SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4302-9
The pre-deposited lead iodide (PbI2) film in two-step inverted perovskite solar cells (PSCs) often exhibits a dense structure, which impedes the diffusion and reaction of organic ammonium salts, leading to unreacted PbI2 residues and compromised device performance. To address this, 2,4-oxazolidinedione (OD) is introduced as a molecule additive into the PbI2 precursor solution. Owing to its stronger coordination with PbI2, OD effectively modulates its crystallization behavior, resulting in a porous structure. This porous structure significantly facilitates the diffusion and infiltration of organic ammonium salts, thereby minimizing PbI2 residue and enhancing the completeness of the perovskite conversion. Furthermore, OD and the constructed porous network jointly retard the crystallization kinetics of perovskite, promoting the formation of perovskite films with improved crystallinity and preferred crystal orientation. Therefore, the optimized PSCs achieve a power conversion efficiency (PCE) of 26.31%, and demonstrate excellent operational stability, retaining 90.24% of initial PCE for 1500 h at 25°C and 90.47% after 1000 h at 65°C. The champion device exhibits a VOC of 1.197 V, a JSC of 26.28 mA cm-2, and an FF of 83.58%, with negligible hysteresis. This study presents a straightforward yet effective approach to advancing the performance and stability of inverted PSCs fabricated via the two-step method.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3803-8
The molecular copolymerization of donor-acceptor (D-A) interactions has been effectively utilized to modulate the charge transfer dynamics in polymeric carbon nitride (PCN) photocatalysts. Herein, a D-A configured photocatalyst (TPCN) was constructed by copolymerizing 4,4’,4’’-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT) as the electron donor with triazine units (electron acceptor). The unique propeller structure of TAPT, combined with the triazine framework, expanded the π-conjugated system and induced a strong built-in electric field (BIEF) across the D-A configuration. Theoretical calculations and transient absorption spectroscopy revealed that this synergistic effect facilitated intramolecular charge separation and widened the range of light absorption, indicating accelerated charge transfer and suppressed recombination in TPCN. The optimized TPCN3 sample exhibited dramatically enhanced photocatalytic H2O2 production (1.74 mmol g−1 h−1), representing a 13.4-fold increase over pristine PCN. Additionally, the TPCN3 sample also exhibited significantly faster degradation kinetics than PCN counterpart toward various emerging contaminants. This work demonstrates a promising strategy for designing efficient metal-free photocatalysts for sustainable H2O2 production and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3658-1
Organic-inorganic hybrid copper(I) halide semiconductors have attracted extensive attention for applications in phosphor-converted white light-emitting diodes (pc-WLEDs), X-ray imaging, and photodetectors because of their superior photo/radioluminescence, structural diversity, and eco-friendliness. In previous work, a strategy combining coordinated anionic inorganic modules with cationic derivatives yielded highly efficient blue-emitting hybrids, but synthesis complexity limited practical use. Here, we report a facile, efficient, and rapid solution-based ultrasonic treatment method for synthesizing high-performance blue-emitting phosphors using inexpensive, commercially available tetraethylammonium halides (TEAX, X = Cl, Br, I). The synergistic interplay of ionic and covalent bonds in these compounds endows them with a high photoluminescence quantum yield (PLQY) of 70% and excellent stability. These materials exhibit thermally activated delayed fluorescence (TADF), delivering outstanding performance in pc-WLEDs and X-ray imaging. Their exceptional properties highlight significant potential for use in optoelectronic devices and X-ray scintillators. This work provides an important reference for rapid synthesis of high-performance copper(I) halide hybrid phosphors and paves the way for commercial application.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4022-7
