SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507064
This study investigates pollutant removal characteristics and kinetic behaviors in sewage networks, and analyzes their impact on the carbon-to-nitrogen ratio (C/N, as COD/TN) of influent to wastewater treatment plants. Source water quality sampling at drainage outlets revealed spatial and temporal variations in C/N, with domestic sewage exhibiting higher C/N than industrial sewage, and diurnal peaks reaching 6.92 versus 4.71 during off-peak hours. Using a pilot-scale adjustable sewage network system in Kunshan, experiments were conducted under high (0.491 m·s−1) and low (0.089 m·s−1) flow velocities, monitoring pollutant removal over 144 hours. Pseudo-first-order kinetics were applied to model COD and TN removal. Results showed that COD (including SCOD and PCOD), BOD5, and SS achieved approximately 80% removal within 144 h, with higher removal at low flow velocity. TN, NH3-N, and TP exhibited lower overall removal rates. Kinetic fitting revealed that COD removal rate constants (kCOD) were significantly higher than those for TN (kTN), and both decreased with increasing flow velocity: at low velocity, kCOD=0.0167 h−1 and kTN=0.0029 h−1; at high velocity, kCOD=0.0127 h−1 and kTN=0.0020 h−1. Simulations based on actual source pollutant concentrations indicated that the time for C/N to drop to the denitrification critical value of 4.50 was 12.24 h at high velocity, but shortened to 9.49 h at low velocity. These findings demonstrate that increasing flow velocity effectively retards the decline of C/N. Therefore, regulating network flow velocity to reduce hydraulic retention time is a key strategy for maintaining adequate C/N at the terminal and ensuring denitrification efficiency in wastewater treatment plants.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61116-X
A standardized dataset of linear sweep voltammetry (LSV) curves is presented for evaluating the oxygen reduction reaction (ORR) performance of carbon-supported catalysts in acidic media. All electrochemical tests were conducted in O2-saturated 0.5 mol L−1 H2SO4 at controlled rotation speeds using a rotating disk electrode. The dataset comprises 120 validated entries from both non-precious metal (MNC) and platinum-based (Pt-MC) catalysts, including original LSV curves and extracted performance parameters such as onset potential, half-wave potential, and limiting current densities at different rotation speeds. Data processing involved potential conversion to the reversible hydrogen electrode (RHE) scale, background subtraction, outlier removal, and reproducibility checks with defined quality control thresholds (relative standard deviation ≤2% for E1/2 and ≤5% for limiting current). The standardized collection serves as a reliable benchmark for catalyst performance comparison, supports kinetic and mass transport analysis, and provides a structured data source for machine learning applications in electrocatalysis. The dataset is openly available via Science Data Bank, with a DOI, and is intended as a dynamic resource for the ORR electrocatalysis community.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508053
Polycyclic aromatic hydrocarbons (PAHs) in industrial soils pose significant risks due to their hydrophobicity and low bioavailability, limiting the efficacy of bioremediation. This study investigated the enhancement of an in-situ electrokinetic-biological barrier (EK-BB) system for PAH-contaminated soil using biosurfactants. Three biosurfactants—rhamnolipid (RL), alkyl polyglycoside (APG), and saponin (SAP)—were applied individually and in combinations at 10× critical micelle concentration (CMC), and the optimal RL+APG mixture was further tested at 2.5, 5.0, 7.5, and 10× CMC. Results showed that biosurfactant application improved soil electrical current, moisture retention, and PAH removal. Combined surfactants outperformed single ones, with the 10× CMC RL+APG treatment (Exp IV) achieving the highest average current intensity and moisture content, 1.31 and 1.12 times that of the control (CK), respectively, and a PAH removal of 106.02 mg·kg⁻¹. Biosurfactants also promoted bacterial growth in both contaminated soil and the biobarrier layer; the 10× CMC RL+APG treatment increased bacterial counts by 6.24-fold and 44.8%, respectively. However, excessive surfactant concentrations led to PAH accumulation in the biobarrier and clean soil. The 5× CMC RL+APG treatment provided optimal balance, maximizing PAH removal while maintaining barrier effectiveness. These findings confirm that appropriate biosurfactant concentrations can enhance EK-BB remediation, offering technical support for PAH-contaminated site remediation and safe reuse.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011302
