SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4439-4
Silk fibroin (SF) hydrogels are promising for neural regeneration but suffer from progressive stiffening due to excessive β-sheet assembly, limiting their use in traumatic brain injury (TBI) repair. This study introduces a dopamine (DA)-mediated synergistic topological entanglement strategy to construct an SF-DA/gelatin-DA composite hydrogel (SG). The system integrates covalent cross-linking, net cationic electrostatic repulsion, hydrogen bonding, and π-π stacking to regulate SF assembly dynamics at the molecular level. The resulting SG hydrogel maintains stable mechanical softness over extended periods, with a storage modulus of approximately 1.2 kPa after 28 days, compared to a 5-fold increase in pure SF hydrogels. The sustained softness promotes neural stem cell (NSC) proliferation and differentiation, with a 2.5-fold increase in βIII-tubulin expression and a 1.8-fold increase in GFAP expression after 14 days. In a rat TBI model, SG hydrogel implantation reduced glial scar formation by 40% and improved neurological function scores by 30% at 8 weeks. The hydrogel degrades at a rate of 12% per week, matching tissue regeneration. This multi-crosslinking approach offers a clinically translatable strategy for neural tissue engineering, addressing the critical bottleneck of mechanical instability in SF-based biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3684-4
The efficient conversion of dinitrogen (N2) to ammonia (NH3) under mild conditions remains a critical challenge for sustainable nitrogen fixation. This study reports a rationally designed ternary heterojunction, GO/MXene/UiO-66 (GM/UiO-66), which achieves directed charge transfer for enhanced photocatalytic nitrogen fixation. The internal electric field at the heterointerface drives anisotropic migration of photogenerated charges, leading to rapid separation of electron–hole pairs and suppression of interfacial recombination. The intrinsic defect structure of graphene oxide (GO) provides active sites for N2 adsorption and activation, while π–π interactions between GO and UiO-66 accelerate electron transfer. Additionally, the Schottky junction between UiO-66 and MXene facilitates hole (h+) transfer. The incorporation of GO and MXene extends visible-light absorption of UiO-66. Under simulated solar illumination, GM/UiO-66 exhibits an NH3 generation rate of 25.1 μmol g−1 h−1, which is 1.9 times higher than that of pristine UiO-66 (13.5 μmol g−1 h−1). This work presents a novel strategy for designing ternary heterojunction composites that optimize charge transfer and significantly improve photocatalytic performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3729-9
Polymer capacitors are essential for modern power electronics, but their operation is limited by poor energy density at elevated temperatures. Biaxially oriented polypropylene (BOPP), the industry standard, fails above ~105 °C. This highlight discusses a breakthrough by Yang et al. that uses a generative machine-learning pipeline to discover organic fillers with both wide bandgap (Eg) and high electron affinity (Ea), properties typically mutually exclusive. The model screened over fifty thousand structures to identify more than two hundred high-scoring candidates. Two representatives, 4,6-dinitrobenzene-1,3-dicarbonitrile and 2,4,6-tricyano-1,3,5-triazine, were synthesized, exhibiting Eg ≈ 5.5 eV and Ea ≈ 4.5 eV. Dispersed in a polyimide host, these fillers create deep electron traps that suppress leakage current and delay avalanche breakdown. Composite films achieved an energy density of 5.1 J cm−3 at 250 °C with 90% efficiency, outperforming conventional polymers. The team scaled production using a roll-to-roll line, producing kilometer-scale films with uniform dispersion. This work demonstrates a viable path to high-temperature polymer capacitors for traction inverters and DC-link applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0034
Catalytic cracking of gasoline and diesel to light olefins is a pivotal route for high-value utilization of surplus fuels, typically employing zeolite catalysts. This study systematically investigates the effects of zeolite type and acidic properties on the catalytic cracking of dodecane, a diesel model compound, using SAPO-34, ZSM-5 with SiO2/Al2O3 ratios of 38, 85, and 200, and USY. Catalysts were characterized by XRD, SEM, N2 physisorption, NH3-TPD, and pyridine-FTIR, and evaluated in a fixed-bed reactor. Results demonstrate that zeolite type is the primary determinant of conversion and product distribution. SAPO-34, with 0.38 nm pores, achieved only 24.33% conversion and negligible BTX yield, with severe external coking. ZSM-5-38 and USY, with larger pores, achieved near-complete conversion; however, ZSM-5-38, possessing moderate acidity, yielded the highest light olefins (18.40%) and minimal