SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3604-1
Piezoelectric materials convert mechanical energy into electrical signals, enabling applications in sensors, actuators, and energy harvesting. Inorganic ceramics like PZT and BTO exhibit excellent piezoelectric properties but are brittle, limiting their use in flexible electronics. This work presents a porous composite of PZT@carboxymethyl chitosan (CMCS) in thermoplastic polyurethane (TPU). The core-shell structure enhances interfacial compatibility, while the porous TPU skeleton facilitates stress transfer and amplification, allowing high piezoelectric content. The resulting PZT@CMCS/TPU devices achieve an output voltage of 53 V and current of 13 μA, an 11-fold improvement over conventional PZT composite films. This approach enables flexible piezoelectric devices with high performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3665-2
Immuno-phototherapy faces a critical bottleneck: achieving high singlet oxygen (1O2) quantum yield and efficient photothermal conversion simultaneously under a single near-infrared (NIR) laser. Here, we report an acceptor-donor-acceptor (A-D-A) structured molecule, 3,9-bis(2-methylene-((3-(1,1-dicyanomethylene)-6/7-methyl)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']-dithiophene (m-ITIC), formulated into nanoparticles (NPs) via self-assembly with DSPE-PEG-NH2. The NPs exhibit strong NIR absorption and fluorescence at 688 and 768 nm, respectively. Under single-laser irradiation, they generate heat, superoxide anion (O2•−), and 1O2, with a 1O2 quantum yield of 56.8% and photothermal conversion efficiency (PCE) of 27.4%. This enables NIR fluorescence imaging-guided synergistic photodynamic therapy (PDT) and photothermal therapy (PTT). Notably, the nanoplatform induces PANoptosis—a coordinated cell death program integrating pyroptosis, apoptosis, and necroptosis—in tumor cells, amplifying immunogenic cell death (ICD). This triggers robust dendritic cell activation, macrophage polarization toward M1 phenotype, elevated CD8+ T cell infiltration, and suppression of immunosuppressive Treg cells, leading to significant tumor growth inhibition and prevention of lung metastasis in vivo. Therapeutic efficacy was validated in patient-derived tumor organoids, underscoring translational potential. This study presents a novel single-laser-activated nanoplatform that simultaneously mediates efficient photothermal and photodynamic effects and induces PANoptosis-driven ICD for synergistic cancer immunotherapy.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010302
Cadmium (Cd) contamination of agricultural soils poses significant economic and health risks. While extensive research has focused on Cd accumulation in staple crops like rice, data on oilseed crops remain scarce, hindering safety assessments of edible oils and oilseed meals. This study investigated Cd accumulation and translocation in rapeseed (Brassica napus) grown in You County, Hunan Province, a region severely contaminated with Cd. Rhizosphere soil and plant tissues (roots, stems, seeds) were collected and analyzed for Cd concentrations. Results showed that approximately 71% of rhizosphere soil samples exceeded the agricultural soil pollution risk screening value for Cd, indicating high ecological risk. Cd concentrations in roots and stems were (0.49 ± 0.39) mg·kg⁻¹ and (0.54 ± 0.31) mg·kg⁻¹, respectively, comparable to or higher than soil Cd levels (0.51 ± 0.31) mg·kg⁻¹, with elevated bioaccumulation and translocation factors. This suggests that improper disposal of rapeseed roots and stems, such as returning them to fields or burning, could lead to secondary Cd pollution. In contrast, Cd bioaccumulation and translocation factors in seeds were less than 1, and Cd concentrations in seeds, oil, and oilseed meals were relatively low. Comparative analysis with sesame, camellia oleifera, and peanut indicated that rapeseed-derived oil and meal contain lower Cd levels, positioning rapeseed as a promising low-Cd-accumulating edible oil crop for cultivation in Cd-contaminated areas.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3633-5
High-temperature interfacial diffusion in Half-Heusler (HH) thermoelectric devices poses significant challenges for practical applications, particularly the diffusion of Ag from conventional solders, which degrades material performance and device stability. This study reveals anomalous Ag diffusion through a Cr powder barrier layer into Ti0.5Zr0.5NiSn0.98Sb0.02, driven by Sn phase penetration. In contrast, employing a Cr foil barrier layer pre-densified the material, effectively preventing Sn phase penetration and eliminating Ag diffusion pathways, thereby preserving junction integrity. After aging at 973 K for 30 days, the Cr foil junction maintained a clean interface with a low contact resistivity of 0.27 μΩ cm2. Benefiting from this interfacial design, a Hf-free HH module achieved a high conversion efficiency of 10.4% at a hot-side temperature of 976 K, alongside long-term stability. This work addresses critical bottlenecks in developing high-performance, low-cost HH modules, facilitating their commercial application in waste heat recovery.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3407-0
