SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4294-4
Room-temperature phosphorescence (RTP) polymer materials are attractive for flexible electronics and information encryption due to their tunability and processability. However, achieving polymeric RTP systems that simultaneously exhibit high thermal sensitivity, reversible multicolor emission, and long phosphorescence lifetime (τPhos) with high quantum yield (ΦPhos) remains challenging. Here, we report an in-situ cross-linked self-assembly strategy that converts flexible polymers into rigid polymer microspheres, yielding long τPhos, high ΦPhos, and thermally and time-dependent tunable RTP. The resulting microspheres (PM0.1-0.01-1) exhibit a maximum τPhos of 1754 ms and ΦPhos of 42.83%, markedly superior to previously reported intrinsic polymer RTP materials. At 77 K, they display ultralong green emission with a lifetime of 6019 ms and visible afterglow lasting up to 99 s. The cross-linked microspheres enable time-dependent, continuously tunable RTP and thermally responsive color switching, while maintaining excellent phosphorescence stability in aqueous and high-temperature environments. This provides a versatile platform for dynamic information encryption, full-color afterglow LEDs, and temperature sensing. The strategy establishes a general design principle for developing multidimensional, controllable, and stable high-performance polymer RTP materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3649-0
Injectable hydrogels formed via dynamic chemical crosslinks hold great promise as drug delivery platforms due to their robust yet adaptable nature, stimuli-responsiveness, and tunable structures and properties. However, their inherently high water content poses a significant challenge for the efficient encapsulation and sustained release of hydrophobic drugs. Here, we present a novel injectable hydrogel system constructed via a strain-promoted disulfide-thiol exchange between dithiolane-functionalized polymer strands and thiolated core-shell nanoparticles (NPs) under physiological conditions. The hydrophobic core and hydrophilic shell structure of the NPs enables effective loading and protection of hydrophobic drugs, while rapid gelation occurs upon mixing the thiolated NPs with dithiolane-polymers in phosphate-buffered saline. The hydrogel shows excellent injectability, self-healing capability, in vitro biodegradability, and cytocompatibility. This hydrogel system enables sustained release of hydrophobic drugs over 32 days in aqueous media and supports sequential dual-drug release. Its redox-responsiveness under tumor-mimicking reducing conditions, enabled by the disulfide crosslinks, further facilitates controlled intracellular drug release. This multi-component platform offers a versatile strategy for designing advanced injectable hydrogels with potential applications in hydrophobic drug delivery and other biomedical fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3654-5
Hydrogen production by photosynthetic green algae is an efficient biological process that utilizes light energy to convert water and carbon dioxide into clean and renewable energy. In this paper, we constructed a hybrid system combining graphitic carbon nitride (g-C3N4) and Chlorella pyrenoidosa (Chlorella), in which g-C3N4 serves as an extracellular electron source and Chlorella acts as a biological reactor for specific hydrogen production. In particular, the electronic structure of carbon nitride was optimized by means of hydrothermal alkalization and copper ion doping, expanded the light absorption range and enhanced the light response ability. g-C3N4, as an extracellular electron source, can provide electrons for Chlorella to improve hydrogen production performance which is 3.7 times that of bare Chlorella. The construction of a biological hybrid system is a feasible optimization strategy for the hybrid system to promote the synergistic effect of the hybrid system by regulating the properties of non-living components.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3887-6
The proliferation of 5G/6G communications and radar systems has intensified electromagnetic wave (EMW) leakage, interference, and thermal management challenges. This study presents a 3D MXene sponge/NiFe@NC heterostructure with tunable pore architecture, fabricated by pyrolyzing a polyurethane (PU) foam template uniformly coated with NiFe-decorated Ti3C2Tx MXene nanosheets. The resulting porous dielectric-magnetic network integrates interconnected MXene pathways with uniformly dispersed NiFe@NC nanoparticles, enabling synergistic dielectric-magnetic loss via conduction loss, dipole/interface polarization, and magnetic loss. Precise pore structure design enhances impedance matching and promotes multi-scattering and internal reflection of EMWs. An 'EMW-pore matching' mechanism is proposed, where pore size governs impedance matching at specific frequencies, enabling tunable absorption performance. The optimized absorber achieves a reflection loss (RL) of -67.84 dB, while radar cross-section (RCS) simulations confirm exceptional attenuation and stealth potential. Additionally, the 3D skeleton derived from PU foam confers remarkable thermal resistance and flame retardancy. This pore-regulation strategy provides a scalable route to designing lightweight, broadband, and thermally stable EMW absorbers for next-generation communication and stealth applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3609-0