coke (0.18%), while USY, with higher acidity, promoted hydrogen transfer and coking (12.90% coke). Within ZSM-5 series, lower acid site density (ZSM-5-200) proved optimal, achieving 97.79% conversion and a total light olefin yield of 41.93% (ethylene 11.11%, propylene 20.33%, butenes 10.49%) with low coke (0.43%). The study proposes reaction pathways and regulatory mechanisms, highlighting that zeolite type and acidity govern the relative rates of cracking, hydrogen transfer, oligomerization, aromatization, and coking, thereby dictating performance. These findings provide a rational basis for optimizing zeolite catalysts in commercial gasoline/diesel cracking processes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026012501
Childhood hypertension is a growing global concern, with approximately 4% of Chinese children exhibiting sustained elevated blood pressure meeting hypertension criteria, and single-time-point screening detecting rates of 14%–20% (up to 19% in obese children). Environmental exposure to metals (lead, cadmium, arsenic, mercury, copper, chromium) and bisphenol analogues (bisphenol A, S, F) has been implicated as a modifiable risk factor. This review synthesizes epidemiological evidence linking such exposures to blood pressure alterations in children and adolescents, highlighting dose-response relationships and potential mechanisms, including oxidative stress, endothelial dysfunction, and epigenetic programming. Key findings from cited studies indicate that low-dose bisphenol A exposure alters human cardiomyocyte functionality, and synergistic effects with insulin resistance elevate childhood blood pressure. Metal exposures, particularly lead and cadmium, are associated with increased blood pressure and cardiovascular structural changes. The review underscores the critical window of developmental exposure and the 'tracking phenomenon' linking childhood blood pressure to adult hypertension. Limitations include cross-sectional designs and confounding by mixed exposures. Future research should employ longitudinal cohorts and multi-pollutant models to refine risk assessment. Preventive strategies should integrate school health programs to reduce environmental exposure and monitor cardiovascular health.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512045
To optimize the anode structure of Ti/SnO2-based electrodes in electrochemical advanced oxidation processes (EAOPs) and enhance their electrocatalytic activity and stability, Sn-Sb co-doped Ti/SnO2 electrodes were fabricated via a sol-gel method. The degradation performance and mechanism were evaluated using phenol as a model pollutant. Three electrodes were prepared with different Sn/Sb molar ratios: Ti/SnO2 (10:0), Ti/Sb (0:10), and Ti/SnO2-Sb (9:1). Characterization by XRD, SEM, and electrochemical tests revealed that the Sn-Sb co-doped electrode exhibited a dense surface, higher oxygen evolution potential (OEP), larger electrochemically active surface area, and lower charge transfer resistance compared to single-doped counterparts. In constant-current electrolysis experiments (20 mA·cm−2, pH=5, 0.1 mol·L−1 Na2SO4), the co-doped electrode achieved superior phenol and TOC removal efficiencies and higher apparent rate constants, with the lowest specific energy consumption per unit TOC removal. Radical quenching and intermediate analysis indicated that hydroxyl radicals (·OH) were the dominant reactive species. The degradation pathway involved aromatic ring hydroxylation, ring opening, and further mineralization of short-chain carboxylic acids. Sn-Sb co-doping enhanced the generation of ·OH by increasing surface adsorbed oxygen and defect site density. This synergistic doping strategy significantly improved the electrocatalytic activity and service life of Ti/SnO2-based anodes, providing a basis for the rational design of anode materials for EAOPs in treating refractory organic wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511062
Sediment microbial fuel cells (SMFCs) are a green technology for simultaneous polluted sediment remediation and energy recovery, yet their performance is constrained by insufficient anodic microbial activity and low electron transfer efficiency. This study employed lactate addition combined with composite engineered microbial immobilization to synergistically optimize SMFC performance by enhancing microbial stability and carbon source supply. Results showed that lactate, as an easily utilized electron donor, promoted electrochemical activity, achieving a maximum power density of 22.06 mW·m−2 at 6 mmol·L−1, a 194% improvement over the blank group. Immobilization further enhanced electron transfer efficiency, with the highest output voltage (88.75 mV) being 2.09 times that of the non-immobilized group. For pollutant degradation, the 6 mmol·L−1 lactate group achieved TOC and TN removal rates of 29.02% and 28.4%, respectively, outperforming the control (22.41% and 21.42%). However, high lactate concentrations inhibited microbial metabolism, leading to TOC accumulation. 16S rRNA analysis revealed that the anodic microbial community was dominated by Bacillota and Pseudomonadota, both possessing electroactive and pollutant-degrading capabilities, indicating that lactate and immobilization exert a synergistic effect in SMFCs, simultaneously enhancing electricity generation and pollutant removal efficiency.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042502