Grain boundary (GB) engineering has emerged as a promising strategy to enhance the near-room-temperature performance of Mg3(Sb,Bi)2-based thermoelectric materials, yet effective control of Mg distribution at GBs remains a significant challenge. Here, we report a novel approach to achieve targeted Mg segregation at GBs through strategic Ag incorporation in Mg3.3Sb0.5Bi1.497Te0.003. Through comprehensive microstructural characterization and first-principles calculations, we demonstrate that Ag preferentially segregates at GBs, forming Mg-rich MgAg alloy phases while maintaining limited solid solubility within the matrix. This unique GB architecture simultaneously optimizes multiple thermoelectric parameters: the Mg-rich GB regions significantly provide efficient carrier transport channels and enhance carrier mobility, while the MgAg phases and lattice disorders effectively scatter phonons without disrupting electron transport. Consequently, the optimized composition (x = 0.01) exhibits a remarkable enhancement in power factor at 300 K and maintains an average ZT of ~1.0 across 300–400 K. The material also demonstrates excellent mechanical properties and thermal stability, making it particularly suitable for near-room-temperature applications. Our findings not only establish an effective strategy for GB engineering in Mg3(Sb,Bi)2 systems but also provide valuable insights into the rational design of high-performance thermoelectric materials through interface modification.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3750-6
SnSe is a promising thermoelectric material for medium-temperature applications due to its ultralow lattice thermal conductivity. However, the poor electrical conductivity of n-type polycrystalline SnSe significantly hinders its practical application. Here, we propose a dual-functional strategy employing InBr3 doping to synergistically enhance electrical transport while suppressing lattice thermal conductivity. For the first time, we demonstrate the successful construction of a Br-enriched conductive network within the SnSe matrix. The incorporation of In3+ and Br− introduces high-density charge carriers, while Br forms percolative conductive networks, resulting in a remarkable enhancement of carrier mobility to ~20.64 cm2 V−1 s−1. Simultaneously, the lattice thermal conductivity is substantially reduced to ~0.25 W m−1 K−1 through the formation of multi-scale defects, including dislocations and Br-rich nanowires, which effectively enhance phonon scattering. As a result, we achieve a peak figure of merit of ZT ~1.41 at 823 K, with an average figure of merit of ~0.42 over the temperature range of 323–823 K. This work provides a universal paradigm for decoupling electron-phonon interactions in thermoelectric materials, offering new insights for the optimization of thermoelectric performance.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509049
This study systematically compared three virus enrichment and concentration methods—polyethylene glycol (PEG) precipitation, aluminum salt coagulation, and centrifugal ultrafiltration—for detecting SARS-CoV-2 in high-turbidity, high-strength wastewater from inbound flights. The aluminum salt coagulation method exhibited the best overall performance, achieving an average recovery rate of 25.95% for SARS-CoV-2 pseudovirus, significantly higher than PEG precipitation (12.91%) and centrifugal ultrafiltration (0.22%) (P<0.05). Its detection limit reached 10 copies·mL⁻¹, whereas centrifugal ultrafiltration suffered severe membrane fouling, limiting detection to 1,000 copies·mL⁻¹. Considering the high pH buffering of flight wastewater, the aluminum salt method was optimized by adjusting pH to 6.00±0.4, employing rapid magnetic stirring, and reducing mixing time to 1 minute, yielding an average recovery of 27.56% (not significantly different from the original 25.95%, P>0.05). An automated enrichment device was developed based on the optimized method, reducing processing time per sample from 115 min to 60 min while maintaining comparable recovery and improved repeatability. Applied to 1,309 wastewater samples from inbound flights between January 2024 and May 2025, the average detection rate of SARS-CoV-2 was 45.45%, with trends consistent with national COVID-19 epidemiological data. The automated device demonstrates suitability for routine surveillance, providing technical support for port epidemic prevention.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030602
In the context of accelerated urbanization, regional air composite pollution in medium and large urban agglomerations is primarily characterized by PM2.5-O3 compound pollution. To elucidate the meteorological causes of PM2.5-O3 compound pollution in the Yangtze River Delta (YRD) region over the recent seven years (2017–2023), this study analyzed monitoring data from typical cities (Nanjing, Shanghai, Hangzhou, and Hefei) using Pearson and partial correlation coefficients. Results indicate: (1) PM2.5 pollution exhibited a significant downward trend across all four cities, with notable improvement during the COVID-19 pandemic in 2020, underscoring the effectiveness of air pollution control measures. Conversely, O3 pollution remained elevated or increased in some cities, indicating persistent challenges in O3 control. (2) During O3 pollution episodes, PM2.5 and O3 concentrations were positively correlated, whereas during PM2.5 pollution episodes, they were negatively correlated. (3) Compound pollution days were predominantly observed from February to October, with the highest frequency (20 days) occurring from April to June. (4) The significant reduction in PM2.5 weakened the aerosol 'umbrella effect', enhancing surface radiation and promoting near-surface O3 formation. Concurrently, changes in the NOx/VOCs ratio weakened O3 titration, and climate warming accelerated O3 precursor generation and potentially altered boundary