal model confirms that our dressing accelerates wound healing by promoting the growth of granulation tissue and collagen deposition. Our dressing demonstrates significant clinical implications for the design of next-generation therapeutic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3747-3
Thermochromic soft materials are flexible functional materials that adaptively tune optical properties (transmittance, reflectance, or scattering) with temperature for thermal modulation. Herein, a laminated thermochromic gel (DEE-DA) is synthesized by encapsulating a thermochromic hydrogel (DA) between two hydrophobic ionogels (DEE) in a stacked configuration. The synergy of multiple dynamic bonds endows the DEE-DA gel with exceptional mechanical properties and remarkable self-healing capability (98.8% at 30 °C). More importantly, attributed to the temperature-responsive reversible cleavage and recombination of hydrogen bonds and borate ester bonds, DEE-DA gel demonstrates tunable transmittance with a light modulation efficiency of 85.45%. In response to the various external conditions, the gel can auto-adjust the optical properties to avoid sun irradiation or heat loss. Accordingly, the gel enables efficient dual-mode thermal modulation across a broad temperature range to realize thermal management. The research proposes gel thermochromism and laminated durability enhancement for adaptive materials in smart buildings and wearables.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122001
Biomass is the only renewable carbon resource with huge reserves and wide sources, and it is green and environmentally friendly. Under the background of 'dual carbon', the clean and efficient utilization of biomass has received increasing attention. Preparation of biochar from biomass is one of the main methods to use biomass efficiently. Biochar surfaces possess porous and aromatic structures, which exhibit good fixation effects on heavy metals in wastewater. However, biochar has shortcomings such as difficulty in recovery and non-reusability. The introduction of iron into biochar can not only enrich surface functional groups, develop pore structure, and increase specific surface area, but also endow magnetic properties, facilitating solid-liquid separation after adsorption. This paper reviews the preparation methods of iron-based magnetic biochar (MBC-Fe), summarizes the effects of different iron sources on its characteristics, and illustrates the adsorption performance and mechanisms of MBC-Fe for typical heavy metals in water. Finally, applications of MBC-Fe in the removal of heavy metal ions from wastewater are concluded, and future utilization potential in other fields is proposed. The review highlights that MBC-Fe exhibits high adsorption capacities, e.g., for Pb(II) and Cd(II), with rapid kinetics and easy separation, making it a promising adsorbent for wastewater treatment.
Environmental Chemistry•2026•DOI: 10.0000/202604-1
An analytical method was developed for the simultaneous determination of 11 organic ultraviolet absorbents (OUVs) in coral tissues using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Target analytes included benzophenones (BP, BP-2, BP-3, BP-8) and other common UV filters. Sample pretreatment and chromatographic conditions were systematically optimized. Coral tissue samples were extracted by combined vortexing and ultrasonication, separated on a CAPCELL PAK MG C18 column using a mobile phase of methanol-0.1% formic acid aqueous solution under gradient elution, and determined by multiple reaction monitoring (MRM) with internal standard quantification. Method validation demonstrated good linearity for all target compounds over the range of 0.1–500 μg·L−1 (R2 > 0.990), with method detection limits ranging from 0.020 to 0.133 ng·g−1. The mean recoveries at low, medium, and high spiking levels ranged from 60.5% to 120.3%, with relative standard deviations (RSDs) of 1.6%–10.7%. The method offers advantages of simple pretreatment, good repeatability, and high accuracy, making it suitable for high-throughput determination of OUVs in complex biological matrices such as corals. The method was applied to analyze 89 coral samples collected from Xidao Island, Sanya, and five target OUVs were detected in the samples. This method provides reliable technical support for elucidating the accumulation characteristics of OUVs in corals and assessing their potential ecological risks.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508036
