SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4244-0
Near-infrared perovskite light-emitting diodes (NIR-PeLEDs) suffer from poor operational stability, largely due to interfacial reactions at the electron-transport layer (ETL)/perovskite interface. Here, we introduce a zinc ion (Zn2+)-chelated hybrid ETL derived from a Zn2+-chelated polyethylenimine ethoxylated (PEIE) complex, which partially retains the surface properties of ZnO but exhibits significantly reduced oxygen defects and surface-adsorbed hydroxyl groups. This well-modulated surface promotes perovskite crystallization and mitigates interface-induced deprotonation of organic cations during device operation. Consequently, NIR-PeLEDs employing this hybrid ETL achieve a peak external quantum efficiency (EQE) of 20.1%, a high radiance of 652 W sr-1 m-2, and an exceptional T50 lifetime of 270.7 hours at a high current density of 100 mA cm-2, which is over five times that of devices based on conventional ZnO nanocrystal (NC) ETLs. Our results present an effective ETL strategy for operationally stable NIR-PeLEDs and thoroughly reveal the critical role of regulating interfacial reactions in stabilizing buried interfacial contacts. These findings provide valuable insights for advancing perovskite optoelectronic devices that suffer from interface-induced performance degradation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3691-9
Near-infrared (NIR) spectroscopy has significantly advanced NIR light sources, yet creating NIR emitters with optimal luminescence properties, high thermal stability, and adjustable emission peaks remains a critical challenge for future smart NIR devices. Here, we introduce a chemical unit cosubstitution strategy by incorporating Ca2+ and Sn4+ ions into the garnet structure. Through this approach, Y3−yCayGa4.95−ySnyO12:0.05Cr3+ (y = 0–1) phosphors were developed by modulating the A&C ligands, resulting in emission centers ranging from 708 to 768 nm. The modified local environment of Cr3+ accounts for the increased light intensity (2.71 times) and broadening observed. Furthermore, this study investigated the impact of varying Cr3+ concentrations (Y2.6Ca0.4Ga4.6−xSn0.4O12:xCr3+) on the production of high-performance phosphors. Compared with Y3Ga4.93O12:0.07Cr3+, the optimized phosphor exhibited exceptional external quantum efficiency (EQE = 34.96%). The luminescence enhancement is attributed to an increase in radiative transitions caused by octahedral Jahn-Teller distortion, whereas the notable thermal stability (91.3% at 423 K) is attributed to the presence of weak electron-phonon coupling (EPC) and oxygen vacancy (OV) defects. Finally, by combining it with a 450 nm blue LED chip, we constructed a near-infrared phosphor-converted LED (NIR pc-LED) device with superior electroluminescence efficiency (18.8% @ 100 mA), increasing the ultralow quenching rate (< 5% intensity loss after 30 days of operation) and demonstrating remarkable performance in plant lighting applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3588-2
The rapid evolution of aerospace technology necessitates the development of multi-functional composites that combine light weight, mechanical robustness, thermal protection/insulation, and electromagnetic interference (EMI) shielding. C/SiC porous ceramic composites are promising for thermal protection in hypersonic vehicles. Here, we report a facile strategy to fabricate Cf/SiC composite polymer-derived ceramics (PDCs) via re-pyrolysis of high-energy ball-milled polycarbosilane-vinyltriethoxysilane-graphene oxide (PVG) with Cf/SiC(rGO)p blend interleaves. In-situ generated honeycomb-like cellular structures and non-directional channels reduce density and increase porosity. High-quality SiO2 joints, formed from Si-dangling bonds, strengthen interfacial bonding via a brazing effect, while in-situ SiOC nanowires (SiOCnws) create a hierarchically enhanced network, improving fracture toughness and crack resistance. Multi-scale interfacial/dipole polarization enhances EMI shielding. The optimized Cf(0.2)/SiC(rGO) composite exhibits low density (1.49 g cm−3), high fracture toughness (6.32 MPa m1/2), hardness (7.18 GPa), compressive strength (72.67 MPa), and EMI shielding effectiveness of 58.31 dB. It maintains structural stability under butane blowtorch ablation at ~1300 °C for 3600 s. Porous variants show thermal conductivity of 0.211 W m−1 K−1 with 69.74% porosity. These multi-functional composites are promising for thermal protection systems in aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3630-2
