SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3890-6
Photothermal catalysis offers a sustainable route for CO2 conversion to value-added chemicals, yet precise control of active sites and light-harvesting materials remains challenging. Here, we report the rational integration of three-dimensional ordered macroporous (3DOM) CeO2 with positively charged (Niδ+)n clusters to construct efficient photothermal catalysts for the reverse water gas shift (RWGS) reaction. The 3DOM architecture enhances light absorption, improves access to active sites, and provides a confined environment for reactant enrichment. Engineering (Niδ+)n clusters within 3DOM CeO2 not only affords highly active sites for H2 adsorption and dissociation but also modulates the local structure of CeO2 to promote CO2 adsorption and activation. Furthermore, the (Niδ+)n clusters significantly enhance light-harvesting capability across the UV-vis-NIR spectrum, generating a pronounced photothermal effect that accelerates reaction kinetics. The optimized (Niδ+)n/CeO2 catalyst exhibits outstanding photothermal catalytic performance, achieving a CO production rate of 63.36 mmol g−1 h−1 in a flowing reaction with CO selectivity of 93% under simulated solar irradiation (2.6 W cm−2). Theoretical calculations reveal that the (Niδ+)n/CeO2 catalyst reduces the thermodynamic energy barrier for *COOH formation in CO2 hydrogenation. This study offers valuable insights into the design of photothermal catalysts, highlighting the significant potential of active-site engineering in promoting efficient CO2 conversion for practical solar-to-fuel production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3875-1
Photocatalytic hydrogen evolution reaction (HER) from pure water is a promising strategy to address critical challenges in energy sustainability and environmental remediation. However, HER over single-component photocatalysts is intrinsically limited by inefficient carrier separation and relatively poor photostability. Forming abundant interfaces between two components is an effective approach for solving these issues. Herein, a series of hierarchical core-shell heterojunction photocatalysts, designated as F@Z-X, was rationally constructed by in situ growing ZnIn2S4 (ZIS) nanosheets on a Ti-based metal-organic framework (FIR-125), demonstrating remarkable structural stability. Due to the abundant intimate contact interfaces and well-matched band structure, the F@Z-X series exhibit enhanced HER performance. Among them, the optimized heterojunction [email protected] shows a photocatalytic hydrogen evolution rate of 3789.45 μmol g−1 h−1, which is about 4.4 and 264.4 times higher than that of pristine ZIS (859.57 μmol g−1 h−1) and FIR-125 (15.32 μmol g−1 h−1), respectively. Moreover, the photocatalyst manifests excellent reusability and durability, maintaining its performance over five consecutive cycles and sixteen hours of continuous reaction. The outstanding performance of [email protected] may be ascribed to an optimal balance among three fundamental photocatalytic processes: sufficient light absorption, exceptional carrier separation, and appropriate surface reaction. This work offers valuable insights into the rational design and controllable synthesis of novel heterojunction photocatalysts for efficient hydrogen evolution.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050803
This study systematically investigates the synergistic drag reduction mechanism of surfactants and porous media in coal seam water injection. Four surfactant types—cationic CTAB, anionic SDBS, amphoteric BS-12, and nonionic OP-10—were tested with five porous media pore sizes (3–12 mm) using a custom-built all-in-one drag reduction test system. The effects of surfactant type, mass concentration, driving frequency, and pore diameter on drag reduction efficiency were evaluated. Results show that in an empty tube, drag reduction efficiency increases with mass concentration. As driving frequency increases, drag reduction first rises then falls, peaking at 35 Hz. With porous media, drag reduction exhibits pore size dependence, reaching a maximum at 8 mm and decreasing thereafter. The composite surfactant-porous media system achieves synergistic enhancement over single systems. At 0.05% mass concentration, all surfactants attain maximum drag reduction, with CTAB showing the highest efficiency. Optimal conditions (0.05% CTAB, 35 Hz, 8 mm pore size) yield a drag reduction rate of 66.14%, a 1.4-fold improvement over 20 Hz. These findings demonstrate that tailoring surfactant and porous media parameters can significantly optimize coal seam water injection efficiency, offering a practical approach for dust control in mining.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.