SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4362-y
The commercial viability of zinc-air batteries (ZABs) is constrained by the sluggish kinetics of the oxygen reduction reaction (ORR), which necessitates robust, cost-effective catalysts. While cobalt-based single-atom catalysts (Co SACs) exhibit superior selectivity and stability relative to Fe-N-C counterparts, their intrinsic ORR activity remains limited by scaling relations among intermediates. This study alleviates these constraints by precisely engineering the coordination symmetry of Co SACs. Through a mild annealing strategy, boron was incorporated into the first and second coordination shells of Co centers, creating an asymmetric Co-N3B-O local environment. The first-shell B/O coordination modulates the electronic structure of the Co center, while hydrogen bonding between *OOH and the coordinated O atom stabilizes the key intermediate, synergistically enhancing ORR activity. The optimized Co-BCN-950 catalyst delivers a peak power density of 216 mW cm-2 in ZABs, a 43% enhancement over commercial Pt/C (151 mW cm-2), alongside an open-circuit voltage of 1.43 V and a specific capacity of 790 mAh g-1. These findings establish a paradigm for tailoring the local coordination of SACs, enabling next-generation high-stability energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4452-8
Europium(III) complexes offer intrinsically narrow red emission (full-width at half-maximum < 5 nm) that is highly desirable for ultrahigh-definition displays, yet their electroluminescence performance is severely limited by unbalanced charge transport and inefficient energy transfer. This work reports a molecular design strategy that modulates both energy transfer and charge transport in Eu³⁺ OLEDs. The synthesized complex, Cz-Eu, incorporates a carbazole-functionalized ancillary ligand to facilitate host–guest energy transfer and hole transport. The single-crystal structure was deposited (CIF: Cz-Eu-cif.cif) and subjected to PLATON validation, which flagged 3 type-1 alerts (CIF construction/syntax errors), 8 type-2 alerts (possible structural model deficiencies), 12 type-3 alerts (low structure quality), and 4 type-4 alerts (improvement suggestions), with no duplication detected. These crystallographic alerts indicate that the reported structure requires further refinement before it can be considered reliable. Nevertheless, the device metrics demonstrate a promising route: the optimized OLED achieves efficient ultranarrow-band red emission, with the potential for high color purity and reduced power consumption. The findings underscore the critical role of ligand engineering in balancing charge fluxes and fostering efficient energy transfer, providing a viable pathway for next-generation red emitters. However, the structural ambiguities highlighted by the PLATON analysis warrant cautious interpretation of the structure–property relationships and suggest that additional crystallographic and device stability studies are necessary to substantiate the claimed performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4373-2
Infrared stealth technology demands materials with simultaneously low infrared emissivity and robust environmental stability. Traditional coatings suffer from high emissivity or poor thermal stability. Here, we report Sr-doped SmCoO3 perovskite ceramics achieving a record-low room-temperature infrared emissivity of 0.12 in the 8–14 μm atmospheric window. Systematic doping (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) via solid-phase synthesis reveals that Sr substitution induces a Co3+/Co4+ mixed valence state, increases oxygen vacancy concentration, and distorts the lattice. First-principles calculations (CASTEP) confirm that doping narrows the bandgap from 1.8 eV to 0.9 eV and enhances the double-exchange interaction, boosting carrier concentration and mobility. The optimized composition (x = 0.3) exhibits an electrical conductivity of 1.2×10^3 S/cm and a carrier density of 3.5×10^21 cm^-3, leading to strong infrared reflection. The material maintains emissivity below 0.15 after 100 hours of thermal cycling at 300°C and 500 hours of humidity exposure (85°C/85% RH), demonstrating exceptional environmental durability. This work establishes a new paradigm for designing high-performance inorganic infrared stealth materials via electronic-structural synergy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3860-0
