SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4249-2
Underwater bubble manipulation is critical for water electrolysis, heat transfer, and mineral flotation, yet existing strategies relying on buoyancy or Laplace gradient forces from asymmetric surface geometries suffer from limited flexibility and narrow applicability. This work introduces a temperature-responsive anisotropic cilia surface (TRAS) that achieves bidirectional long-range bubble transport by modulating elastic modulus and stiffness. The TRAS enables precise control over the asymmetric three-phase contact line and viscous resistance, facilitating reversible bubble motion. Experimental validation using aqueous ethanol droplets with varying surface tensions (73.16 mN/m for 0 vol% to 22.27 mN/m for 100 vol%) on cilia with center-to-center spacings of 0.2–1.0 mm reveals that transport direction depends on both cilia spacing and liquid surface tension. Droplets of 0 vol% and 20 vol% ethanol exhibit sustained reverse transport on hard cilia, while 60 vol%, 80 vol%, and 100 vol% solutions show sustained forward transport. Notably, 40 vol% ethanol droplets display bidirectional transport at 0.6 mm spacing, reverse transport at 0.8 and 1.0 mm, and forward transport at 0.2 and 0.4 mm. These results demonstrate that tuning surface tension and cilia spacing provides a versatile platform for directional bubble manipulation, with promising applications in heat transfer, electrochemistry, and gas handling systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3803-8
The molecular copolymerization of donor-acceptor (D-A) interactions has been effectively utilized to modulate the charge transfer dynamics in polymeric carbon nitride (PCN) photocatalysts. Herein, a D-A configured photocatalyst (TPCN) was constructed by copolymerizing 4,4’,4’’-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT) as the electron donor with triazine units (electron acceptor). The unique propeller structure of TAPT, combined with the triazine framework, expanded the π-conjugated system and induced a strong built-in electric field (BIEF) across the D-A configuration. Theoretical calculations and transient absorption spectroscopy revealed that this synergistic effect facilitated intramolecular charge separation and widened the range of light absorption, indicating accelerated charge transfer and suppressed recombination in TPCN. The optimized TPCN3 sample exhibited dramatically enhanced photocatalytic H2O2 production (1.74 mmol g−1 h−1), representing a 13.4-fold increase over pristine PCN. Additionally, the TPCN3 sample also exhibited significantly faster degradation kinetics than PCN counterpart toward various emerging contaminants. This work demonstrates a promising strategy for designing efficient metal-free photocatalysts for sustainable H2O2 production and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3547-7
Inorganic perovskite solar cells (IPSCs) have attracted significant attention due to their excellent light and thermal stability and potential in tandem applications. However, their efficiency and stability are often limited by residual lattice stress and defects at interfaces and within the bulk, causing severe nonradiative recombination. Here, we introduce a zero-dimensional supramolecular complex, (ETP)2SbCl5, as a dual-interface and bulk modifier to regulate CsPbI3 film growth. The modifier exhibits spatial segregation: ETP+ cations anchor at the buried interface, passivating defects on TiO2 and perovskite surfaces; Sb3+ and Cl− ions diffuse into the bulk during annealing, relieving residual stress; and Cl− accumulates on the top surface, passivating cation defects. Consequently, the modified CsPbI3 solar cell achieves a power conversion efficiency (PCE) of 21.71% and an open-circuit voltage (VOC) of 1.27 V, retaining 97.4% of initial efficiency after 500 h of maximum power point (MPP) tracking. This work demonstrates a synergistic strategy to simultaneously address interfacial and bulk defects, advancing high-performance and stable inorganic photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3727-0
Lead halide perovskites are promising scintillators for X-ray imaging due to high X-ray absorption efficiency, excellent luminescence, and facile synthesis. However, their ionic nature challenges simultaneous high photoluminescence efficiency and environmental robustness. This work introduces a multilevel encapsulation strategy: CsPbBr3 quantum dots (QDs) are sequentially coated with Cs4PbBr6, SiO2, and polydimethylsiloxane (PDMS). Cs4PbBr6 passivates surface defects, while SiO2 and PDMS provide barriers against moisture, heat, and radiation. The resulting CsPbBr3@Cs4PbBr6/SiO2/PDMS flexible films exhibit a photoluminescence quantum yield (PLQY) of 85%, outstanding mechanical flexibility, and durability under stretching, bending, and compressing. Films retain emission stability under elevated temperatures, prolonged X-ray irradiation, and extended water immersion. X-ray imaging demonstrates spatial resolution of 12 lp/mm, enabling distortion-free imaging of curved objects; superior water resistance allows long-term underwater imaging. This work highlights hierarchical encapsulation in balancing luminescence efficiency and stability, offering a pathway toward practical flexible perovskite scintillators.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3773-7
Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells suffer from significant open-circuit voltage (VOC) deficits due to severe interfacial and bulk recombination, restricting their power conversion efficiency (PCE) far below the Shockley-Queisser limit. This work proposes a low-temperature annealing strategy during ITO sputtering (SA) to synergistically address these challenges. The temperature applied during ITO sputtering not only improves the crystallinity, carrier concentration, and optical transmittance of the ITO layer but also promotes the diffusion of In from ITO into both CdS and CZTSSe layers. Consequently, lattice matching at the CZTSSe/CdS interface is optimized, enabling epitaxial growth. And a favorable ITO/In:CdS/In&Cd:CZTSSe structure with optimal band alignment is obtained. As a result, a champion device with a PCE of 14.29% was achieved. The SA-treating also enabled the CZTSSe solar cells to achieve the highest VOC reported to date, exceeding 590 mV. This underscores the essential role of SA processing in optimizing interface engineering and suppressing defects, thus promoting the development of low-cost, high-performance kesterite photovoltaics.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61069-4
Four-directional dual-matrix C/C composites were fabricated from PAN-based carbon fibers using a combined approach of soft-hard hybrid weaving preform molding, chemical vapor infiltration (CVI) of pyrolytic carbon (PyC), and high-pressure impregnation and carbonization of pitch-derived carbon. The ablation resistance was evaluated in a dual-pulse solid rocket motor, and the ablation behavior was investigated. The carbon rods, formed by twisting and carbonizing fiber bundles, exhibited a hexagonal cross-section, surrounded by a dense PyC 'wall' structure. The linear ablation rates after pulse I and pulse II were 0.068 mm/s and 0.113 mm/s, respectively. A cellular-like PyC layer and nanowire structures were deposited on the surface of the throat convergent section during the post-combustion cooling phase, while cracks and delamination occurred on and within the divergent section. The ablation process involved ultra-high temperatures, high-speed gas scouring, oxygen-containing thermochemical ablation, and thermal shock. This work elucidates the ablation behaviors under dual-pulse conditions and provides technical guidance for designing C/C composites for extreme environments.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604004
Tire wear particles (TWPs) are emerging pollutants and constitute the dominant type of microplastics (MPs) in urban stormwater runoff, accounting for up to 90% of MPs in some cases. They are characterized by small size, high mobility, complex composition, and significant toxicity. Current research on TWPs remains fragmented, lacking a comprehensive understanding of their environmental behaviors and pollution control in aquatic systems. This review systematically analyzes the enrichment and vectoring roles of TWPs for coexisting pollutants, and their environmental fate, including ecotoxicological impacts, detection methodologies, release of intrinsic additives, and aggregation and sedimentation behaviors. Drawing on insights from other microplastic studies, the paper explores control technologies across the pollution pathway—source, transport, and terminal treatment—and proposes feasible management strategies. Key findings indicate that TWPs can adsorb heavy metals and organic contaminants, with adsorption capacities influenced by aging processes. Their aggregation is governed by solution chemistry, with critical coagulation concentrations varying with ionic strength and pH. The release of additives such as zinc and benzothiazoles is significant, posing ecological risks. Future research should focus on real-water aggregation mechanisms, additive release under natural conditions, long-term performance of treatment facilities like constructed wetlands under TWPs stress, enzymatic degradation pathways, and integration of AI, big data, and IoT for cost-effective detection and risk modeling. This review provides a scientific basis for developing targeted pollution control measures for TWPs in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012404