Heavy metal contamination in soil severely compromises the quality and safety of Alisma orientale medicinal materials, and consumption of contaminated herbal preparations poses health risks. To characterize contamination and risks in Sichuan's genuine producing areas, 159 paired soil and plant samples were collected. Concentrations of Cu, Zn, Pb, Cd, and Ni were determined via ICP-OES. Soil pollution was assessed using the Single Pollution Index (Pi), Nemerow Comprehensive Index (Pn), and Potential Ecological Risk Index (RI). Human health risks from heavy metals in Alisma were evaluated via Target Hazard Quotient (THQ) and Hazard Index (HI). Mean soil concentrations were Cu 29.57, Zn 61.86, Pb 29.51, Cd 1.77, and Ni 28.08 mg·kg−1. Except for Cd, all elements were below agricultural soil screening values. Pi and Pn confirmed Cd contamination, with Cd posing slight to strong potential ecological risks. Cu, Cd, Pb, and Ni showed highly significant positive correlations, indicating common origins. Heavy metal concentrations in Alisma did not exceed pharmacopeial limits. The plant exhibited strong Zn enrichment but weak accumulation of Cu, Cd, and Pb, and negligible Ni enrichment. THQ and HI values indicated no potential health risks under current exposure. Quantitative assessment is critical for soil pollution control, safe cultivation, and medication safety.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011101
This study investigates the adsorption characteristics and mechanisms of Cd, Ni, and Pb on yellow soils collected from multiple sites in Guizhou Province, China. Soil physicochemical properties, potentiometric titration, adsorption edge experiments, and a 1-site/2-pKa surface complexation model (SCM) were integrated to derive acid-base parameters and metal adsorption constants. Linear regression models established quantitative relationships between SCM parameters and soil properties, enabling prediction of adsorption behavior for new soil samples. Results showed that adsorption capacities increased with pH and followed the order Pb > Ni > Cd, influenced by hydrated radius, hydrolysis constant, and electronegativity. Soils with higher surface site concentration (Hs) and lower point of zero charge (pHpzc) exhibited greater metal adsorption. The SCM fitted adsorption edges with R ≥ 0.94, confirming its validity. pH was the dominant factor controlling metal complexation constants (lgKSOMe), acid-base equilibrium constants, and surface site density (Ds), with influence order Pb > Ni > Cd. Free iron oxide correlated negatively with deprotonation constant (pKa2). Ds was also affected by cation exchange capacity and specific surface area. Validation using a separate set of soil samples yielded good agreement between predicted and measured adsorption (R² = 0.75–0.82, RMSE = 0.1–0.51). This combined modeling approach simplifies experimental procedures and offers a robust tool for assessing heavy metal environmental risks and remediation strategies.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025081103
Nitrous acid (HONO) is a critical precursor of hydroxyl radicals (·OH) in the atmosphere, influencing oxidative capacity and secondary pollutant formation. However, model simulations often underestimate HONO concentrations, and its role in nitrate formation remains unclear. This study investigates a typical winter haze episode in Guangzhou (January 2021, peak PM2.5: 243.0 μg·m−3) using observational data and a box model to quantify HONO sources and assess their impact on ·OH and particulate nitrate. HONO concentrations increased from (1.0±1.0) μg·m−3 during clean periods to (9.2±3.8) μg·m−3 during polluted periods, while nitrate rose from (6.4±3.4) to (43.3±20.0) μg·m−3 (6.8-fold). Incorporating seven additional HONO sources improved simulated daytime HONO from (0.3±0.1) to (6.5±2.3) μg·m−3, matching observations. Source apportionment showed direct vehicle emissions dominated (49.7%), followed by heterogeneous photosensitized reaction of NO2 on aerosol surfaces (23.0%), ground surface reaction (10.7%), and nitrate photolysis (8.7%). With optimized HONO, simulated daytime ·OH increased from (0.6±0.3)×10^6 to (1.5±0.8)×10^6 molec·cm−3 (1.2-fold), and nitrate production via ·OH+NO2 increased from (3.4±1.2) to (15.3±8.5) μg·m−3·h−1 (3.5-fold). The simulated-to-observed nitrate ratio improved from 21% to 81%. Sensitivity tests indicated that setting nitrate photolysis enhancement to 100 times gaseous nitric acid yielded better HONO and nitrate simulations. This study underscores the importance of refining HONO sources for accurate simulation of atmospheric oxidation and nitrate formation, aiding pollution control strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3937-7