Drug detection is critical for public health and security, yet reversible and highly sensitive sensing materials remain scarce. This study presents a novel ionogel sensor material, poly(ethylene glycol) diacrylate (PEGDA)/1-butyl-3-methylimidazole tetrafluoroborate, for reproducible detection of N-methylphenylethylamine (MPEA), a structural analogue of methamphetamine. The ionogel is fabricated by immobilizing a flowable ionic liquid within a PEGDA network via UV curing, preserving ionic mobility for efficient conduction. Integrated on a flexible poly(ethylene naphthalate) substrate, the sensor exhibits over 72.6% transmittance in the visible spectrum, enabling concealed attachment. Utilizing non-covalent interactions, the sensor achieves reproducible MPEA detection at sub-ppb levels at room temperature, with a theoretical detection limit of 317 ppt. It demonstrates high selectivity and consistency. Ionic conductivity was confirmed via current-voltage tests and impedance spectroscopy, and the sensing mechanism was clarified. The device maintains reliable performance under bending, indicating suitability for dynamic environments. With Bluetooth integration for wireless data transmission, the sensor shows strong potential for practical, discreet drug monitoring in real-world applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3657-9
Perovskite/silicon tandem solar cells (TSCs) have achieved power conversion efficiencies (PCE) up to 34.9%, surpassing the Shockley-Queisser limit of single-junction devices. The interconnection layer (ICL) critically bridges top and bottom subcells, enabling charge carrier recombination. Conventional indium oxide (In2O3)-based TCOs suffer from high-energy ion bombardment during sputtering, damaging amorphous silicon subcells and reducing open-circuit voltage (VOC) and fill factor (FF). Additionally, indium scarcity and cost necessitate indium-free alternatives. Here, we introduce a highly degenerate indium-free samarium-doped cadmium oxide (CdO:Sm) TCO as the ICL for perovskite/SHJ TSCs, deposited via low-damage reactive plasma deposition (RPD). The ultrathin CdO:Sm film (~3 nm) exhibits average transmittance of 85% (400–1200 nm) and 90% (800–1200 nm), enabling efficient near-infrared absorption in the bottom subcell. High doping concentration and mobility ensure excellent electrical conductivity. The low work function (4.04 eV) of CdO:Sm facilitates carrier tunneling and efficient recombination. Devices employing CdO:Sm ICL achieved approximately 1% higher efficiency compared to those with indium-based TCO ICLs. Detailed characterization including contact resistivity (1.68 mΩ cm2), conductive atomic force microscopy, Kelvin probe force microscopy, and photoluminescence quenching confirm enhanced carrier transport and extraction. This work demonstrates a viable indium-free ICL for high-efficiency perovskite/SHJ TSCs, addressing both performance and sustainability challenges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3927-9
The mechanical properties of as-cast TiAl alloys are severely limited by their coarse as-cast microstructure. This study proposes a low-temperature pre-deformation heat treatment to refine the microstructure of an as-cast Ti-47Al-2Nb-2Cr alloy. The process involves pre-deformation below the eutectoid temperature followed by heat treatment in the α+γ phase field, yielding two distinct microstructures: duplex (DP) and nearly lamellar (NL). The average lamellar colony size was reduced to 5.3% and 20% of the as-cast size for DP and NL structures, respectively. Microstructural evolution analysis reveals that the decomposition of coarse lamellar colonies and the formation of fine grains are governed by γ recrystallization, γ→α phase transformation, and α recrystallization. Remnant colonies after deformation are completely eliminated by subsequent heat treatment, enhancing microstructural homogeneity and mechanical properties. The DP alloy exhibits an ultimate tensile strength (UTS) of 537 MPa and an elongation (EI) of 6.8% at 800°C, representing increases of 44.7% and 518.2% over the as-cast alloy, respectively. Analysis of crack propagation and deformation mechanisms indicates that grain refinement and lamellar structure refinement contribute to improved deformation ability. This work provides a viable pathway for optimizing as-cast TiAl alloys for high-temperature applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3407-0
Grain boundary (GB) engineering has emerged as a promising strategy to enhance the near-room-temperature performance of Mg3(Sb,Bi)2-based thermoelectric materials, yet effective control of Mg distribution at GBs remains a significant challenge. Here, we report a novel approach to achieve targeted Mg segregation at GBs through strategic Ag incorporation in Mg3.3Sb0.5Bi1.497Te0.003. Through comprehensive microstructural characterization and first-principles calculations, we demonstrate that Ag preferentially segregates at GBs, forming Mg-rich MgAg alloy phases while maintaining limited solid solubility within the matrix. This unique GB architecture simultaneously optimizes multiple thermoelectric parameters: the Mg-rich GB regions significantly provide efficient carrier transport channels and enhance carrier mobility, while the MgAg phases and lattice disorders effectively scatter phonons without disrupting electron transport. Consequently, the optimized composition (x = 0.01) exhibits a remarkable enhancement in power factor at 300 K and maintains an average ZT of ~1.0 across 300–400 K. The material also demonstrates excellent mechanical properties and thermal stability, making it particularly suitable for near-room-temperature applications. Our findings not only establish an effective strategy for GB engineering in Mg3(Sb,Bi)2 systems but also provide valuable insights into the rational design of high-performance thermoelectric materials through interface modification.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61093-1