To address the issues of insufficient carbon sources and low denitrification efficiency in rural domestic wastewater, this study developed and optimized a composite slow-release carbon source using corncob, rice husk, reed straw, polyvinyl alcohol (PVA), and sodium alginate (SA). The preparation conditions and raw material ratios were systematically optimized using Plackett-Burman (PB) design, response surface methodology (Box-Behnken design, BBD), and mixture-optimal design (MOD). The denitrification performance was evaluated through carbon release characteristics and denitrification experiments. The optimal preparation conditions were determined as PVA 8.64 g, SA 2.41 g, rice husk 3.82 g, corncob 4.47 g, reed straw 6.06 g, freezing time 19.11 h, and crosslinking time 12 h. The 7-day cumulative carbon release was (43.38 ± 1.3) mg·(g·h)−1. The release process followed first-order kinetics, Higuchi, Ritger-Peppas, and Weibull models, indicating that carbon release is controlled by multiple mechanisms including diffusion and skeleton erosion, ensuring stable slow-release characteristics. In denitrification experiments with influent NO3−-N concentration of 50 mg·L−1, the composite carbon source (RCR-PVA-SA) achieved a maximum NO3−-N removal rate of 90.8% after 10 days of operation, with a removal rate of 0.079 mg·(g·h)−1. Under dynamic conditions with hydraulic retention time (HRT) of 3 h, the average removal rate remained at 87.9%, demonstrating efficient and stable denitrification performance under both static and dynamic conditions. This research provides a reference for the preparation of natural slow-release carbon sources and the resource utilization of agricultural waste.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012302
Phosphorus (P) loss from paddy fields contributes to eutrophication in Chaohu Lake. This study evaluated the effects of novel fertilizers and P reduction on P loss and rice yield. Seven treatments were established: no P (CK), rice-specific fertilizer (ZYF), slow-release blended fertilizer (SRF), Xinjutian compound fertilizer (XJT), enhanced loss-controlled fertilizer (CRF), CRF with 10% P reduction (CRF-10P%), and CRF with 30% P reduction (CRF-30P%). Results showed that novel fertilizers and P reduction significantly reduced concentrations of total phosphorus (TP), dissolved phosphorus (DP), and particulate phosphorus (PP) in surface water and leachate. The first 5 days after basal fertilization and heavy rainfall were high-risk periods for P loss. Rainfall increased TP concentrations by 417.74%–432.86% and 94.85%–351.35% in surface water and leachate, respectively; DP increased by 120.80%–322.44%, and PP by 280.66%–501.77% and 80.23%–297.55%. Compared with ZYF, SRF, XJT, and CRF reduced TP loss by 15.43%–33.95%, with SRF showing the lowest loss. Under P reduction, CRF-10P% and CRF-30P% reduced TP loss by 31.48% and 37.04%, respectively, with CRF-30P% achieving the lowest loss. Notably, CRF-10P% increased rice yield by 22.37% relative to ZYF, indicating that moderate P reduction with enhanced loss-controlled fertilizer can maintain or increase yield while reducing environmental risk. The study concludes that CRF-10P% offers a promising strategy for sustainable rice production in the Chaohu Lake watershed.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225141
This study established a three-dimensional transient gas-liquid two-phase flow model based on a 150-tonne converter to investigate the influence of the number of clogged bottom-blowing elements on the stirring efficiency of the molten pool. The numerical simulation results were validated against actual converter operating conditions. The findings revealed that the primary reason for deteriorated flow characteristics under multiple clogged tuyeres was the overall reduction in stirring energy input from the bottom-blowing gas. Specifically, when the number of clogged tuyeres reached three, the numerically simulated mixing time increased from 150.6 s to 219.3 s, a significant increase of 45.62%. This numerical result was in good agreement with water model experiments, indicating that prompt furnace bottom maintenance and tuyere replacement should be considered under such circumstances. At the same bottom-blowing intensity, the effective stirring area of a single inner-ring tuyere was 0.919 m2, while that of a single outer-ring tuyere was 1.651 m2. The combined effective area achieved through the synergy of inner and outer ring tuyeres was 2.940 m2, which was 14.4% greater than the sum of their individual areas. Clogging disrupted this synergistic stirring effect. A single clogged tuyere had a negligible impact on the distribution of dead zones. However, when tuyeres in both the inner and outer rings were clogged, dead zones became more numerous and concentrated. With 3 and 4 clogged tuyeres, the dead zone volume reached 3.703 and 5.946 m3, accounting for 17.31% and 27.79% of the total molten pool volume, respectively. An industrial plant trial conducted based on the numerical simulation scheme showed that key performance indicators deteriorated as the number of clogged tuyeres increased. With three clogged tuyeres, the average end-point oxygen content reached 0.0669wt%, which was 22.1% higher than that under non-clogged conditions. Concurrently, the total iron content in the slag reached 19.44%, a 24.5% increase compared to the non-clogged baseline.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3812-5