layer structure, collectively contributing to O3 accumulation in the cold season and an increasing frequency of compound pollution during that period. (5) The formation mechanisms of PM2.5 and O3 are driven by distinct meteorological conditions, with low overall concentration correlation; however, under compound meteorological conditions such as high temperature, stagnant air, and weak diffusion, both pollutants tend to rise synchronously, indicating that compound pollution events are typically driven by multiple adverse meteorological factors. This study demonstrates that from 2017 to 2023, PM2.5 pollution significantly decreased while O3 pollution showed an increasing trend. Compound pollution was concentrated in April–June and influenced by high temperature, stagnant air, and weak diffusion. With effective PM2.5 control, enhanced surface radiation and changes in O3 precursors led to O3 accumulation in the cold season, increasing compound pollution frequency. Overall, compound pollution is driven by multiple meteorological factors, posing complex challenges for control.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021901
To assess the impact of the Air Pollution Prevention and Control Action Plan (APPCAP) on the chemical composition of PM2.5, this study analyzed the concentrations, existing forms, and sources of water-soluble ions in PM2.5 collected during summer (June–August) in the northern suburbs of Nanjing for the years 2012, 2013, 2017, and 2019. The results demonstrate a significant reduction in total water-soluble ion concentrations in 2017–2019 compared to 2012, indicating the effectiveness of APPCAP in mitigating PM2.5 pollution. Sulfate (SO4^2−), nitrate (NO3^−), and ammonium (NH4^+) (collectively SNA) were the dominant ionic species, contributing 69.98%–92.58% of the total ion mass, with SO4^2− being the most abundant. In the summers of 2013 and 2017, PM2.5 exhibited alkaline properties, and SNA primarily existed as NH4NO3 and (NH4)2SO4. Conversely, in 2019, PM2.5 became acidic, with SNA present as NH4NO3 and NH4HSO4. The nitrogen oxidation ratio (NOR) and sulfur oxidation ratio (SOR) indicated that NO3^− and SO4^2− predominantly originated from secondary reactions, with SO2 undergoing secondary conversion more readily than NO2, and the degree of secondary conversion increasing annually. Source apportionment revealed a shift from long-range transport in 2013 to local and regional sources by 2017. These findings underscore the success of APPCAP in reducing primary emissions and altering the chemical speciation of secondary inorganic aerosols, while highlighting the persistent dominance of sulfate and the need for continued SO2 emission controls.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60678-0
Improper disposal of plastic waste represents both the loss of valuable resources and significant environmental threat. This study investigates the thermal liquefaction of high-density polyethylene (HDPE) using low-pressure superheated methanol. It systematically evaluates the effects of reaction temperature and the ratio of reactant to methanol on liquefaction efficiency and product characteristics. Results indicate that complete conversion of HDPE can be achieved in low-pressure superheated methanol (<0.5 MPa) at a minimum external heating temperature of 260 °C. Under this condition, oil yield reached 77.1% with alkanes comprising 62.3% of the product alongside minor oxygenated compounds. As temperature increased, the average carbon number of hydrocarbons gradually decreased. Below 260 °C, HDPE conversion decreased significantly, and products were primarily waxy. At 290 °C, the proportion of gasoline-like fractions (C6–C12) increased markedly from 16.6% to 80.9%. Furthermore, reactant ratio plays a critical regulatory role; extremes in ratio—either too high or too low—diminish heat transfer efficiency and reduce conversion. Mechanistically, liquefaction primarily involved cleavage of secondary C−C bonds, where resulting oligomers further cracked into free radicals to form diverse hydrocarbons through secondary reactions. This work demonstrates that low-pressure superheated methanol liquefaction is a mild, efficient, and pretreatment-free method to upcycle polyethylene into valuable fuels. Optimizing these process parameters can pave the way for industrial application, aiding in both plastic pollution management and sustainable resource recovery.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3510-0
The activity and stability of single-atom catalysts (SACs) are intimately associated with the structure of supports. Herein, by employing a van der Waals (vdW) heterostructure support, we construct a highly active and durable Pt SAC for hydrogen evolution reaction (HER). The unique support consists of monolayer MoS2 attaching on hierarchical N-doped carbon nanocages (hNCNC), on which Pt presents as individual single atoms on the hNCNC and as island-like single-atom layers on the MoS2. The optimized Pt1-MoS2/hNCNC demonstrates low overpotential (11 mV at 10 mA cm−2) and high mass activity (5.6 A mgPt−1 at −20 mV) in 0.5 M H2SO4 solution, outperforming commercial Pt/C. Impressively, the Pt1-MoS2/hNCNC exhibits improved long-term stability in proton exchange membrane water electrolyzer relative to commercial Pt/C. The excellent HER performance is attributed to the regulated electronic structure, robust interaction of Pt atoms with MoS2/hNCNC and facilitated charge transfer. This study establishes an innovative strategy to develop a highly active and durable Pt SAC using vdW heterostructure supports.