Advanced catalyst structures with good active site accessibility and strong metal-support interactions are crucial for oxygen reduction reaction (ORR) catalysis. A hierarchically porous Pt catalyst supported on honeycomb-like nitrogen-doped carbon (Pt/HNC-400, where 400 denotes the optimal dosage (mg) of the sacrificial SiO2 hard template used during synthesis) was fabricated by combining template-assisted pyrolysis and alcohol reduction. The fabrication involves the template-assisted pyrolysis of ZIF-67 (which provides the N-dopant through its 2-methylimidazole ligand) followed by HF etching to completely remove the SiO2, yielding a 3D interconnected porous carbon support. Compared to a commercial Pt/C, it had an exceptional ORR performance with a half-wave potential of 0.901 V (41 mV higher), a mass activity at 0.9 V that was 15.3 times higher, and significantly improved durability (a half-wave potential decay of 25 mV vs. 80 mV after 10,000 accelerated durability tests (ADTs)). Mechanistic investigations showed that this superior performance is due to the combined effects of the 3D porous structure, ultrafine Pt nanoparticles with strong metal-support interactions, and in-situ formed Co-Nx moieties from the pyrolysis of precursor ZIF-67. After 10,000 ADTs it was shown to have excellent structural integrity, retaining 87.4% of its initial electrochemically active surface area (102.7 m2 g−1). This study may assist the development of new high-performance ORR catalysts.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60640-8
Ethylene (C2H4) in vehicle exhaust is a highly reactive volatile organic compound (VOC) whose photo-oxidation with NOx contributes to the formation of O3 and secondary organic aerosols (SOA), a key precursor of PM2.5. This study designs a novel MgO-supported Ag-Cu bimetallic catalyst and investigates its performance using density functional theory (DFT). The effects of Ag and Cu loading on geometric structure, stability, and reactant adsorption are analyzed, and the catalytic oxidation pathways of C2H4 over AgCu-MgO are elucidated. Results indicate that loading Ag significantly enhances C2H4 adsorption, with a maximum adsorption energy of -1.46 eV, while O2 adsorption remains weak (-0.45 eV). Cu-MgO shows moderate C2H4 adsorption (-0.87 eV at bridge site) but higher O2 adsorption (-0.76 eV). Among 17 AgCu-MgO dual-atom catalyst (DAC) configurations, those with Ag and Cu co-adsorbed at Mg sites are thermodynamically more stable (binding energies below -10 eV). Configurations with Ag and Cu in close proximity enhance co-adsorption of C2H4 and O2. C2H4 oxidation preferentially proceeds via C=C bond cleavage to form *CH3 and CO2. For three representative configurations (1, 3, 6), free energy barriers for rate-limiting steps in the *HCO and CH2O pathway are consistently higher than those for *CH3 and CO2 pathway. Configuration 6 exhibits the lowest energy barrier (0.32 eV) for its rate-limiting step, indicating the highest catalytic performance. This study provides atomic-scale insights for rational design of efficient catalysts targeting olefinic pollutants in automotive emissions.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605001
The lower reaches of the Yangtze River Basin, as a concentrated area of China's C5 petroleum resin industry, face critical bottlenecks in green and low-carbon transformation due to high-pollution, refractory wastewater and high carbon emissions. Traditional petrochemical wastewater treatment technologies suffer from low efficiency, high energy consumption, and insufficient resource utilization. This paper systematically analyzes the sources of wastewater in C5 petroleum resin production from principles and processes, and reviews research progress and carbon reduction potential of current technologies in three aspects: new materials, new equipment, and new processes. Integrated processes centered on efficient pretreatment, biological enhancement, and multi-technology coupling show significant advantages in improving treatment efficiency, reducing energy consumption and cost, and strengthening resource recovery. The study also prospects future research priorities for pollution and carbon mitigation through green technological innovation and intelligent upgrading, providing new solutions for 'near-zero discharge' and resource recycling of C5 petroleum resin wastewater, thereby promoting the green and low-carbon transformation of the petrochemical industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3850-3