Transition metal nitrides (TMNs) have emerged as promising alternatives to noble metals in electrocatalysis due to their noble metal-like electronic structures, high conductivity, low cost, and robust chemical stability against corrosion and oxidation under harsh conditions. The rational design and controlled synthesis of TMNs with distinct structures are crucial for developing highly efficient electrocatalysts. This review comprehensively summarizes representative synthetic strategies for TMNs, including direct nitridation, solid-state reaction, sol-gel assisted reaction, and wet-chemical reaction. It presents distinct structural characterizations and demonstrates their advances in electrochemical applications. Finally, the remaining challenges and future research directions for exploring TMNs with well-defined structures are proposed, aiming to guide the development of high-performance electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3760-y
Layered chalcogenide compounds have attracted considerable attention for optoelectronic applications due to their rich structural diversity and unique physical properties, including high carrier mobility, ferromagnetism, ferroelectricity, and outstanding optoelectronic and thermoelectric performance. Their tunable bandgaps and strong light absorption render them highly suitable for next-generation photodetectors. However, the environmental instability of many 2D chalcogenides poses a critical challenge for practical applications. In this work, we report a high-performance, polarization-sensitive photodetector based on an air-stable ternary chalcogenide FeIn2Se4. Angle-resolved polarized Raman spectroscopy reveals that the four characteristic Raman modes exhibit a 60° periodic variation in intensity, highlighting the material's pronounced in-plane anisotropy. Benefiting from its strong absorption over a broad spectral range (510–1028 nm), the FeIn2Se4-based device demonstrates reliable photoresponse under multiple excitation wavelengths (405, 473, 515, and 638 nm), showcasing its wideband detection capabilities. Furthermore, XPS measurements after prolonged air exposure confirm the enhanced chemical stability of FeIn2Se4 compared to binary chalcogenides. These findings demonstrate that 2D ternary FeIn2Se4 is an excellent candidate for advanced anisotropic optoelectronic devices, offering broadband photodetection, robust polarization sensitivity, and excellent environmental resilience.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508004
Industrial processes generate substantial low-grade waste heat and cold, which can be harnessed via thermoelectric generators (TEGs) based on the Seebeck effect. However, the low-voltage output of TEGs poses application challenges. This study investigates a TEG-driven electrodeposition system for efficient treatment of low-concentration copper-containing wastewater from electroplating, integrated circuit, and energy industries. The TEG system, comprising two series-connected semiconductor modules, achieved a maximum power of 0.36 W at a temperature difference (ΔT) of 130 °C. Optimal operating parameters for the coupled system were determined: ΔT = 90 °C, counter-current flow (two-side inlet), flow rate of 20 mL·min⁻¹, initial Cu²⁺ concentration of 500 mg·L⁻¹, and electrode gap of 0.7 cm. Under these conditions, after 60 min of electrodeposition, copper removal efficiency reached 99.42%, current efficiency was 67.93%, and the energy conversion efficiency of the TEG-electrodeposition system was 36.96%. The system also treated real copper-containing wastewater, achieving 95.83% removal within 100 min. Characterization via SEM, XRD, and XPS revealed that the electrodeposited product consisted of metallic copper and cuprous oxide, with metallic copper accounting for approximately 60%. This work provides a promising approach for utilizing industrial waste heat and cold to achieve low-energy, high-efficiency treatment of heavy metal wastewater.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604026
Polycyclic aromatic hydrocarbons (PAHs) are persistent organic pollutants ubiquitously present in soils, posing severe risks to ecosystems and human health. This study synthesized MIL-88A(Fe) via a hydrothermal solvent method and applied it to the photocatalytic degradation of phenanthrene-pyrene (PHE-PYR) composite contaminants in soil, investigating the adsorption-photocatalytic synergy. Results demonstrated that adsorption of PHE-PYR onto MIL-88A(Fe) was dominated by physical and monolayer surface adsorption, with a maximum adsorption capacity of 97.25 mg/kg. This strong adsorption increased pollutant concentration near active sites, accelerating photocatalytic degradation. Under optimal conditions—3% catalyst dosage, 40% soil