Anaerobic bacterial infections, prevalent in oxygen-deprived tissues, are recalcitrant to conventional antibiotics due to slow bacterial metabolism and the generation of nutrient-rich niches that foster polymicrobial biofilms. Propionibacterium acnes (P. acnes), a skin commensal, exemplifies this challenge, causing acne vulgaris and implant-associated infections, with rising antibiotic resistance. This study introduces an antimicrobial peptide (AMP), WRK (sequence: WRKFRRFKFRW-NH2), which induces endogenous reactive oxygen species (ROS) production in anaerobic bacteria, exploiting their inherent low ROS tolerance. WRK exhibited potent antibacterial activity, with a minimum inhibitory concentration (MIC) of 4 μg mL−1 against planktonic P. acnes and a minimum biofilm eradication concentration (MBEC) of 64 μg mL−1. To enable dermal delivery, WRK was encapsulated in layered dissolving microneedles (MNs), which demonstrated adequate mechanical strength for skin penetration. In a mouse back acne model, AMP MNs significantly reduced P. acnes infection and inflammation, outperforming commercial clindamycin gel. Histological analysis confirmed reduced inflammatory cell infiltration and tissue hyperplasia in the AMP MN group. This strategy offers a promising approach for treating anaerobic infections without promoting drug resistance, addressing a critical unmet need in clinical dermatology and implant surgery.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021101
This study investigated the toxic effects of intrauterine benzo[a]pyrene (BaP) exposure on pancreatic development and glucose metabolism in first-generation offspring rats. Pregnant Wistar rats were randomly divided into control and treatment groups receiving 200, 800, or 1600 μg·kg−1 BaP via daily oral gavage during gestation until delivery. Pancreatic histology was assessed in offspring at postnatal day 2 and week 12. Protein and mRNA expression of pancreatic duodenal homeobox-1 (PDX-1) and mitochondrial transcription factor A (TFAM) were quantified. Intraperitoneal glucose tolerance tests (IPGTT) and insulin tolerance tests (IPITT) were performed at week 12. Results showed that exposure to 800 and 1600 μg·kg−1 BaP caused dose-dependent pancreatic damage, with more severe islet morphological disruption and reduced islet area, which did not improve with age. PDX-1 and TFAM expression levels decreased in a dose-dependent manner at both time points. At week 12, the 1600 μg·kg−1 group exhibited pre-diabetic symptoms, including elevated blood glucose and insulin levels, and impaired glucose tolerance and insulin sensitivity. These findings indicate that intrauterine BaP exposure leads to persistent pancreatic developmental impairment and glucose metabolism disorders, potentially mediated by downregulation of PDX-1 and TFAM, with no recovery over time.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3943-y
Biodegradable polymers are promising for bioelectronic materials, yet simultaneously improving their mechanical, electrical, and optical performance remains a major challenge. Poly(3-hydroxybutyrate-co-4-hydroxyvalerate) (P34HB), a microbially synthesized polyhydroxyalkanoate (PHA), exhibits excellent biocompatibility and degradability but suffers from poor chain length control, limiting its functional performance. Here, we report a low-temperature, non-destructive supercritical ethyl alcohol-assisted polymerization (SEAP) strategy to enhance P34HB at the molecular level. Operating at 40 °C and 1500 psi, SEAP combines the permeability of supercritical CO2 with ethanol-mediated catalysis to promote in situ dehydration polymerization and efficiently remove impurities. Post-treatment, P34HB exhibits a 16% increase in number-average molecular weight, along with a record-high Young's modulus of 51.08 GPa and a 144% increase in elongation at break, overcoming the conventional trade-off between stiffness and ductility. Optical performance is also improved, with transmittance rising by 44% and refractive index increasing to 1.2. Material analyses confirm a higher ester group density and reduction of residual impurities. Electrical insulation is notably enhanced, with leakage current reduced by 50% to below 1 pA and reduced dielectric loss to 0.06. Cytotoxicity assays further verify excellent biocompatibility. This work establishes SEAP as a sustainable strategy for functionalizing P34HB, enabling its deployment in next-generation bioelectronics and flexible electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3918-x