Rice husk biochar (BC) was modified with boron (B) and nitrogen (N) doping and loaded with Fe3S4 to fabricate B-BC@Fe3S4 and N-BC@Fe3S4 catalysts for peroxydisulfate (PDS) activation and enrofloxacin (ENR) degradation. Characterization via SEM, BET, XRD, Raman, and XPS confirmed successful heteroatom incorporation and uniform Fe3S4 dispersion, enhancing specific surface area and defect sites. Degradation experiments showed that B-BC@Fe3S4 and N-BC@Fe3S4 achieved ENR removal efficiencies of 90.72% and 91.89%, respectively, significantly outperforming unmodified BC@Fe3S4 (82.21%). Mechanistic studies revealed that PDS activation proceeded via Fe3S4-mediated electron transfer generating radical species (SO4•−, •OH, O2•−) and via B/N functional groups promoting non-radical singlet oxygen (1O2) formation. Notably, N-BC@Fe3S4 exhibited superior resistance to Fe3+ leaching and greater environmental adaptability under varying pH, anion, and humic acid conditions. These findings demonstrate that B/N-doped biochar-supported Fe3S4 are effective catalysts for PDS activation, offering promising potential for antibiotic removal from real wastewater matrices.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022702
This study systematically investigated the occurrence and vertical distribution of per- and polyfluoroalkyl substances (PFAS) in solid waste, leachate, and surrounding groundwater at a municipal solid waste landfill in Fuyang City, Anhui Province, China. A total of 23 PFAS were detected in solid waste, with total concentrations (∑PFAS) ranging from 7.95 to 172.28 ng·g⁻¹. Trifluoroacetic acid (TFA), an ultrashort-chain PFAS, was ubiquitous, contributing on average 59% to the total PFAS mass. PFAS composition varied with depth: long-chain PFAS dominated in middle and upper layers, while short-chain and ultrashort-chain PFAS were more abundant in deeper layers, indicating enhanced downward migration of shorter-chain compounds. Sulfonic acid PFAS exhibited increasing relative abundance with depth. Leachate ∑PFAS concentration was 14.35 μg·L⁻¹, dominated by short-chain compounds such as PFPrS and PFBS, consistent with the composition in bottom-layer waste. Groundwater surrounding the landfill contained multiple PFAS, with concentrations decreasing with distance from the landfill, confirming the landfill as a source of PFAS to the surrounding environment. Multivariate analyses (PCoA and Bray–Curtis dissimilarity) revealed that some groundwater samples closely resembled leachate in PFAS composition, suggesting direct impact via leachate migration. These findings underscore the role of landfills as significant reservoirs and sources of PFAS, particularly ultrashort-chain compounds, and highlight the need for improved leachate management to mitigate groundwater contamination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4017-y
Lattice distortion via entropy engineering can significantly optimize thermoelectric performance by intensifying phonon scattering. However, excessive lattice distortion in high-entropy materials inevitably hinders carrier transport, limiting the wide-temperature average ZT (ZTave). To enhance the wide-temperature thermoelectric performance of low-cost PbS-based compounds, this work introduces moderate lattice distortion by controlling entropy around 1.0R (R is the gas constant) to balance phonon and carrier transport, alleviating restrictions on carrier mobility. Substantial Se and Te alloying in PbS induces rock-salt lattice distortion, effectively impeding phonon propagation, thus suppressing lattice thermal conductivity (κlat) from 2.41 W m−1 K−1 in PbS to 0.66 W m−1 K−1 in PbS0.5Se0.35Te0.15 at 300 K. Additionally, Cu interstitials are introduced into the lattice-distorted PbS0.5Se0.35Te0.15 to further optimize carrier density and weighted carrier mobility (μW), leading to significant improvement in μW/κlat parameter at 300–773 K. Finally, a room-temperature ZT of 0.53 and a maximum ZT of 1.44 are obtained in PbS0.5Se0.35Te0.15-1%Cu sample, contributing to an impressive ZTave of 1.08 at 300–773 K and a maximum power generation efficiency (ηmax) of 7.5%. The results outperform previously reported cost-effective PbS-based compounds and highlight the importance of lattice distortion regulation in enhancing wide-temperature thermoelectric performance.