Triple-negative breast cancer (TNBC) remains a formidable clinical challenge due to its high invasiveness and adaptive resistance. We report a bio-mimetic nanoplatform (HMPB-GOx@HSA-Cu2+) integrating starvation therapy, Fenton/Fenton-like catalysis, and mild photothermal therapy (mPTT) for synergistic TNBC treatment. The nanoreactor comprises a hollow mesoporous Prussian blue (HMPB) core loaded with glucose oxidase (GOx), encapsulated in a human serum albumin (HSA) shell covalently functionalized with Cu2+ ions. This design enables spatiotemporal control of Cu2+-mediated Fenton catalysis, responding to the tumor microenvironment (TME) to generate cytotoxic hydroxyl radicals (·OH). GOx catalyzes glucose depletion, elevating H2O2 levels and acidity, thereby enhancing catalytic efficiency. Concurrently, mPTT at ~43–45°C accelerates the Fenton reaction and suppresses heat shock protein (HSP) expression, overcoming thermal tolerance via ATP depletion. In vitro and in vivo studies demonstrate significant anti-tumor efficacy through reactive oxygen species (ROS) accumulation and metabolic disruption, with excellent biocompatibility. This work presents a highly integrated strategy for precise TNBC therapy, addressing limitations of conventional monotherapies.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040401
Conventional zero-valent iron (ZVI) suffers from limited electron transfer due to its dense surface oxide layer. This study introduces a mechanochemical ball-milling strategy incorporating sodium chloride (NaCl) with ZVI to fabricate chloride-modified ZVI (Cl-ZVIbm). Using hexavalent chromium (Cr(VI)) as a model pollutant, Cl-ZVIbm exhibited a 76.5-fold enhancement in removal kinetics (0.0306 min−1 vs. 0.0004 min−1) compared to ball-milled ZVI (ZVIbm), achieving complete removal of 2 mg·L−1 Cr(VI) within 120 min. Spectroscopic characterization and density functional theory (DFT) calculations revealed dual regulation mechanisms: (1) Cl− substitution of surface hydroxyl groups alters coordination environments, enabling Cr(VI) adsorption via a bidentate binuclear configuration with adsorption energy reduced from –0.28 eV to –1.64 eV; (2) The strong electron-withdrawing effect of Cl− drives directional electron migration from the iron core to the surface, increasing surface Fe(II) content by 26.9% (67.5% vs. 53.2%) and facilitating direct electron transfer to reduce 99.5% of Cr(VI) into low-toxicity Cr(III). Notably, chloride leaching during reactions was only 0.0126 mmol·L−1, far below industrial wastewater discharge standards, confirming environmental compatibility. This work provides atomic-scale insights into chloride-mediated electronic modulation on ZVI surfaces, offering novel principles for interfacial engineering of environmental functional materials and a theoretical basis for heavy metal remediation technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3950-x
Photocatalytic oxygen reduction reaction (ORR) for hydrogen peroxide (H2O2) production via the two-electron pathway offers an environmentally friendly oxidant and a clean fuel. However, challenges exist in optimal oxygen (O2) adsorption capacities and maintaining O–O bond during O2 activation. Herein, we present a zinc single-atom catalyst (Zn/VN-CN) incorporating nitrogen vacancies (VN), designed to modulate the electronic structure of the photocatalyst, leading to optimized O2 adsorption energy and a remarkable enhancement in H2O2 yield. Benefiting from the synergistic effect between nitrogen vacancies and Zn single atoms, the optimized Zn/VN-CN catalyst exhibits a photocatalytic H2O2 production rate of 2.399 mmol g−1 h−1 under visible-light irradiation, representing a 12-fold enhancement compared to pristine g-C3N4 (CN), along with a high H2O2 selectivity of 87.4%. Combined experimental and theoretical studies indicate that the Zn-N3 sites act as highly active reaction centers, while nitrogen vacancies increase the charge density and downshift the d-band center of the Zn sites, thereby moderating O2 adsorption strength, lowering the activation energy barrier for the formation of *H2O2, and further converting it to H2O2. This work proposes an effective strategy for tuning O2 adsorption behavior to achieve highly selective and active photocatalytic H2O2 production.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511054