Electrochemical seawater electrolysis powered by renewable energy is a highly promising route toward sustainable hydrogen production, mitigating both energy shortages and carbon emissions. However, chloride-induced corrosion and competitive chlorine evolution reactions lead to metal site dissolution, severely impairing durability, especially at industrial-level current densities. Here, we report a nitrite-incorporated cobalt-iron layered double hydroxide (CoFe-NO2−-LDH) electrocatalyst that exhibits exceptional activity and stability for seawater splitting. The nitrite anion acts as an electronic pump: it accepts electrons to facilitate the formation of high-valence Fe species essential for initial OER activation, and donates electrons under high potential to suppress oxidative dissolution. Moreover, the negatively charged nitrite generates an electrostatic repulsion field that effectively repels chloride ions, protecting metal active sites from corrosion and segregation. The in situ characterization confirms that nitrite doping weakens the Fe–O covalency, which suppresses lattice oxygen participation and promotes a stable adsorbate-evolving mechanism, consequently leading to significantly enhanced operational stability. When used as an anode, the CoFe-NO2−-LDH catalyst achieves over 1000 h of stable operation at 1000 mA cm−2 in seawater electrolysis, demonstrating great potential for practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511055
To systematically investigate the spatiotemporal distribution of hydrodynamics and water quality under cascaded hydropower development in the upper Heihe River, a MIKE21-based water environment model was constructed for the mountainous reach. The model simulated the dynamic changes of total phosphorus (TP), total nitrogen (TN), and ammonia nitrogen (NH3-N) from January to August 2023. Calibration and validation against field data showed good performance: the hydrodynamic model achieved a coefficient of determination (R2) of 0.89 and a mean relative error (MRE) of 11.3%; the water quality model achieved an average R2 of 0.86 and an average MRE of 14.21%. Hydrodynamic simulations revealed average flow velocities of 1.78, 0.72, and 0.36 m·s−1 during wet, normal, and dry periods, respectively. Natural river sections exhibited high velocities up to 4.3 m·s−1, while reservoir sections had near-stagnant flow due to hydraulic structures. Water quality simulations indicated that TN and NH3-N concentrations were higher in dry and normal periods, whereas TP was higher in the wet period. Spatially, concentrations in reservoir sections exceeded those in natural sections: natural sections had TP, TN, and NH3-N concentrations of 0.07–0.10, 0.25–0.50, and 0.025–0.250 mg·L−1, respectively, while reservoir sections had 0.12–0.17, 0.60–0.80, and 0.10–0.45 mg·L−1. These findings provide scientific references for water environment management in the Heihe River and similar inland river basins.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510071
Carbon source is a critical factor driving heterotrophic denitrification, yet the low carbon-to-nitrogen ratio (C/N) of livestock wastewater limits this process. This study developed novel composite carbon sources by combining corncob (CC) and polycaprolactone (PCL). Static carbon release and denitrification experiments were conducted to evaluate carbon release patterns and nitrogen removal performance. Results showed that the carbon release index (n) was below 0.45, indicating Fickian diffusion as the dominant release mechanism. The composite carbon source prepared at a CC:PCL mass ratio of 3:2 (denoted YP4) achieved a nitrate nitrogen removal efficiency of 94.76%, with effluent ammonia nitrogen meeting the discharge limits of GB 18596-2001. High-throughput sequencing revealed that YP4 increased the relative abundance of genera capable of denitrification and biopolymer degradation (e.g., Aeromonas, Novosphingobium, Bacteroides, and Clostridium sensu stricto), thereby enhancing heterotrophic denitrification and nitrogen removal. These findings provide a novel approach for selecting and preparing external carbon sources for biological heterotrophic denitrification of low C/N wastewater.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60710-4
Lignin pyrolysis is a promising route for sustainable production of high-value phenolic chemicals, yet the intricate radical reaction network remains a major bottleneck to optimizing product selectivity. This work constructs a standardized DFT computational database that systematically describes the fast pyrolysis of vanillyl alcohol at 823.15 K. The database features three key components: primary reaction pathways, thermodynamic energy barriers, and atomic-level electronic fingerprints. The dataset covers primary reaction pathways, secondary rearrangements, and both global and local reactivity indices of key intermediates. Notably, it innovatively integrates electronic-structure fingerprints, filling the gap in reaction-network–electronic-property correlation data. Standardized computational workflows and rigorous quality control ensure accuracy, consistency, and reproducibility. The public release of this dataset provides a reliable theoretical benchmark for mechanistic studies of lignin pyrolysis and offers foundational data support for rational design of new catalysts and refinement of reaction kinetic models. Ultimately, this database not only provides an important reference for data-driven catalyst development but also lays a theoretical foundation for precise regulation of lignin depolymerization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022702