This study demonstrates a dual-interface engineering approach for performance enhancement in perovskite-silicon tandem solar cells. By applying ethylenediamine dihydroiodide (EDAI2) to simultaneously modify both top and bottom interfaces of wide-bandgap perovskite layers, we achieve synergistic defect suppression and charge transport optimization. Time-resolved photoluminescence characterization reveals extended carrier lifetimes and improved spatial homogeneity in dual-modified perovskite films. The optimized single-junction wide-bandgap (>1.66 eV) perovskite solar cells attain a champion efficiency of 22.75% with enhanced operational stability. Implemented in perovskite-silicon tandem configuration, the devices achieve over 31% power conversion efficiency, validating the effectiveness of organic ligand-mediated dual-interface engineering in regulating carrier dynamics and advancing perovskite-based tandem photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3616-8
Negative stiffness (NS) structures exploit multi-stable mechanisms to achieve energy absorption, yet their practical application is limited by material and manufacturing constraints that compromise load-bearing capacity, reusability, and energy absorption efficiency. This study addresses these limitations by employing continuous carbon fiber reinforced thermoplastic polymers (CCFRTP) and three-dimensional (3D) printing to fabricate NS structures with cosine beam cells. A wet twisting method for continuous carbon fiber (CCF) was developed to enhance mechanical properties and elucidate failure behaviors and interfacial adhesion mechanisms. The resulting CCF/PLA/PVDF composites exhibited significant improvements in mechanical properties compared to untreated counterparts, with failure analysis revealing characteristic fiber breakage due to enhanced interfacial adhesion, as opposed to fiber pull-out and irregular fracture in untreated samples. A one-stroke path planning model was used to investigate bistability principles and energy absorption mechanisms. Displacement-controlled loading/unloading experiments assessed energy absorption in both energy-locked and repetitive modes. A dual-unit assembly structure was fabricated to validate the feasibility of a negative stiffness honeycomb structure. Composite layup simulations via Abaqus confirmed the deformation process and energy absorption mechanisms. The findings demonstrate that CCFRTP-based NS structures offer considerable potential for large deformation energy absorption applications in aerospace and naval fields.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604026
Polycyclic aromatic hydrocarbons (PAHs) are persistent organic pollutants ubiquitously present in soils, posing severe risks to ecosystems and human health. This study synthesized MIL-88A(Fe) via a hydrothermal solvent method and applied it to the photocatalytic degradation of phenanthrene-pyrene (PHE-PYR) composite contaminants in soil, investigating the adsorption-photocatalytic synergy. Results demonstrated that adsorption of PHE-PYR onto MIL-88A(Fe) was dominated by physical and monolayer surface adsorption, with a maximum adsorption capacity of 97.25 mg/kg. This strong adsorption increased pollutant concentration near active sites, accelerating photocatalytic degradation. Under optimal conditions—3% catalyst dosage, 40% soil water content, 60 min visible light irradiation, initial pollutant concentration of 200 mg/kg, and acidic soil—the total degradation efficiency reached 79.20%. Photoelectrochemical characterization revealed significant visible-light response (200–600 nm), a narrow bandgap of 3.04 eV, and favorable band structure facilitating efficient electron-hole separation. Quenching experiments identified superoxide radicals (·O2−) and holes (h+) as primary reactive species. GC-MS analysis of intermediates indicated that PYR undergoes hydroxylation, oxidation, and ring-opening to form PHE, which is further hydroxylated and oxidized, ultimately mineralizing to CO2 and H2O. This work provides an efficient strategy for remediating PAH-contaminated soils.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60622-0