Chiral nanomaterials have attracted considerable attention for antibacterial applications due to their unique chiroptical properties. Here, we report a novel spatiotemporally precise synergistic photodynamic therapy (PDT) and photothermal therapy (PTT) strategy using circularly polarized light (CPL)-activated chiral molybdenum-doped carbon dots (L-Mo-CDs and D-Mo-CDs). These chiral carbon dots were synthesized using chiral tartaric acid as a precursor. Notably, D-Mo-CDs selectively respond to left-handed CPL (LCP), while L-Mo-CDs respond to right-handed CPL (RCP). Under CPL irradiation, D-Mo-CDs exhibit enhanced reactive oxygen species (ROS) generation and a higher photothermal conversion efficiency (PCE) compared to L-Mo-CDs. In vitro antibacterial assays demonstrate that D-Mo-CDs possess excellent bactericidal efficacy against both Gram-positive and Gram-negative bacteria. In vivo wound healing studies in a mouse model reveal remarkable therapeutic efficacy, attributed to reduced inflammation, accelerated angiogenesis, and enhanced collagen deposition. This work introduces a paradigm for utilizing chiral carbon dots in precision antibacterial therapy, addressing the limitations of conventional chiral nanomaterials such as poor biocompatibility and low photothermal conversion. The findings underscore the potential of metal-doped chiral carbon dots for advanced biomedical applications, offering a spatiotemporally controllable approach to combat bacterial infections without promoting resistance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3750-6
SnSe is a promising thermoelectric material for medium-temperature applications due to its ultralow lattice thermal conductivity. However, the poor electrical conductivity of n-type polycrystalline SnSe significantly hinders its practical application. Here, we propose a dual-functional strategy employing InBr3 doping to synergistically enhance electrical transport while suppressing lattice thermal conductivity. For the first time, we demonstrate the successful construction of a Br-enriched conductive network within the SnSe matrix. The incorporation of In3+ and Br− introduces high-density charge carriers, while Br forms percolative conductive networks, resulting in a remarkable enhancement of carrier mobility to ~20.64 cm2 V−1 s−1. Simultaneously, the lattice thermal conductivity is substantially reduced to ~0.25 W m−1 K−1 through the formation of multi-scale defects, including dislocations and Br-rich nanowires, which effectively enhance phonon scattering. As a result, we achieve a peak figure of merit of ZT ~1.41 at 823 K, with an average figure of merit of ~0.42 over the temperature range of 323–823 K. This work provides a universal paradigm for decoupling electron-phonon interactions in thermoelectric materials, offering new insights for the optimization of thermoelectric performance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025120801
The interaction between microplastic-derived dissolved organic matter (PSDOM) and iron oxides in soil environments can modulate its photosensitization effects, yet the underlying mechanisms remain elusive. This study investigated the influence of hematite with distinct morphologies—flake-shaped (HNPs) and cubic (HNCs)—on the photosensitization of polystyrene-derived dissolved organic matter (PSDOM). Under 500 W mercury lamp irradiation, both hematite morphologies promoted PSDOM degradation, with HNCs exhibiting superior performance: total organic carbon (TOC) decreased from 18.4 mg·L−1 to 12.3 mg·L−1 within 90 min, compared to 13.3 mg·L−1 for HNPs. Three-dimensional fluorescence spectroscopy indicated that hematite alters the humification process, thereby modifying photosensitization. Electron paramagnetic resonance (EPR) spectroscopy identified the generation of singlet oxygen (1O2), hydroxyl radicals (·OH), and carbon-centered radicals (CH3C(=O)OO·). HNCs significantly enhanced 1O2 production, while HNPs favored ·OH generation; both inhibited CH3C(=O)OO· formation. Quantitative analysis via high-performance liquid chromatography revealed that the steady-state concentration of 1O2 was highest with HNCs, reaching 2.80 times that of the PSDOM control, whereas ·OH concentration peaked with HNPs at 1.98 times the control. Notably, the steady-state concentration of 1O2 was approximately three orders of magnitude higher than that of ·OH. These findings elucidate the morphology-dependent role of hematite in PSDOM photosensitization, providing mechanistic insights into the environmental fate of microplastic-derived organic matter in complex soil systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4140-9
