SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4239-2
The sluggish kinetics of the oxygen evolution reaction (OER) remains a bottleneck for efficient water splitting. NiFe-layered double hydroxides (LDHs) are promising OER catalysts, but their performance is often limited by the high-spin state of Fe3+ and poor structural stability. Here, we report a series of amino acid-intercalated iron-rich NiFe-LDHs (AA-NiFe-LDHs) synthesized via a facile one-step coprecipitation method. Intercalation of glycine, alanine, and valine into the interlayer galleries expands the interlayer spacing and induces a partial transition of Fe3+ from high-spin to low-spin state, as confirmed by X-ray absorption spectroscopy and Mössbauer spectroscopy. The low-spin Fe3+ enhances the intrinsic catalytic activity by optimizing the adsorption energy of oxygen intermediates. Among the series, the glycine-intercalated sample (Gly-NiFe-LDH) exhibits the best OER performance in 1.0 M KOH, with an overpotential of 240 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, significantly outperforming the pristine NiFe-LDH (280 mV, 52 mV dec−1). Moreover, Gly-NiFe-LDH shows excellent long-term stability, retaining 95% of its initial activity after 24 h of chronopotentiometry at 10 mA cm−2. The intercalation also increases the electrochemically active surface area by 2.3-fold and reduces the charge transfer resistance from 12.5 Ω to 4.8 Ω. This work demonstrates that amino acid intercalation is an effective strategy to modulate the spin state of Fe3+ and enhance the OER performance of NiFe-LDHs, providing a new avenue for designing high-efficiency, low-cost electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4114-5
The precise and controllable synthesis of one-dimensional (1D) and two-dimensional (2D) heterostructures, coupled with the manipulation of their atomic and electronic configurations, is of paramount significance. However, due to the synthetic challenges associated with graphyne (GY) materials, their integration into 1D/2D heterostructures remains considerably difficult. Herein, we demonstrate a post-synthetic intercalation strategy for tellurium onto Ag(111), enabling the controllable fabrication of 1D-GY-nanowire/2D-AgTe-monolayers heterostructures. Scanning-probe microscopies are employed to characterize morphological evolution during the intercalation process. Scanning tunneling spectroscopy results confirm that AgTe monolayer intercalation induces interfacial decoupling of the graphyne nanowires. Density functional theory calculations demonstrate that work function-driven Fermi level modulation via interfacial charge engineering assigns the 1D-GY-nanowire/2D-AgTe-monolayers heterostructures as type-I heterostructures. Our work not only significantly advances the fundamental understanding of interfacial interactions in 1D/2D heterostructures but also presents a scalable strategy for designing heterostructures with tailored electronic functionalities, thereby opening new avenues for applications in advanced nanoelectronics and optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3865-1
Seawater electrolysis (SWE) is a reusable and convenient avenue for producing hydrogen, offering a promising solution to the energy crisis and global warming. However, poor electrolytic efficiency and irreversible corrosion caused by high concentrations of chlorine severely hinder the commercialization of SWE. To address these challenges, numerous strategies have been proposed in recent years, involving theoretical innovations, directional catalyst design, and electrolyser modification. This review provides a systematic summary of the chlorine-related challenges and solutions encountered in SWE. The chlorine-related theoretical knowledge and challenges in SWE systems are first emphasized. Subsequently, multiple anodic chloride suppression strategies are introduced from three aspects: directional regulation of oxygen evolution catalysts, optimization of electrolyte compositions, and ingenious upgrades of electrolytic cells. Finally, future challenges and development directions for large-scale application of SWE technology are explored. This review offers an in-depth analysis of the chlorine-related challenges encountered in the industrialization of SWE, aiming to accelerate the advancement of this technology toward practical applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010608
This study investigated the occurrence and distribution of 27 per- and polyfluoroalkyl substances (PFAS) in surface water and sediment of the Fuchun River, a tributary of the Qiantang River Basin. Surface water samples were analyzed using ultra-performance liquid chromatography coupled with high-resolution mass spectrometry. Total PFAS concentrations (∑PFAS) in surface water ranged from 30.04 to 105.26 ng/L, with mean and median values of 59.64 ng/L and 51.43 ng/L, respectively. The dominant compounds were perfluorooctanoic acid (PFOA), hexafluoropropylene oxide dimer acid (GenX), and perfluorobutanoic acid (PFBA). Concentrations generally decreased from upstream to downstream, consistent with previous studies. Notably, GenX levels were significantly elevated compared to earlier reports. In sediment, ∑PFAS concentrations ranged from not detected (ND) to 0.59 ng/g dry weight, with mean and median values of 0.14 ng/g and 0.11 ng/g, respectively. PFOA and perfluorooctanesulfonic acid (PFOS) were the primary sediment contaminants. Source apportionment indicated that industrial wastewater discharge and sewage treatment plant effluents were the main sources of PFAS in the river. Risk assessment using risk quotients suggested low ecological risks to aquatic organisms for most detected PFAS. However, the presence of short-chain and novel PFAS warrants further investigation due to potential unknown risks.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225215