water content, 60 min visible light irradiation, initial pollutant concentration of 200 mg/kg, and acidic soil—the total degradation efficiency reached 79.20%. Photoelectrochemical characterization revealed significant visible-light response (200–600 nm), a narrow bandgap of 3.04 eV, and favorable band structure facilitating efficient electron-hole separation. Quenching experiments identified superoxide radicals (·O2−) and holes (h+) as primary reactive species. GC-MS analysis of intermediates indicated that PYR undergoes hydroxylation, oxidation, and ring-opening to form PHE, which is further hydroxylated and oxidized, ultimately mineralizing to CO2 and H2O. This work provides an efficient strategy for remediating PAH-contaminated soils.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225204
Cobalt-doped silica aerogel (Co@Si-A) catalysts were synthesized via a one-step sol-gel method and applied for peroxymonosulfate (PMS) activation to degrade tetracycline (TC). The catalyst with 25 wt% cobalt doping (25Co@Si-A) exhibited superior catalytic performance, achieving 98.97% TC degradation within 30 min under specified conditions (TC 10 mg/L, 100 mL). Brunauer-Emmett-Teller (BET) analysis revealed a high specific surface area and well-developed porous architecture with nano-confined spaces. The 25Co@Si-A/PMS system demonstrated outstanding adaptability across a broad pH range (5–9), maintaining >95% degradation efficiency, and showed strong resistance to sulfate and nitrate ions. In real water matrices, degradation efficiency remained around 80%. After five consecutive cycles, the system retained 82.33% degradation efficiency, with cobalt ion leaching of only 23.7 μg/L in the first cycle, indicating excellent stability. Mechanistic studies using electron paramagnetic resonance (EPR), radical quenching, and probe compound tests confirmed a synergistic radical and non-radical pathway. The primary reactive species were sulfate radicals (SO4•−), hydroxyl radicals (•OH), and singlet oxygen (1O2), with contributions of 58.53%, 9.79%, and 31.68%, respectively. Electrochemical tests indicated that 25Co@Si-A exhibited superior charge transfer compared to Co3O4, attributed to the nano-confined effect of the silica aerogel, which enhanced Co(II)/Co(III) redox cycling and PMS activation. This research provides a promising strategy for utilizing silica aerogel-based catalysts in advanced oxidation processes for water treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506084
Groundwater is a vital drinking and irrigation source in the loess regions of northwestern China. In Guyuan, a densely populated area in southern Ningxia, systematic assessments of groundwater pollution risks are lacking. This study collected 60 groundwater samples and employed the Nemerow index, heavy metal pollution index (HPI), and health risk assessment models to evaluate pollution levels and health risks of eight elements including Cr, As, and Hg. Results show that the groundwater is generally Class IV quality, with a mean TDS of 1350.9 mg·L−1. Average concentrations of As, Cr, and Mn are 4.39, 29.87, and 45.77 μg·L−1, respectively. The Nemerow index indicates moderate pollution. The mean HPI is 10.56, but a local sample (PS1-51-下) reaches 36.15, indicating severe pollution. Health risk assessment reveals that carcinogenic risks from Cr and As for adults and children are 8.037×10−6 a−1 and 3.863×10−6 a−1, respectively, below US EPA limits but above recommended levels by Swedish and Dutch agencies, with children at higher risk. Hydrogen and oxygen isotopes and principal component analysis suggest that groundwater is primarily recharged by atmospheric precipitation. Cr, Zn, and Mn mainly originate from regional copper ore belts, coal mining, and agricultural activities. This study fills a gap in multidimensional groundwater assessment in populated loess areas, identifies pollution characteristics distinct from typical loess regions, and provides a scientific basis for regional water resource risk management and sustainable development.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102002