Metal covalent organic frameworks (MCOFs) are promising photocatalysts for carbon dioxide reduction reaction (CO2RR). However, the synthesis of ketimine-linked COFs remains challenging due to the low reactivity of ketones. Here, we report a straightforward strategy to construct diketimine-linked MCOFs via the condensation of acenaphthenequinone (Ace) with 1,3,6,8-tetra(4-aminophenyl)pyrene (TAPPy). The metal-free COF (TACOF-AA) exhibits AA stacking, while the addition of NiCl2·6H2O under identical conditions yields an AB-stacked Ni-based MCOF (Ni-TACOF-AB). The coordinated Ni species serve as active sites for CO2RR and enhance electron-hole separation. Photocatalytic tests demonstrate that Ni-TACOF-AB achieves a CO evolution rate of 11.71 mmol g−1 h−1 with 99.9% selectivity, which is 7.6 times higher than that of TACOF-AA. Density functional theory (DFT) calculations reveal that Ni-TACOF-AB lowers the activation energy barrier of the rate-determining step by regulating local charge distribution, facilitating electron transfer to adsorbed CO2. This work provides a novel approach for synthesizing ketimine-based COFs and highlights the importance of interlayer stacking in modulating photocatalytic performance.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202503016
Open-pit coal mining severely damages soil and plant community structure and function, causing soil nutrient loss and ecological degradation. Vegetation reconstruction is a key measure for restoring degraded mining ecosystems, with the core challenge being the selection of suitable plant species and optimization of plant configurations. This study focused on the degraded ecosystem of the Baiyinhua open-pit mine in Inner Mongolia, screening native plant species for vegetation reconstruction experiments to investigate early-stage changes in soil nutrient availability and the underlying microbial mechanisms. Results showed that soil physicochemical properties and fungal community diversity exhibited strong adaptability during early reconstruction. However, soil fungal community composition and the relative abundance of saprotrophic fungi differed significantly among plant configurations. Leymus chinensis significantly increased the proportion of soil saprotrophic fungi from 67.28% in the control to 81.63%, while reducing the relative proportion of pathogenic fungi from 15.63% to 4.33%, demonstrating its potential to enhance soil health. Medicago rivularis improved soil microbial community composition and increased soil available phosphorus content, highlighting its capacity as an excellent pioneer species for optimizing soil nutrient availability. Furthermore, mixed sowing of grasses and legumes showed potential to enhance the nitrogen-fixing effect of legumes. Given the significant positive correlation between soil fungal community composition and total nitrogen and available nitrogen, the effects of different plant configurations on soil nutrient availability and biological health likely stem largely from the regulation of soil fungal community composition. In conclusion, achieving the goal of selecting optimal plant configurations still requires long-term continuous observation and analysis, particularly for optimizing configurations between high-quality grasses like Leymus chinensis and legumes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511041
Hydroxyl radicals (·OH) generated via dark reactions under fluctuating redox conditions significantly influence pollutant degradation and elemental cycling, yet the key electron supply mechanisms driving their sustained production remain unclear. This study aimed to elucidate the electron-driven processes underlying sustained dark ·OH generation in mangrove soils under redox fluctuations. Simulated tidal redox cycles were conducted, and electron donating capacity (EDC), three-dimensional fluorescence spectroscopy, nuclear magnetic resonance, and high-throughput sequencing were employed to analyze the dynamics of different Fe(II) species, key organic matter components, and microbial communities. Results demonstrated that, without exogenous electron donors, mangrove soils exhibited stable ·OH generation potential and EDC. During early redox cycles, total EDC of soil suspensions was dominated by reactive Fe(II), while the contribution of reduced organic matter increased over time, with solid-phase components accounting for 94.5%–97.6% of total EDC. Humic acids in soil organic matter facilitated reversible electron transfer via quinone functional groups, maintaining redox activity. Geothermobacter and Desulfobulbus were identified as dominant iron-reducing bacteria, likely key microorganisms for regenerating the "iron-organic matter" electron sources. This study reveals the mechanisms of endogenous electron donor regeneration and sustained dark ·OH generation mediated by iron and organic matter cycling in mangrove soils, providing theoretical support for understanding the long-term environmental effects of ·OH in tidal environments and its impact on biogeochemical cycles.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512052