Photocatalytic production of hydrogen peroxide (H2O2) from sustainable biomass-derived carbon catalysts offers a renewable route to valuable chemicals, yet the regulatory role of surface functional groups on reaction kinetics remains underexplored. Here, hydrothermal carbon spheres (CS) rich in oxygen-containing functional groups demonstrated a remarkably high H2O2 production rate of 653 μmol/(g·h) in both pure water and actual seawater, without any sacrificial agent. The catalyst also exhibited outstanding activity in visible-light-driven photocatalytic oxidation of benzylamine to imines, achieving 92% conversion and >99% selectivity. Comprehensive analysis revealed that CS was rich in surface oxygen-containing functional groups, a feature strongly associated with its high photocatalytic efficiency. The observed positive Zeta potential of CS in seawater likely diminished electrostatic repulsion against positively charged intermediates, facilitating their accumulation at the liquid-solid interface. This work proposes a strategic framework for developing metal-free photocatalysts from biomass, offering a sustainable pathway for photocatalytic applications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605018
To address the inadequacy of existing temporal emission allocation coefficients for oil storage, transportation, and sales sources in regions with distinct seasonal temperature variations, this study focused on a large oil depot in Northwest China. A method for establishing temperature-dependent hourly allocation coefficients for VOCs emissions was proposed, revealing a positive correlation between ambient temperature and emission coefficients. The coefficient peaked at 0.068 when temperatures exceeded 14 °C and dropped to a minimum of 0.007 below 8.5 °C. Annual VOCs emissions totaled 256.13 t, with summer contributing 108.89 t (42.51% of annual total) and winter only 12.54 t (4.90%), making summer emissions approximately 8.68 times higher than winter. Using CALPUFF dispersion modeling, dynamic source strength scenarios produced a maximum hourly concentration of 2242.7 μg/m³, a 55.12% increase over the constant source strength scenario (1445.8 μg/m³). The area of exceedance increased by 0.03 km², and the atmospheric environmental protection distance extended by 450 m, from 0 m to 450 m. These results demonstrate that conventional constant emission assumptions underestimate peak concentrations and protection distances, posing health risks to nearby residents. The study provides a scientific basis for localized emission regulation and improved environmental protection distance calculations.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605021
The digestate from anaerobic digestion of food waste is separated into solid residue and liquid filtrate. The filtrate retains high nutrient and carbon content, making it a viable resource for recovery. This study prepared biochar from food waste digestate residue and employed it as an electrode active material in a flow-electrode capacitive deionization (FCDI) system, with activated carbon as a control, to assess nitrogen and phosphorus removal from kitchen waste biogas slurry. ZnCl₂ modification significantly enhanced the biochar's specific surface area, adsorption capacity, capacitance, and conductivity. The optimal mass fraction of modified biochar in the electrode liquid was 7.5%. In simulated digestate, the FCDI system achieved removal efficiencies of 47.7% for NH₄⁺-N and 55.2% for reactive phosphorus (RP) over 12 hours. Performance ranking of electrode materials was activated carbon > ZnCl₂-modified biochar > unmodified biochar. In continuous operation with actual anaerobic digestion filtrate, maximum removal efficiencies were 32.2% for NH₄⁺-N and 26.2% for RP. The reduced performance in real digestate is attributed to organic foulants such as peptides and amino acids, which block ion-exchange membrane channels, increase membrane resistance, and impede ion transfer and charge transport, thereby diminishing deionization efficiency.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606003
Membrane separation technology, offering high separation efficiency, low energy consumption, and operational flexibility, is promising for lithium recovery. However, selective lithium extraction from complex matrices such as salt lake brines and battery leachates remains challenging. Traditional membrane development relies on empirical trial-and-error, suffering from low efficiency and the permeability-selectivity trade-off. This review systematically delineates machine learning (ML)-based frameworks for membrane material development, including high-throughput rational screening, inverse design of synthesis protocols, and high-fidelity performance prediction. We elucidate how advanced ML algorithms decipher structure-activity relationships at the molecular level, enabling breakthroughs in performance ceilings and guiding bottom-up fabrication of next-generation membranes. Critical challenges are assessed: scarcity of high-quality standardized datasets, limited model interpretability, and poor generalizability to industrial scales. Future directions emphasize physics-informed hybrid models, open-source global databases, and full-process system optimization to bridge laboratory innovation and industrial deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3823-4