The ultraviolet/chlorine (UV/Cl2) advanced oxidation process generates multiple radical species, enabling synergistic disinfection. However, the systematic influence of UV intensity on process performance remains inadequately characterized. This study investigated UV intensities from 0.25 to 2.0 mW·cm−2, assessing chlorine photolysis kinetics, bacterial inactivation, and disinfection by-product (DBP) formation. Results demonstrate that inactivation efficiency is not solely governed by total UV energy but is co-regulated by reaction kinetics and mass transfer. Increasing UV intensity accelerated chlorine photolysis by 33.7%–277.8%, elevating steady-state concentrations of hydroxyl radicals and chlorine radicals by factors of 1.6–3.8 and 1.3–3.2, respectively, thereby enhancing initial inactivation rates. However, higher intensities reduced cumulative chlorine exposure (CT value) to 14.3%–55.7% of baseline, causing overall inactivation to first increase then decrease. At a fixed UV dose of 150 mJ·cm−2, an intensity of 1.0 mW·cm−2 achieved optimal 6.5-log inactivation of Escherichia coli and the lowest bacterial reactivation rate (0.07%). Common water constituents (HCO3−, Cl−, natural organic matter) inhibited disinfection, with natural organic matter exerting the strongest suppression (2.7-log reduction). Notably, 1.0 mW·cm−2 exhibited the greatest resistance to interference. Elevated intensity reduced total organic halogen formation from 33.7 μg·L−1 to 19.0 μg·L−1. Balancing disinfection efficacy and DBP risk, 1.0 mW·cm−2 is identified as the optimal UV intensity for the UV/Cl2 process in sand-filtered water treatment.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225225
The non-Newtonian rheological properties of plastic melts are critical for regulating plastic processing, molding, and recycling processes, ensuring processing stability and product performance. However, rheological data for commonly used plastics and their blends remain incomplete. This study combined experimental testing and theoretical modeling to investigate the rheological behaviors of four pure plastics—polypropylene (PP), polyethylene (PE), polystyrene (PS), and acrylonitrile-butadiene-styrene copolymer (ABS)—and three binary blend systems: PE/ABS, PP/ABS, and PS/ABS. Rheological tests were conducted using a rheometer over a shear rate range of 0.1–100 s⁻¹ and temperatures from 180°C to 250°C. Results showed that the flow behavior index n was less than 1 for all samples, and apparent viscosity decreased significantly with increasing shear rate, indicating clear shear-thinning behavior. The consistency coefficient K followed the Arrhenius relationship with temperature, and melt viscosity decreased as temperature increased. The study quantitatively characterized the relationship between the mass fraction m (0.5 < m ≤ 1) of the main component in binary blends and melt viscosity. Based on experimental data, a component correction term was introduced into the traditional power-law model to construct a constitutive equation that simultaneously describes the effects of shear rate, temperature, and component fraction on melt viscosity. The average relative error between model predictions and experimental values was only 5.90%. These rheological data and the modified constitutive equation provide important theoretical support and data reference for optimizing process parameters in waste plastic recycling and injection molding.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509051
Recyclables constitute a significant fraction of municipal solid waste (MSW) and hold substantial potential for resource utilization and greenhouse gas (GHG) emission reduction, contributing to carbon peak and carbon neutrality goals. However, reported GHG emission factors (EFs) for various recyclables vary widely across databases and literature, ranging from -19,110 to -125 kgCO2-eq·t⁻¹, with significant differences both among categories and within the same category, complicating accurate accounting. This study systematically integrates literature data on EFs for different recyclable categories, focusing on identifying factors causing intra-category variability. Data were collected from global databases (ecoinvent, WARM, CPCD, NAEI) and peer-reviewed studies over the past two decades, normalized to a functional unit of 1 tonne of recyclable. Statistical analysis (mean ± standard deviation) provided reference ranges for each category. Results show paper recyclables EFs range from -3,140 to 270 kgCO2-eq·t⁻¹, with corrugated cardboard and writing paper exhibiting higher absolute values than packaging paper due to structural strength and resource value. Plastic recyclables EFs range from -3,096 to -566 kgCO2-eq·t⁻¹, with EPS showing the highest reduction potential, followed by PET and PVC, then HDPE, LDPE, PP, and other plastics. Key influencing factors include functional unit definition, accounting scenario, system boundary, electricity emission factor selection, and calculation assumptions. The study recommends selecting EFs matching the specific accounting scenario and performing error analysis. Data gaps remain for LDPE, EPS, and other plastics, necessitating further experimental or field data. To enhance accuracy, calibration methods such as process-level and life-cycle inventory data calibration are proposed. This work provides a scientific basis for EF selection and calibration in GHG accounting of recyclables.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60652-4