This correction addresses an inadvertent duplication error in Fig. 4d of the original article published in Sci China Mater 2021, 64(8): 2045–2055. The TUNEL staining image of tumor tissue in the PBS group was mistakenly duplicated with the Vector/siNC group during figure assembly. The corrected Fig. 4 is provided, which includes the timeline for in vivo tumor immunotherapy, relative tumor volume changes (n=6 per group; **p<0.01, ***p<0.001), relative mouse body weight variations, and H&E and TUNEL staining of tumor sections on day 14. The correction does not alter the overall results, interpretation, or conclusions of the study. The original research demonstrated that dendrimer-entrapped gold nanoparticles (Au DENPs) can effectively deliver siRNA for gene silencing, thereby boosting immune checkpoint blockade for tumor therapy. The study highlighted the potential of this nanoplatform for combined gene therapy and immunotherapy in cancer treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021602
Iron-based catalysts are widely used in water pollution treatment due to their high stability and redox capabilities. However, conventional single-component iron-based catalytic systems face challenges such as slow reaction kinetics and low efficiency in generating reactive oxygen species (ROS) during organic pollutant degradation. In this study, three electroactive bacteria (Bacillus megaterium, Lactococcus lactis, and Shewanella putrefaciens) were selected to interact with nano-Fe3O4 to construct bacterial/Fe3O4 hybrid materials, accelerating the degradation of gallic acid. The results showed that bacterial interaction with Fe3O4 facilitated rapid electron transfer, enhancing gallic acid degradation. The bacterial/Fe3O4 hybrid materials exhibited significantly higher gallic acid degradation rates compared to Fe3O4 alone. This improvement was mainly attributed to the ability of electroactive bacteria to promote the formation of oxygen vacancies (OVs) on the Fe3O4 surface, accelerating electron transfer and subsequently enhancing the generation of ROS, including hydroxyl radicals, superoxide radicals, and singlet oxygen. Correlation analysis demonstrated a significant positive relationship between OVs and ROS generation, with hydroxyl radicals showing the highest correlation with the gallic acid degradation rate constant (r = 0.98), indicating its dominant role in gallic acid degradation; the hydroxyl radicals quenching experiment also verified its dominant role. Additionally, due to the temperature sensitivity of bacteria, the degradation rate of gallic acid reached its peak in the temperature range of 30–40 °C. This study reveals the mechanism by which electroactive bacteria enhance the catalytic activity of Fe3O4, providing a new strategy for its application in advanced oxidation technology for water pollution treatment.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60670-6
Direct conversion of syngas to higher alcohols (C2+ alcohols) is critical for coal-based resource utilization and energy security. Here, a series of Na-modified CoFe/Al2O3 catalysts were synthesized via incipient wetness impregnation and evaluated for syngas-to-alcohol reactions. Multiple characterizations (XRD, N2 adsorption-desorption, H2-TPR, XPS, DRIFTS, in situ Raman, Mössbauer spectroscopy) elucidated synergistic effects of Na and Fe promoters. Na facilitated formation of Co-Fe alloy sites during reaction, while Fe modified electronic state of Co and promoted transformation of lattice oxygen to adsorbed oxygen, increasing surface oxygen vacancies. Synergistic interaction between alloy and carbide sites enhanced CO insertion into olefin intermediates, improving C2+ alcohol selectivity. Under 260 °C and 2 MPa, Co1Fe1Na1 catalyst (n(Co):n(Fe):n(Na)=1:1:1) achieved total alcohol selectivity of 45%, with C2+ alcohols comprising 94.1% of total alcohols. This study provides insights into rational design of Co-based catalysts for efficient syngas conversion to C2+ alcohols.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3995-6