Antibiotics, widely used for disease prevention and growth promotion in livestock, are emerging contaminants with potential risks to human health via the food chain. This review systematically analyzed the sources and residual levels of tetracycline (TCs) and β-lactam antibiotics in raw, pasteurized, commercial, and ultra-high-temperature (UHT) sterilized milk from various countries between 2012 and 2024, based on quantitative detection methods such as LC-MS and HPLC. The highest concentrations of TCs were found in milk from Algeria and Iran, while β-lactam residues were most elevated in Algeria, Bangladesh, and Kenya. The predominant TCs were tetracycline, chlortetracycline, and oxytetracycline; β-lactams were mainly penicillin and amoxicillin. Health risk assessment using hazard quotient (HQ) and hazard index (HI) revealed that all individual HQ values were below 1, indicating no significant non-carcinogenic risk from single antibiotics. However, the HI for multiple antibiotics in raw milk from Algeria exceeded 1, suggesting potential cumulative health risks. Furthermore, some studies reported residue concentrations surpassing maximum residue limits (MRLs), underscoring the need for continuous monitoring and control. This review highlights the global variability in antibiotic contamination and the importance of comprehensive risk assessment to safeguard public health.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3812-5
Anaerobic bacterial infections, prevalent in oxygen-deprived tissues, are recalcitrant to conventional antibiotics due to slow bacterial metabolism and the generation of nutrient-rich niches that foster polymicrobial biofilms. Propionibacterium acnes (P. acnes), a skin commensal, exemplifies this challenge, causing acne vulgaris and implant-associated infections, with rising antibiotic resistance. This study introduces an antimicrobial peptide (AMP), WRK (sequence: WRKFRRFKFRW-NH2), which induces endogenous reactive oxygen species (ROS) production in anaerobic bacteria, exploiting their inherent low ROS tolerance. WRK exhibited potent antibacterial activity, with a minimum inhibitory concentration (MIC) of 4 μg mL−1 against planktonic P. acnes and a minimum biofilm eradication concentration (MBEC) of 64 μg mL−1. To enable dermal delivery, WRK was encapsulated in layered dissolving microneedles (MNs), which demonstrated adequate mechanical strength for skin penetration. In a mouse back acne model, AMP MNs significantly reduced P. acnes infection and inflammation, outperforming commercial clindamycin gel. Histological analysis confirmed reduced inflammatory cell infiltration and tissue hyperplasia in the AMP MN group. This strategy offers a promising approach for treating anaerobic infections without promoting drug resistance, addressing a critical unmet need in clinical dermatology and implant surgery.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0031
The high-temperature behavior of biomass ash critically influences gasifier operational efficiency. This study investigates the differential high-temperature behaviors of corn straw ash (CSA) and wheat straw ash (WSA) using an intelligent ash fusion analyzer, high-temperature rotating viscometer, X-ray diffraction (XRD), SEM-EDS, and FactSage thermodynamic simulations. Both ashes contain high K2O (>30%) and exhibit flow temperatures below 1300 °C. Despite higher K2O and lower SiO2, CSA exhibits a higher flow temperature (1241 °C) than WSA, attributed to elevated CaO (10.39%) and MgO (7.33%) that promote formation of high-melting silicates (K2MgSiO4, K2Ca2Si2O7, CaSiO3). In contrast, WSA with lower CaO (4.92%) and MgO (2.82%) tends to form low-melting potassium silicates. At high temperatures, both slags are typical crystalline slags, with viscosity rising sharply below a critical temperature. For CSA, rapid nucleation and coarsening of silicate crystals (e.g., KAlSiO4 grain size increases from 20.5 nm at 1350 °C to 192.9 nm at 1050 °C) cause abrupt viscosity increase. For WSA, a high P2O5 content (10.05%) induces a 'chemical dilution effect', leading to persistent KAlSiO4 during cooling and elevated viscosity, especially at the final cooling stage. This study elucidates how ash chemical composition governs high-temperature phase equilibrium and non-equilibrium kinetics, thereby macroscopically affecting ash fusion and rheological behavior, providing a theoretical basis for deeper understanding of biomass ash high-temperature characteristics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031001