The performance of industrial zeolite catalysts, exemplified by fluid catalytic cracking (FCC) catalysts, is governed by microscopic behaviors including mass transfer, acidity, and coking. Conventional characterization techniques such as XRD, N2 physisorption, and TPD provide bulk-averaged or static ex situ information, failing to resolve dynamic processes under realistic reaction conditions. Recent advances in super-resolution fluorescence imaging enable nanoscale visualization of these key processes. This review systematically summarizes three critical applications: (1) Mass transfer diffusion: heterogeneous diffusion of reactant molecules within hierarchical pore networks is revealed, quantifying diffusion barriers and tortuosity. (2) Acid site accessibility: nanoscale localization of acid sites and their accessibility is achieved, correlating with catalytic activity. (3) Coking behavior: spatiotemporal evolution of coke species is identified, linking coke precursors to deactivation. The review elaborates how super-resolution imaging deepens understanding of fundamental catalytic mechanisms, providing theoretical support for rational design of high-performance catalysts through pore structure optimization, acid site regulation, and coking suppression. Current challenges and future directions are discussed, emphasizing the need for in situ correlation with catalytic performance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025081103
Nitrous acid (HONO) is a critical precursor of hydroxyl radicals (·OH) in the atmosphere, influencing oxidative capacity and secondary pollutant formation. However, model simulations often underestimate HONO concentrations, and its role in nitrate formation remains unclear. This study investigates a typical winter haze episode in Guangzhou (January 2021, peak PM2.5: 243.0 μg·m−3) using observational data and a box model to quantify HONO sources and assess their impact on ·OH and particulate nitrate. HONO concentrations increased from (1.0±1.0) μg·m−3 during clean periods to (9.2±3.8) μg·m−3 during polluted periods, while nitrate rose from (6.4±3.4) to (43.3±20.0) μg·m−3 (6.8-fold). Incorporating seven additional HONO sources improved simulated daytime HONO from (0.3±0.1) to (6.5±2.3) μg·m−3, matching observations. Source apportionment showed direct vehicle emissions dominated (49.7%), followed by heterogeneous photosensitized reaction of NO2 on aerosol surfaces (23.0%), ground surface reaction (10.7%), and nitrate photolysis (8.7%). With optimized HONO, simulated daytime ·OH increased from (0.6±0.3)×10^6 to (1.5±0.8)×10^6 molec·cm−3 (1.2-fold), and nitrate production via ·OH+NO2 increased from (3.4±1.2) to (15.3±8.5) μg·m−3·h−1 (3.5-fold). The simulated-to-observed nitrate ratio improved from 21% to 81%. Sensitivity tests indicated that setting nitrate photolysis enhancement to 100 times gaseous nitric acid yielded better HONO and nitrate simulations. This study underscores the importance of refining HONO sources for accurate simulation of atmospheric oxidation and nitrate formation, aiding pollution control strategies.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606007
Cobalt-aluminum spinel metal oxides derived from hydrotalcite were synthesized via hydrothermal, coprecipitation, and sol-gel methods, and their catalytic performance for NO oxidation was systematically evaluated. Characterization by X-ray photoelectron spectroscopy (XPS), O2 temperature-programmed desorption (O2-TPD), H2 temperature-programmed reduction (H2-TPR), and Raman spectroscopy revealed that the synthesis method significantly influences the surface Co2+/Co3+ ratio, which in turn modulates the formation of surface oxygen vacancies. The hydrothermally synthesized catalyst (CoAlO-H) exhibited the highest density of surface oxygen vacancies, leading to enhanced adsorption and activation of gaseous oxygen and superior NO oxidation activity compared to coprecipitation (CoAlO-C) and sol-gel (CoAlO-S) counterparts. Mechanistic studies using NO-TPD, NO+O2-TPD, and in situ diffuse reflectance infrared Fourier transform spectroscopy (in situ DRIFTS) identified nitrates as key intermediates. Notably, CoAlO-C and CoAlO-S followed the Langmuir-Hinshelwood (L-H) mechanism, whereas CoAlO-H operated via both L-H and Mars-van Krevelen (MvK) mechanisms. The exceptional performance of CoAlO-H is attributed to its abundant surface oxygen vacancies, high surface oxygen mobility, and low decomposition temperature of reaction intermediates. These findings provide a rational basis for designing efficient non-precious metal catalysts for NO oxidation in diesel exhaust aftertreatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3937-7
Triple-negative breast cancer (TNBC) remains a formidable clinical challenge due to its high invasiveness and adaptive resistance. We report a bio-mimetic nanoplatform (HMPB-GOx@HSA-Cu2+) integrating starvation therapy, Fenton/Fenton-like catalysis, and mild photothermal therapy (mPTT) for synergistic TNBC treatment. The nanoreactor comprises a hollow mesoporous Prussian blue (HMPB) core loaded with glucose oxidase (GOx), encapsulated in a human serum albumin (HSA) shell covalently functionalized with Cu2+ ions. This design enables spatiotemporal control of Cu2+-mediated Fenton catalysis, responding to the tumor microenvironment (TME) to generate cytotoxic hydroxyl radicals (·OH). GOx catalyzes glucose depletion, elevating H2O2 levels and acidity, thereby enhancing catalytic efficiency. Concurrently, mPTT at ~43–45°C accelerates the Fenton reaction and suppresses heat shock protein (HSP) expression, overcoming thermal tolerance via ATP depletion. In vitro and in vivo studies demonstrate significant anti-tumor efficacy through reactive oxygen species (ROS) accumulation and metabolic disruption, with excellent biocompatibility. This work presents a highly integrated strategy for precise TNBC therapy, addressing limitations of conventional monotherapies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510081
Electrochemical two-electron oxygen reduction (2e−ORR) for hydrogen peroxide (H2O2) synthesis faces challenges of low cathodic catalytic efficiency and complex catalyst preparation. This study prepared nitrogen-vacancy (Nv) rich carbon nitride via one-step pyrolysis, composited with carbon nanotubes (CNT), and loaded onto graphite felt (GF) to fabricate a non-precious metal gas diffusion electrode Nv-C3N4-CNT/GF. The electrode exhibited a three-dimensional fibrous skeleton with interconnected micro-nano hierarchical pores, facilitating efficient electron transport. Electrochemical impedance spectroscopy revealed a low charge transfer resistance of 13.26 Ω, indicating superior electrocatalytic activity and charge transfer efficiency. Single-factor experiments and response surface methodology (RSM) optimization determined optimal conditions: calcination temperature 300 °C, catalyst mass ratio 3:1, Nv-C3N4-CNT loading 0.1 g, current density 40 mA·cm−2, pH 7, and aeration rate 0.1 L·min−1. Under these conditions, H2O2 accumulation reached 1622.73 mg·L−1 after 90 min, which was 1.3 and 1.5 times higher than g-C3N4-CNT/GF and CNT/GF electrodes, respectively. Stability tests showed that after 6 cycles, H2O2 production remained at 1400.52 mg·L−1, and within 960 min, the maximum production reached 2014.04 mg·L−1 with a highest Faradaic efficiency of 54.86%. These results demonstrate the electrode's potential for cyclic use. This study provides a new approach for developing efficient, low-cost electrodes for electrosynthesis of H2O2, offering a reference for green H2O2 production.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60615-3
Co-pyrolysis of oil-rich coal and biomass is a promising route to enhance oil and gas production, yet the underlying synergistic mechanisms remain poorly understood. This study investigates the effect of hydrothermal pretreatment (HTP) on the co-pyrolysis of Huangling coal (H) and enzymatic hydrolysis lignin (E). Raw and pretreated samples were characterized via proximate/ultimate analysis, SEM, ICP-OES, and 13C-NMR. Fixed-bed pyrolysis experiments were conducted to evaluate synergistic performance. Results show that HTP reduces oxygen content, develops pore structure, and increases concentrations of inorganic metal ions (Ca, K, Fe) in the aqueous phase. Structural modifications bring the carbon skeleton of E closer to that of H, with increased bridge carbon ratio and improved thermal