The deployment of single-site metal catalytic nodes into zirconium-based metal-organic frameworks (Zr-MOFs) offers vast advantages in catalytic recyclability, product separation, and mechanistic analysis, underscoring their paramount significance in heterogeneous catalysis. Nonetheless, their occupation within pores/channels usually diminishes mass transfer and catalytic efficiency during reactions such as the hydroboration of carbonyl compounds, especially for bulkier substrates. To address this issue, three microporous single-site Ti(IV) embedded Zr-MOFs with sequentially extended ligand arms are novelly synthesized to enable precise pore modulation ranging from 9.04, 10.12, to 11.18 Å. The catalytic performance is investigated using eight carbonyl compounds of varying sizes and four additional larger-scale substrates, which demonstrates that the catalytic efficiency is increased through pore size regulation, yet still away from optimal catalytic performance. Then a further strategy was shifted to the linker installation of linear dicarboxylate ligands chelated single-site Ti(IV) within coordination-unsaturated windows of mesoporous Zr-MOFs, and the result elucidates that the obtained catalyst exhibits superior catalytic efficiency (all exceeding 90%) while preserving the inherent mesoporosity of Zr-MOFs with a pore size of approximately 21.73 Å. We believe this research provides critical guidance for future research on structural design and catalytic optimization of MOFs, opening new avenues in heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4037-1
Nasopharyngeal carcinoma (NPC) poses a therapeutic challenge due to its anatomical complexity and the limitations of conventional treatments in achieving precise targeting and sufficient efficacy. Here, we report a multifunctional platform based on heat-triggered electrospray self-healing porous poly(lactic-co-glycolic acid) (PLGA) microspheres encapsulating indocyanine green (ICG), sequentially coated with a tannic acid-Fe3+ (TAF) metal-phenolic network and fibronectin (FN) for targeted photothermal/chemodynamic combination therapy. The resulting functional microspheres (PI-TAF@FN) exhibit an average size of 1.9 μm, excellent colloidal stability, heat-induced self-healing performance, and a high photothermal conversion efficiency of 51.4%. These microspheres specifically target NPC cells via FN-mediated integrin recognition, enabling ICG/TAF-mediated photothermal therapy under 808-nm laser irradiation and TAF-mediated chemodynamic therapy, leading to enhanced cancer cell apoptosis in vitro. In a mouse NPC model, the combined photothermo-chemodynamic therapy achieved effective tumor treatment with minimal systemic toxicity. Furthermore, the dual TAF and ICG components allow multimode FN-targeted T1-weighted magnetic resonance/fluorescence/thermal imaging for precision NPC management. This electrospray self-healing porous microsphere platform offers a unique theranostic strategy that can integrate diverse therapeutic and diagnostic components for precision oncology.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60681-0
The escalation of global warming and climate change necessitates the development of clean energy carriers. Hydrogen, with a high combustion value of 120 MJ/kg and net-zero carbon emissions, is a promising alternative. Catalytic methane pyrolysis offers a route to produce high-purity hydrogen and functional carbon materials simultaneously. However, challenges persist in catalyst deactivation due to carbon deposition and the efficient separation and valorization of carbon byproducts. This review systematically examines recent progress in solid and molten-medium catalysts for methane pyrolysis. It highlights strategies to enhance catalyst stability, including precise control of active sites, alloying, support optimization, and tuning the carbon-catalyst interface. The introduction of molten media catalytic systems, which feature dynamically refreshed gas-liquid interfaces, can fundamentally mitigate deactivation and facilitate continuous carbon separation. The paper discusses reaction mechanisms, catalytic performance, and control of carbon morphology, along with strategies for efficient separation and purification of carbon products in molten media. High-value applications of the produced carbon materials are also explored. The review underscores the potential of methane pyrolysis as a low-carbon technology for hydrogen production, while identifying key research directions for industrial scalability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4175-3
The precise manipulation of microdroplets (diameter < 20 μm) on solid substrates is critical for applications in environmental monitoring, targeted drug delivery, clinical diagnostics, and public health. A major challenge is contact angle hysteresis (CAH), which pins droplets and impedes mobility. Here, we introduce a crack-mediated capillary bridging strategy for efficient capture and directional transport of microdroplets. The approach employs a stretchable elastomeric substrate with island-like microstructures. Under longitudinal tensile stress, controlled fracture generates densely packed, directionally oriented surface cracks. These fissures induce localized capillary forces that counteract adhesion-induced resistance, enabling programmable droplet motion. Experiments capturing airborne pathogenic agents demonstrated a 14.2-fold enhancement in enrichment efficiency compared to flat surfaces. This work integrates fracture mechanics with capillary-driven fluid dynamics, establishing a framework for next-generation microfluidic systems. The findings offer promising avenues for biosensing, pollutant analysis, and interdisciplinary applications.