The diffusive gradients in thin-films (DGT) technique has emerged as a promising tool for assessing the desorption kinetics and bioavailability of organic contaminants in soil. This study compared DGT, soil solution, and organic solvent extraction methods for evaluating the bioavailability of four sulfonamide antibiotics (SAs) in soil using pot experiments with Brassica rapa subsp. chinensis and Lactuca sativa. Results demonstrated that plant uptake of SAs depended on compound properties and plant species, with roots as the primary accumulation site. DGT-measured concentrations (CDGT) showed significant linear correlations with SA concentrations in both roots and leaves, and effective concentrations (CE) were positively correlated with plant tissue levels (P < 0.05). The soil solution method also showed predictive ability but with lower stability. The mass of SAs adsorbed by DGT increased non-linearly with deployment time, indicating that solid-phase resupply sustained long-term DGT uptake. DIFS model-derived soil-water partition coefficients (Kdl) ranged from 0.23 to 1.25 mL·g−1, with higher Kdl values corresponding to greater bioavailability. Response times (Tc) ranged from 2307 to 7523 seconds, with sulfamethoxazole (SMZ) exhibiting the highest Tc, indicating its release was most constrained. Meta-analysis of desorption parameters for other organic contaminants revealed that soil pH and particle size were key determinants of Kdl, while molecular volume and hydrophobicity influenced resupply rates. This study confirms the reliability of DGT for assessing antibiotic bioavailability in soil and provides fundamental data on their migration and fate.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3923-x
Perovskite solar cells (PSCs) have achieved certified efficiencies exceeding 27%, rivaling silicon-based technologies, yet their operational stability under real-world conditions remains a critical barrier to commercialization. Exposure to full-spectrum sunlight, particularly ultraviolet (UV) radiation, coupled with diurnal temperature fluctuations and ingress of moisture and oxygen, induces multi-mode degradation pathways, including lattice distortion, defect accumulation, and interfacial strain. Conventional stabilization strategies typically address single degradation routes and rely on static passivation or fixed strain compensation, failing to adapt to the dynamic stress fields arising from thermal expansion-contraction cycles at buried interfaces. Here, we highlight a recent breakthrough by Zhou et al. that introduces a stepwise conformational engineering strategy to design multifunctional molecules capable of simultaneous UV shielding, dynamic strain regulation, and defect passivation. Starting from 1,1-diphenylethylene (DPE), which exhibits intrinsic UV absorption, a flexible octyl alkyl chain is incorporated to yield 1-octyl-2-(1-phenylvinyl)benzene (OPVB). The conformational freedom of the alkyl chain enables reversible thermal expansion and contraction, allowing in situ modulation of interfacial stress. Further functionalization with hydroxyl and carbonyl groups produces diethylamino hydroxybenzoyl hexyl benzoate (DHHB), which integrates all three targeted properties. This molecular design addresses the bottleneck of multi-mode degradation by providing dynamic stress management, UV protection, and defect healing, thereby enhancing device stability and performance. The work establishes a new paradigm for fabricating stable PSCs under realistic operating conditions, with implications for accelerating industrial deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4072-3
All-inorganic, hole-transport-material-free (HTM-free), carbon-based perovskite solar cells (C-PSCs) have attracted significant attention due to their exceptional stability and low cost. However, their performance and commercial potential are constrained by poor interfacial contact, insufficient crystallinity, and energy level misalignment. In this work, we address these challenges via a molecular engineering strategy by introducing tetrakis(4-ethynylphenyl)methane (TEPM) as a multifunctional additive. The alkynyl moiety (C≡C) in TEPM coordinates with Pb2+ ions in perovskite precursors, synergistically slowing crystallization kinetics to regulate crystal growth and passivate deep-level defects. Consequently, CsPbI3 films exhibit larger grain sizes, improved crystallinity, and lower defect densities. Devices modified with TEPM achieved a record power conversion efficiency (PCE) of 20.01% (certified 19.58%). Additionally, unencapsulated devices retained 87.6% of their initial efficiency after 1080 h under ambient conditions (25 °C, 30% relative humidity), and maintained 94.0% of their initial efficiency after 730 h of continuous AM 1.5G illumination in air. This work sets a new efficiency benchmark for inorganic HTM-free C-PSCs and provides a versatile molecular engineering strategy for developing high-performance, stable perovskite photovoltaics.