A novel S-scheme heterojunction photocatalyst, Bi6O5(OH)3(NO3)5·3H2O/BiOBr0.8I0.2 (BON@BI), was synthesized via a one-step hydrothermal method using Bi6O5(OH)3(NO3)5·3H2O (BON), KBr, and KI as precursors. The mass ratio of BON to BiOBr0.8I0.2 (BI) was optimized, revealing that the 20% BON@BI composite (BON@BIOPT) exhibited the highest visible-light photocatalytic activity. Under 30 min of visible-light irradiation, BON@BIOPT achieved a 99.8% degradation efficiency of Rhodamine B (RhB), approximately twice that of pristine BI (52.2%). The composite displayed a rod-like morphology with uniform nanosheets, and its specific surface area increased from 32.54 m²·g⁻¹ (BI) to 44.7 m²·g⁻¹. The absorption edge red-shifted from 560 nm (BI) to 580 nm, narrowing the bandgap from 2.55 eV to 2.43 eV. The S-scheme heterojunction formed between BON and BI generates an internal electric field that effectively suppresses recombination of strongly reducing photogenerated electrons and strongly oxidizing holes, with superoxide radicals (O₂•⁻) and holes (h⁺) identified as the primary reactive species. BON@BIOPT exhibited excellent stability, retaining 88.6% degradation efficiency after seven consecutive cycles. It also demonstrated robust environmental adaptability, maintaining 85–98% degradation efficiency under various pH conditions and in the presence of interfering anions. The degradation pathway of RhB involves N-de-ethylation, cleavage of the conjugated chromophore, and deamination, ultimately mineralizing into low-molecular-weight organics, inorganic salts, CO₂, and H₂O. These results underscore the potential of BON@BIOPT for practical remediation of organic pollutants in water.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0003
Phosphorus and transition metal-modified ZSM-5 zeolites were prepared via incipient wetness impregnation and characterized by XRD, N2 adsorption-desorption, and pyridine-IR spectroscopy. The effects of modified zeolites on catalytic pyrolysis of n-heptane, 3-methylhexane, and methylcyclohexane were systematically investigated, revealing the structure-activity relationship between acid properties and catalytic performance. Results indicate that phosphorus and transition metal modification can regulate the L/B acid ratio of ZSM-5, which significantly influences product distribution. An excessively high L/B acid ratio promotes hydrogen and coke formation, leading to pore blockage and reduced conversion, whereas an appropriate L/B acid ratio facilitates mild dehydrogenation, enhancing ethylene and propylene yields. Reactant conversion followed the order: n-heptane > 3-methylhexane > methylcyclohexane. Efficient conversion of 3-methylhexane and methylcyclohexane requires catalysts with high L acid amount, strong Brønsted acid amount, optimized L/B acid ratio, as well as high specific surface area and micropore specific surface area. This study provides critical insights for designing high-efficiency alkane pyrolysis catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4065-6
Industrial-scale hydrogen production from seawater is a paramount goal for a sustainable energy future, yet it is severely hampered by the rapid deactivation of electrocatalysts under harsh operating conditions. Here, we introduce a robust self-supporting aerogel catalyst designed to address the two intertwined challenges of activity and stability in high-current-density seawater electrolysis. Our strategy involves creating strong metal-support interactions by anchoring ultrasmall platinum nanoparticles onto a porous N-doped carbon aerogel (Pt@N/CFP). Theoretical calculations reveal that this unique Pt-N interface serves a dual critical function: it not only lowers the kinetic barrier for water dissociation but also creates an electronic shield that effectively prevents chloride ion poisoning of the Pt active sites. When implemented as the cathode in a practical anion-exchange membrane (AEM) electrolyzer, the Pt@N/CFP catalyst demonstrates exceptional performance, achieving a low cell voltage of 1.688 V at an industrial-grade current density of 1000 mA cm−2 and maintaining outstanding stability for over 300 h. This work provides guidance for creating exceptionally durable catalysts capable of withstanding extreme electrochemical environments.