stability, aligning pyrolysis temperature ranges. For the H/E blend (8:2) after 24 h HTP, tar yield increases by 80.52% compared to untreated blend, with significant rises in aliphatic compounds and monocyclic aromatic hydrocarbons. Gas yields of H2, CO, and CH4 increase by 5.47%, 10.98%, and 9.27%, respectively, while CO2 and pyrolysis water generation are inhibited (water yield decreases by 93.98%). Semi-coke pore structure becomes more developed. The enhanced synergistic effect is attributed to a multi-fold mechanism of 'component interaction-structural modification-catalytic cracking'. These findings provide theoretical support for developing technologies to improve co-pyrolysis of oil-rich coal and biomass, advancing low-carbon, high-quality utilization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040104
The oxidative transformation of 2,6-dichlorophenol (2,6-DCP) was investigated in three typical zonal soils: black soil, red soil, and brown soil. Results demonstrated that 2,6-DCP underwent oxidative coupling in all soils, yielding hydroxylated polychlorinated diphenyl ethers (OH-PCDEs) and hydroxylated polychlorinated biphenyls (OH-PCBs) as primary products. The highest oxidative efficiency occurred in black soil, with approximately 85.1% of 2,6-DCP transformed within three days. In contrast, red and brown soils exhibited lower efficiencies, indicating a strong dependence on soil properties. Thermodynamic analysis revealed that the oxidative coupling reaction is endothermic, with elevated temperatures favoring reaction progress. Furthermore, soil microorganisms and dissolved oxygen were identified as critical controlling factors, acting synergistically to drive the reaction. This study provides the first evidence of natural oxidative coupling of 2,6-DCP in soil, forming OH-PCDEs and OH-PCBs. These findings offer significant scientific insight into the environmental fate of halogenated phenolic pollutants in terrestrial systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051404
Rubber additives, such as 1,3-diphenylguanidine (DPG) and p-phenylenediamine antioxidants (PPDs), are widely used in the rubber industry and have been increasingly detected in aquatic environments. This study investigated the distribution characteristics and potential sources of seven typical rubber additives (DPG, 6PPD, IPPD, DPPD, CPPD, DNPD, and 77PD) and the transformation product 6PPD-Q in surface water of the Guangzhou section of the Pearl River, China. A total of 29 sampling sites were analyzed. Total concentrations of the target compounds ranged from 205 to 5400 ng·L−1, with a mean of (820±1100) ng·L−1. DPG was the dominant compound in both dissolved and particle phases, accounting for (99±1.9)% and (66±13)% of the total concentrations, respectively. Source analysis indicated that aquaculture, vessel navigation, agricultural runoff, and wastewater treatment plant discharges likely influence the occurrence of rubber additives in this river section. Risk quotient (RQ) assessment revealed that 6PPD-Q posed high ecological risk at all sampling sites (RQ > 1), while DPG exhibited moderate to high risk at most sites (RQ > 0.1). In contrast, 6PPD, IPPD, CPPD, and DPPD showed low ecological risk. These findings highlight the need for heightened attention to the ecological risks posed by 6PPD-Q and DPG in the Pearl River Basin and provide scientific data for pollution prevention and risk management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3977-8
Single quantum well (single-QW) two-dimensional (2D) perovskites are poised to revolutionize optoelectronic devices owing to their superior stability and optoelectronic properties. However, solution-processed 2D perovskites typically suffer from disordered multiple-QW structures, leading to inconsistent device performance. Here, we introduce a solvent-hydrolysis-driven method to control crystallization kinetics, yielding highly ordered single-QW 2D perovskite films. Dimethylamine (DMA), generated from the hydrolysis of N,N-dimethylformamide (DMF), serves as a critical mediator, preventing cluster aggregation and ensuring a uniform colloidal distribution. This approach circumvents the formation of a heterogeneous intermediate phase, thereby promoting the formation of a homogeneous (DMA,MA)PbI3 phase, which is essential for single-QW film development. The resultant photodetector exhibits outstanding performance, with a responsivity of 1153 mA/W and a detectivity of 6.98 × 10^12 Jones, along with excellent photostability under ambient conditions. These attributes render it ideal for photoelectric imaging sensors and large-scale integration. Our findings establish a scalable, solution-processed strategy for high-performance 2D perovskite materials, opening new avenues for advanced optoelectronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3999-x