This study systematically investigated the occurrence and vertical distribution of per- and polyfluoroalkyl substances (PFAS) in solid waste, leachate, and surrounding groundwater at a municipal solid waste landfill in Fuyang City, Anhui Province, China. A total of 23 PFAS were detected in solid waste, with total concentrations (∑PFAS) ranging from 7.95 to 172.28 ng·g⁻¹. Trifluoroacetic acid (TFA), an ultrashort-chain PFAS, was ubiquitous, contributing on average 59% to the total PFAS mass. PFAS composition varied with depth: long-chain PFAS dominated in middle and upper layers, while short-chain and ultrashort-chain PFAS were more abundant in deeper layers, indicating enhanced downward migration of shorter-chain compounds. Sulfonic acid PFAS exhibited increasing relative abundance with depth. Leachate ∑PFAS concentration was 14.35 μg·L⁻¹, dominated by short-chain compounds such as PFPrS and PFBS, consistent with the composition in bottom-layer waste. Groundwater surrounding the landfill contained multiple PFAS, with concentrations decreasing with distance from the landfill, confirming the landfill as a source of PFAS to the surrounding environment. Multivariate analyses (PCoA and Bray–Curtis dissimilarity) revealed that some groundwater samples closely resembled leachate in PFAS composition, suggesting direct impact via leachate migration. These findings underscore the role of landfills as significant reservoirs and sources of PFAS, particularly ultrashort-chain compounds, and highlight the need for improved leachate management to mitigate groundwater contamination.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051404
Rubber additives, such as 1,3-diphenylguanidine (DPG) and p-phenylenediamine antioxidants (PPDs), are widely used in the rubber industry and have been increasingly detected in aquatic environments. This study investigated the distribution characteristics and potential sources of seven typical rubber additives (DPG, 6PPD, IPPD, DPPD, CPPD, DNPD, and 77PD) and the transformation product 6PPD-Q in surface water of the Guangzhou section of the Pearl River, China. A total of 29 sampling sites were analyzed. Total concentrations of the target compounds ranged from 205 to 5400 ng·L−1, with a mean of (820±1100) ng·L−1. DPG was the dominant compound in both dissolved and particle phases, accounting for (99±1.9)% and (66±13)% of the total concentrations, respectively. Source analysis indicated that aquaculture, vessel navigation, agricultural runoff, and wastewater treatment plant discharges likely influence the occurrence of rubber additives in this river section. Risk quotient (RQ) assessment revealed that 6PPD-Q posed high ecological risk at all sampling sites (RQ > 1), while DPG exhibited moderate to high risk at most sites (RQ > 0.1). In contrast, 6PPD, IPPD, CPPD, and DPPD showed low ecological risk. These findings highlight the need for heightened attention to the ecological risks posed by 6PPD-Q and DPG in the Pearl River Basin and provide scientific data for pollution prevention and risk management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608013
Eutrophication and cyanobacterial blooms threaten aquatic ecosystems and drinking water safety globally. This study evaluated the efficacy of a compound algicide (PQGA-126, PAC, and red soil) combined with submerged plants (Vallisneria natans and Hydrilla verticillata) for suppressing blooms and restoring eutrophic water. Indoor static experiments used algae-laden water from Nanhu Lake, Gongqingcheng, Jiangxi. Six treatments were established: control, V. natans alone, H. verticillata alone, algicide alone, algicide + V. natans, and algicide + H. verticillata. Results demonstrated that combined treatments significantly reduced total nitrogen (TN), total phosphorus (TP), chlorophyll-a (Chl-a), and turbidity, markedly lowering eutrophication within a short period. The combined approach outperformed single-plant treatments, with algicide + V. natans achieving the greatest reduction in the comprehensive trophic state index. Additionally, the algicide significantly enhanced V. natans growth rate and H. verticillata catalase (CAT) activity, indicating species-specific physiological responses. These findings suggest that integrating compound algicide with submerged plants, particularly V. natans, offers a promising strategy for rapid and effective eutrophic water remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4031-6