The global demand for chlorine gas continues to rise, driven by its indispensable role in chemical synthesis, disinfection, and wastewater treatment. Electrocatalytic chlorine evolution from seawater presents a promising alternative to the energy-intensive chlor-alkali process, yet it is hampered by the competing oxygen evolution reaction and the sluggish kinetics of chlorine evolution on conventional catalysts. Here, we report a novel hollow porous CoNiSe2/NiSe2 heterostructure nanosheet array synthesized via ion exchange and calcination, which exhibits exceptional catalytic activity and selectivity for the chlorine evolution reaction in acidic seawater-like electrolytes. The unique hollow porous morphology provides a high specific surface area, facilitating mass transport and exposing abundant active sites. Crucially, the heterointerface between CoNiSe2 and NiSe2 promotes d-p orbital hybridization between Co/Ni 3d and Se 4p states, which lowers the reaction energy barrier for chlorine evolution. The catalyst achieves a low overpotential of 108 mV to reach a current density of 100 mA cm−2 in 4.0 M NaCl acidic medium, with excellent stability and Cl2 selectivity. This work demonstrates the potential of non-noble metal selenides as efficient and durable catalysts for chlorine production, offering a pathway toward more sustainable chlor-alkali technology.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60653-6
Carbon deposition caused by mass transfer limitations is a key challenge for traditional microporous ZSM-5 zeolites in coal tar catalytic cracking. To address this, benzene was used as a model compound. Parent ZSM-5 (NL-ZSM-5) was modified with tetraethylammonium hydroxide (TEAOH) to prepare hierarchical ZSM-5 zeolites with different mesopore sizes. Characterization (XRD, FT-IR, BET, TEM) confirmed successful mesopore introduction via selective desilication while retaining the MFI structure. At TEAOH concentration of 0.4 mol/L (ZSM-5-C), total pore volume increased from 0.24 to 0.43 cm3/g, and Brønsted acid amount increased from 0.28 to 0.67 mmol/g, with improved acid site accessibility. Catalytic experiments and carbon deposition analysis showed that hierarchical pore structure inhibits coking via a synergistic effect of diffusion enhancement and adsorption-site regulation. The coke amount of ZSM-5-C was 4.0%, only one-third of that of NL-ZSM-5 (11.9%). Molecular dynamics simulations confirmed that the diffusion coefficient of benzene in a 3.0 nm mesopore model is an order of magnitude higher than in a 2.0 nm model. Adsorption capacity decreases with increasing mesopore size, shortening residence time. Increasing temperature enhances diffusion but exponentially intensifies surface condensation reactions (Arrhenius effect), which dominates coke formation; hierarchical pores mitigate this negative effect. This research provides a theoretical basis for designing high-efficiency, coke-resistant catalysts for coal tar conversion.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026031103
Sintering ash washing wastewater from steel plants is characterized by high salinity, high chloride content, high thallium load, and coexistence of multiple metals, posing significant treatment challenges. This study employed thermodynamic simulation to elucidate the speciation and transformation of thallium in such wastewater, and systematically investigated a combined process of sulfide precipitation coupled with coagulation-flocculation. The results showed that at pH 9–10, thallium predominantly existed as Tl+. Under oxidizing conditions, the stable complex anion [TlCl4]− dominated at pH < 8.1, while at pH > 8.1, a mixed system of solid Tl2O3 and dissolved TlClO3 coexisted. Under optimized conditions (pH 12, 2.0% thallium removal agent, 1.0% multi-effect auxiliary agent), the thallium concentration in the wastewater decreased from an initial 9.58 mg·L−1 to 4.31 μg·L−1, meeting the stringent discharge limit of ≤5 μg·L−1. Concurrent removal of Cu, Zn, and Cd was achieved. The primary removal mechanism was sulfide precipitation, with lattice substitution between Tl+ and K+ serving as an auxiliary pathway. This study provides a practicable technical route for advanced treatment of high-chloride, high-thallium industrial wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.