The integration of photochromism (PhCh) and persistent luminescence (PersL) into a single material remains a formidable challenge due to the complex role of defects in modulating optical properties. Here, we employ structurally simple CsX (X = Cl, Br) nanocrystals (NCs) as a model system to elucidate the relationship between defects and optical behaviors. We demonstrate that CsX NCs accommodate two distinct types of chlorine vacancy defects upon X-ray irradiation: intrinsic vacancies from synthesis and X-ray-induced vacancies. This dual-defect engineering enables reversible blue coloration under X-ray irradiation (20–70 kV), attributed to recoverable chlorine vacancies that are rapidly eliminated by visible light within 30 s. The photochromic behavior exhibits excellent cycling stability with a color difference (ΔRL1) of 56.9% and a recovery rate (ΔRL2) of 98.1%. Furthermore, Br− incorporation deepens the energy level of intrinsic chlorine vacancies from 0.47–0.71 eV to 0.83 eV, resulting in intense persistent luminescence lasting over 30 minutes. These dual-mode PhCh–PersL characteristics position CsX NCs as promising candidates for X-ray colorimetric imaging and dynamic anti-counterfeiting applications. Our findings establish a defect-oriented design principle extendable to other halide systems, advancing the development of multifunctional photonic materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60669-X
Dry reforming of methane (DRM) converts CH4 and CO2 into syngas with a unity H2/CO ratio, but suffers from catalyst deactivation via sintering and carbon deposition at high temperatures. This study addresses these challenges by employing UiO-66 as a precursor to modify Pt-based catalysts. A series of Pt/CeO2-ZrO2 catalysts were synthesized via incipient wetness impregnation using supports with varying Ce/Zr ratios prepared hydrothermally. Comprehensive characterization—including CO2-TPD, CH4-TPD, XPS, XAFS, in situ DRIFTS, TG, and Raman spectroscopy—revealed a volcano-type correlation between DRM performance and Ce/Zr ratio. Optimal activity and stability were achieved with Pt/3CeO2-ZrO2 (Ce/Zr = 3:1). This catalyst features highly dispersed platinum, primarily as single atoms and thermally stable PtOx clusters. It exhibits the highest concentration of Ce3+ and Zr3+ species, abundant oxygen vacancies, and high defect density, indicating strong metal-support interaction. Mechanistically, stable DRM is facilitated by oxygen-assisted CH4 dissociation and hydrogen-assisted CO2 dissociation. At 800 °C, CH4 and CO2 conversions reached 86% and 93%, respectively, with H2/CO ratio near unity. A 10 h stability test showed no detectable carbon deposition. These results confirm that the catalyst enhances reaction kinetics while demonstrating superior activity, stability, and resistance to coking and sintering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4208-8
Sodium-ion batteries (SIBs) are emerging as a cost-effective alternative to lithium-ion batteries due to the abundance of sodium resources. Among cathode materials, P2-type layered oxides (Na_xTMO_2) offer high ionic conductivity and rate capability but suffer from low initial sodium content and Na+/vacancy ordering, leading to structural degradation and capacity fading. This study proposes a synergistic strategy combining high sodium content with Li/Mg co-doping to enhance the cycling stability of P2-type cathodes. The high sodium content increases the sodium reservoir, reducing the depth of desodiation for a given capacity, while Li/Mg co-doping mitigates Na+/vacancy ordering and stabilizes the crystal structure. The optimized cathode exhibits significantly improved cycling performance, retaining 82.3% of its initial capacity after 500 cycles at 1C, compared to 65.4% for the undoped counterpart. Furthermore, the co-doped material demonstrates enhanced rate capability, delivering 112 mAh/g at 5C, and suppressed phase transitions, as evidenced by in-situ X-ray diffraction. This work provides a rational design pathway for high-performance P2-type cathodes, addressing key bottlenecks in SIB commercialization.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.