Constructed wetlands (CWs) with conventional substrates often exhibit limited removal of nitrogen and antibiotics from secondary effluent. This study developed an iron-carbon-manganese ore (Fe-C-Mn) composite substrate CW to enhance simultaneous removal of nitrogen and tetracycline (TC). Under influent TC of 2 mg·L−1 and total nitrogen (TN) of 15 mg·L−1, the Fe-C-Mn system achieved average TC removal of 91.3%, significantly higher than the gravel control (27.2%). TN and nitrate nitrogen (NO3−-N) removals reached 71.7% and 83.3%, respectively, versus 7.8% and 1.2% in the control. Substrate analysis revealed increased surface roughness and synergistic generation of active components (Fe(II)/Fe(III) and Mn(II)), driving autotrophic denitrification and TC biodegradation/chemical degradation. Microbial community analysis indicated reduced overall diversity but selective enrichment of potential TC degraders (e.g., Trichosporon, Bacillota) and denitrifiers (e.g., unclassified_f_Rhodocyclaceae). TC degradation pathways included demethylation, hydroxylation, and ring-opening, ultimately yielding small metabolites. These findings provide theoretical and technical support for enhanced removal of antibiotics and nitrogen from secondary effluent using CWs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3951-4
Silicon anodes offer an ultrahigh theoretical capacity (4200 mAh g−1) but suffer from >300% volumetric expansion during cycling and unstable solid electrolyte interphase (SEI) formation, leading to rapid capacity fading. Here, we design a hierarchical composite p-cSi@aSi@MgSiN2@C featuring a porous crystalline-amorphous silicon core (p-cSi@aSi), an in-situ MgSiN2 transition layer, and an outer nitrogen-doped carbon shell. The 3D interconnected pores accommodate volume expansion, while amorphous silicon enables isotropic lithiation-induced strain, eliminating crystalline phase transition barriers. The MgSiN2 layer transforms into a tough Li3N-rich SEI with ultra-fast ion channels, and the carbon shell provides mechanical confinement and electronic conductivity. This synergistic interface engineering achieves an initial coulombic efficiency (ICE) of 81.4%, a charge transfer resistance of 16.4 Ω after 200 cycles (64% reduction), and a Li+ diffusion coefficient of 1.72×10−11 cm2 s−1. The anode delivers 1719.3 mAh g−1 at 0.2 C after 200 cycles and 823.8 mAh g−1 at 0.5 C after 500 cycles. The molten salt electrolysis synthesis achieves a current efficiency of 68.12% and specific energy consumption of 12.76 kWh kg−1, with an estimated electricity cost of 1154.69 USD ton−1, only 20% of commercial Si/C anodes. This work resolves the ICE-cycle life trade-off and provides a scalable, cost-effective approach for next-generation high-energy batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4030-y
In the era of artificial intelligence, efficient perception and processing of massive visual information demand advanced machine vision systems. Inspired by human visual adaptation, various optoelectronic devices have been developed, yet most rely on external gate voltages or complex circuits for dynamic sensitivity modulation. This work demonstrates an all-optically controlled biomimetic sensor based on a one-dimensional ZnO/MAPbBr3 heterojunction, achieving both positive and negative photoconductivity effects. By modulating oxygen vacancy states with ultraviolet light, the competition between intrinsic photoconduction and trap-mediated carrier capture is regulated, enabling dynamic control of visible-light photoresponse within a single device. This tunable behavior mimics scotopic adaptation (photopigment regeneration under weak illumination), photopic adaptation (photopigment bleaching in bright environments), and eyelid-like self-protection against intense light. The device operates without external gate bias or cascaded circuits, offering a promising strategy for next-generation intelligent biomimetic sensors in machine vision.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4019-1
Vision is a vital means for humans to perceive the environment, with 80% of information from visual perception. Developing visual systems approaching or surpassing human-level vision plays an indispensable role in advancing autonomous driving, intelligent security, and other fields. Optoelectronic neuromorphic devices, integrating sensing and memory, are promising for emulating human vision. This study constructs a biomimetic visual system based on a 16 × 16 InAlZnO optoelectronic neuromorphic array with oxygen vacancy gradients. Under multi-factor modulation (oxygen vacancy concentration differences, Ag ions, heterojunction interfaces), the device achieves electrical/optical conductance tunability. Integrated with external circuits and a field-programmable gate array, the system successfully emulates human vision capabilities: image memory, denoising, attention mechanism, and motion state perception (direction, speed, color). Image digit recognition based on visual attention reaches 97.15% accuracy, and motion state recognition reaches 100%. This system will promote bionic vision development and application, paving the way for high-performance neuromorphic vision systems surpassing the human eye.