Organic fluorophores operating in the second near-infrared (NIR-II, 1000–1700 nm) window are highly attractive for cancer phototheranostics. Yet, the advancement of aza-BODIPY-based NIR-II dyes remains challenging due to their limited spectral tunability and diminished fluorescence quantum yields (FLQY) under physiological conditions. Herein, we propose a rational donor-acceptor (D-A) molecular engineering strategy to construct an aza-BODIPY fluorophore, TPACN, featuring intramolecular charge transfer (ICT)-enhanced NIR-II emission and balanced photothermal performance. By introducing electron-rich triphenylamine (TPA) donors and peripheral cyano (–CN) acceptors, the optimized D-A coupling significantly strengthened the ICT effect, leading to broadened NIR absorption, a markedly red-shifted fluorescence peak at 1086 nm, and an exceptional fluorescence quantum yield of 1.55% in dichloromethane (DCM). When encapsulated in F127, TPACN nanoparticles (TPACN NPs) maintained a high aqueous FLQY of 0.20%, accompanied by a notable photothermal conversion efficiency (PCE) of 39% under 808 nm irradiation. The sterically twisted TPA units effectively alleviated aggregation-caused quenching (ACQ) and fine-tuned the excited-state energy dissipation pathways, realizing a synergistic balance between radiative (fluorescence) and non-radiative (heat) relaxation. Benefiting from these optimized photophysical properties, TPACN NPs achieved high-resolution NIR-I photoacoustic and NIR-II fluorescence dual-modal imaging, enabling accurate tumor visualization and efficient photothermal ablation in vivo. This work introduces a general design paradigm that exploits ICT modulation and steric engineering to overcome the intrinsic fluorescence bottleneck of aza-BODIPY systems, offering new molecular insights for the advancement of high-performance NIR-II dyes for precision phototheranostics.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60663-9
The catalytic hydrogenation of biomass-derived dimethyl succinate (DMS) to 1,4-butanediol (BDO) is a pivotal route for producing high-value C4 chemicals in green chemistry. Cu/SiO2 catalysts are known for high selectivity in hydrogenating ester groups, with performance correlated to copper species microstructure. Although calcination critically defines this active structure, systematic influence of calcination atmosphere remains underexplored. Here, Cu/SiO2 catalysts were prepared via urea-assisted hydrothermal method and calcined under different atmospheres to elucidate effects on physicochemical properties and hydrogenation performance. Comprehensive characterization (N2 physisorption, FT-IR, H2-TPR, XRD, TEM, N2O pulse chemisorption, XPS, NH3-TPD) revealed that calcination atmosphere profoundly alters metal-support interaction, regulating dispersion and chemical state of copper species. Specifically, air calcination promoted stronger metal-support interaction, enhancing copper dispersion and increasing proportion of key active Cu+ species. Consequently, air-calcined catalyst achieved 92.37% DMS conversion and 64.15% BDO yield under optimized conditions (210 °C, 5.0 MPa, WHSV 0.6 h−1, H2/DMS molar ratio 100). This work underscores calcination atmosphere engineering as potent strategy for optimizing metal-support interactions in heterogeneous catalysts for efficient hydrogenation.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3365-5
Conventional oil-water separation technologies, including centrifugation and flocculation, suffer from density-dependent limitations and secondary pollution, while membrane filtration with uniform wettability selectively recovers only one phase, leaving retained components unrecovered. Janus membranes with asymmetric wettability enable on-demand separation but their micro/nanoscale thickness restricts interfacial separation to microscopic domains. This work presents a Janus-channel-membrane (JCM) architecture that scales asymmetric wettability from micro/nanoscale to millimeter-scale spatial channels, constructed from a hydrophilic membrane and a hydrophobic membrane separated by a slit of a few millimeters. When surfactant-stabilized emulsions are delivered to the slit, purified water permeates rapidly through the hydrophilic membrane while oil is concurrently recovered at the hydrophobic membrane. The millimeter-scale channel width enhances enrichment and collision behavior of emulsion droplets via interference interactions between the membrane pair, producing substantial increases in oil and water recovery rates. The JCM demonstrates distinctive advantages for separating and recovering both phases from high-concentration-surfactant-stabilized emulsions. Multistage device configurations incorporating JCMs can further strengthen separation and recovery efficiency at multiple levels, offering transformative potential for industrial emulsion separation and recovery. This spatial configuration of membranes with contrary wettability at the millimeter scale addresses key bottlenecks in concurrent oil and water recovery from stable emulsions.