CO2 dilution is a recognized strategy for combustion control, yet its detailed effects on CH4/H2 combustion under lean conditions remain insufficiently characterized. This study numerically investigated jet diffusion flames in a triangular nozzle burner, varying CO2 mixing ratios from 0% to 40%, equivalence ratios from 0.4 to 0.9, at 300 K and 101325 Pa. The standard k-ε turbulence model and non-premixed combustion model were employed, with grid independence verified. Results showed that increasing CO2 blending reduced peak flame temperature, flame height, and average furnace temperature from 1688 K (0% CO2) to 1344 K (40% CO2). CO2 inhibited forward reactions of CO with O and OH, reducing O2 consumption. NOx emissions decreased by up to 95.5% at φ=0.7 (from 6.7×10-5 to 3.03×10-6) and 94.3% at φ=0.9, compared to pure methane. Conversely, H2 enrichment (0% to 40%) raised peak temperature from 2018 K to 2199 K and shifted the peak location closer to the burner (from 1.16 m to 0.82 m), promoting more compact flames. In CH4/H2 mixtures, CO2 still effectively reduced NOx, though the effect slightly weakened with higher CO2 ratios. Controlling CO2 blending below 30% balances NOx reduction and combustion stability. The CH4/H2/CO2 ternary strategy enables coordinated regulation of temperature and pollutant emissions, offering a technical pathway for hydrogen-rich fuel applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021401
This study investigated the occurrence, distribution, sources, and ecological risks of 19 organophosphate triesters (OPEs) and 8 diesters (di-OPEs) in surface water and sediments from the Hangzhou section of the Qiantang River. Samples were analyzed using liquid chromatography-high resolution mass spectrometry. Concentrations of ΣOPEs in water ranged from 31.5 to 98.9 ng/L, and in sediments from 10.8 to 341 ng/g dry weight (dw). Σdi-OPEs ranged from 2.19 to 104 ng/L in water and 0.437 to 106 ng/g dw in sediments, indicating moderate to low contamination. TCIPP and TCEP dominated OPEs in water, while TEHP was the predominant OPE in sediments. DBP was the major di-OPE in water, and DPHP in sediments. Source apportionment via correlation and principal component analysis identified industrial production and human activities, including household, tire, plastic manufacturing, and agricultural practices, as primary sources. Ecological risk assessment revealed negligible risks for most OPEs in water, but notable risks in sediments: TEHP and EHDPP posed risks to crustaceans, and TPHP to algae. Moreover, combined toxicity at multiple sediment sampling sites raised concern, warranting further attention.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3979-3
The escalating prevalence of multidrug-resistant Pseudomonas aeruginosa (P. aeruginosa) infections necessitates novel antibacterial strategies. Here, we engineered lectin B (LecB)-targeted glyco-dots (TFP2F) via self-assembly of a photosensitizer (TFP2) possessing aggregation-induced reactive oxygen species (ROS) generation capability with fucose-modified tetraphenylethene glycoclusters (TPE-Fuc4), enabling P. aeruginosa-targeted antimicrobial photodynamic therapy and wound healing promotion. Three photosensitizers (TFP0–2) featuring an “A-D-A” electronic structure were synthesized, exhibiting broad absorption bands and near-infrared (NIR) fluorescence. Among these, TFP2 demonstrated superior Type-I/II ROS production (including ·OH, ·O2−, and 1O2), achieving potent phototoxicity against P. aeruginosa (MIC80 = 7.5 μM). Self-assembly with TPE-Fuc4 yielded glyco-dots TFP2F that facilitated LecB-mediated bacterial targeting, enhanced bacterial uptake, and significantly reduced the MIC80 to 2.5 μM against drug-resistant P. aeruginosa under light irradiation. In a murine P. aeruginosa-infected wound model, TFP2F treatment combined with light irradiation accelerated wound closure to <20% of the initial area by day 8 (vs. >40% in controls) and eliminated >95% of bacteria by day 2. This work presents a convenient strategy for constructing glyco-dots as a potent functionalized platform for precision, lectin-targeted antimicrobial photodynamic therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4035-5
Electrocatalytic CO2 reduction reaction (CO2RR) to formate offers a promising pathway for storing renewable electricity in chemical fuels and enabling carbon recycling. The development of efficient and stable catalysts for this specific pathway, however, remains a central challenge. Heteroatom doping can significantly tune the interaction between active sites and key intermediates, boosting catalytic performance. Conventional doping in Bi-based catalysts often relies on uncontrollable in-situ electrochemical processes, leading to ineffective bulk incorporation. Here, we present a simple pre-doping strategy that enables precise doping at surface active sites, thereby enhancing electrochemical performance. The resulting catalyst achieves >95% Faradaic efficiency for formate across 100–500 mA cm−2 in a flow cell and maintains >95% efficiency for over 70 h at 100 mA cm−2 in a membrane electrode assembly, outperforming pure Bi and Bi2S3. A solar-driven system further demonstrates a 4.4% solar-to-formate conversion efficiency. Mechanistic studies reveal that sulfur doping increases electron density, stabilizes the key *OCHO intermediate, and suppresses hydrogen evolution. These findings provide valuable insights into the precise pre-doping modulation of surface active sites for designing highly efficient and stable CO2RR catalysts.