SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0001
The escalating global demand for carbon reduction has positioned chemical absorption using alkanolamine solvents as the predominant post-combustion CO2 capture technology, owing to its high absorption efficiency and process maturity. However, the regeneration of CO2-rich solvents is energy-intensive, with the desorption step accounting for 40.0%–60.0% of total energy consumption. Traditional amine-based methods suffer from high energy penalties, solvent degradation, and equipment corrosion, limiting scalability. Catalytic CO2 desorption, employing solid acid catalysts (SACs), has emerged to address these challenges by lowering the activation energy for CO2 release, enhancing reaction kinetics, and enabling efficient regeneration at lower temperatures (110–130 °C reduced). This review systematically examines research from the past five years on key catalyst materials, focusing on structure-activity relationships, synergistic mechanisms of Lewis acid, Brønsted acid, and basic sites, and their influence on desorption pathways. It highlights that SACs not only improve desorption dynamics but also facilitate catalyst recovery, avoiding adverse effects on absorption. The paper analyzes current scientific and technological challenges, including catalyst stability, selectivity, and scale-up, and provides an outlook on industrial application in low-cost carbon capture. Key findings indicate that catalysts such as metal-organic frameworks (MOFs), heteropolyacids, and waste-derived materials can reduce regeneration energy by up to 30%–40% while maintaining high desorption efficiency. The review underscores the potential of catalytic regeneration to significantly lower operational costs and enhance the viability of amine-based CO2 capture in industrial settings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.