SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3760-y
Layered chalcogenide compounds have attracted considerable attention for optoelectronic applications due to their rich structural diversity and unique physical properties, including high carrier mobility, ferromagnetism, ferroelectricity, and outstanding optoelectronic and thermoelectric performance. Their tunable bandgaps and strong light absorption render them highly suitable for next-generation photodetectors. However, the environmental instability of many 2D chalcogenides poses a critical challenge for practical applications. In this work, we report a high-performance, polarization-sensitive photodetector based on an air-stable ternary chalcogenide FeIn2Se4. Angle-resolved polarized Raman spectroscopy reveals that the four characteristic Raman modes exhibit a 60° periodic variation in intensity, highlighting the material's pronounced in-plane anisotropy. Benefiting from its strong absorption over a broad spectral range (510–1028 nm), the FeIn2Se4-based device demonstrates reliable photoresponse under multiple excitation wavelengths (405, 473, 515, and 638 nm), showcasing its wideband detection capabilities. Furthermore, XPS measurements after prolonged air exposure confirm the enhanced chemical stability of FeIn2Se4 compared to binary chalcogenides. These findings demonstrate that 2D ternary FeIn2Se4 is an excellent candidate for advanced anisotropic optoelectronic devices, offering broadband photodetection, robust polarization sensitivity, and excellent environmental resilience.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3633-5
High-temperature interfacial diffusion in Half-Heusler (HH) thermoelectric devices poses significant challenges for practical applications, particularly the diffusion of Ag from conventional solders, which degrades material performance and device stability. This study reveals anomalous Ag diffusion through a Cr powder barrier layer into Ti0.5Zr0.5NiSn0.98Sb0.02, driven by Sn phase penetration. In contrast, employing a Cr foil barrier layer pre-densified the material, effectively preventing Sn phase penetration and eliminating Ag diffusion pathways, thereby preserving junction integrity. After aging at 973 K for 30 days, the Cr foil junction maintained a clean interface with a low contact resistivity of 0.27 μΩ cm2. Benefiting from this interfacial design, a Hf-free HH module achieved a high conversion efficiency of 10.4% at a hot-side temperature of 976 K, alongside long-term stability. This work addresses critical bottlenecks in developing high-performance, low-cost HH modules, facilitating their commercial application in waste heat recovery.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605014
Chlorinated aliphatic hydrocarbons (CAHs) are prevalent groundwater contaminants at industrial sites in China. This pilot-scale study evaluated in-situ anaerobic bioremediation of CAHs-contaminated groundwater in a low-permeability bedrock fracture zone at depths up to 40 m. A self-developed anaerobic dechlorinating culture (BS-1), containing Dehalococcoides, Desulfitobacterium, and Dehalogenimonas, was injected alongside carbon sources (sodium citrate and emulsified vegetable oil) and nutrients. Pressurized nitrogen gas injection enhanced the distribution of amendments, achieving a radius of influence of 5.0 m. Over 399 days of monitoring, the combined use of slow-release and soluble carbon sources maintained anaerobic conditions (ORP < -100 mV) for over one year, providing sustained electron donors. The emulsified vegetable oil reduced injection frequency and operational costs. The BS-1 culture effectively dechlorinated vinyl chloride, cis-1,2-dichloroethylene, trichloroethylene, and chloroform, achieving removal efficiencies exceeding 95%. At times, groundwater quality met the Class IV standard of GB/T 14848-2017. This study demonstrates a green, economical, and effective solution for CAH-contaminated site remediation, with significant engineering application potential.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3774-3
Lithium-air capacitor batteries (LACBs) integrate the rapid charge-discharge capability of supercapacitors into conventional lithium-oxygen batteries, significantly enhancing power density. However, their cycling stability remains unsatisfactory. In this study, we incorporated redox mediators (RMs) into an LACB featuring a dual-cathode configuration. This design facilitates sustained electron transfer between the electrode and Li2O2/Oxygen, thereby delaying RM deactivation caused by electrode passivation and improving overall electrochemical performance. The RM-enhanced battery achieved over 250 cycles at 2 mA cm−2 with a limited capacity of 0.5 mAh cm−2, while exhibiting a 0.54 V reduction in charging voltage at 0.1 mA cm−2 compared to the RM-free system. Furthermore, application of an aluminum foil sealing technique enabled a power density of 13.8 mW cm−2 at 6 mA cm−2, overcoming mass transport limitations inherent in open-cell configurations. We also investigated the influence of oxygen barrier films with varying barrier capabilities on LACB performance. Results indicate that films with superior oxygen resistance better maintain a clean capacitor electrode surface, thereby providing more stable electron supply to the RMs and enhancing rate capability and cycling performance. These findings underscore the potential of redox mediators in improving the performance and longevity of LACBs, offering a promising strategy for their future development.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3859-y
Photocatalytic CO2 reduction is an attractive route to address sustainable energy crises and environmental issues, yet its efficiency is limited by poor charge separation, narrow light absorption, sluggish kinetics, and low CO2 adsorption/activation. Here, a series of Co SA-TT-COF/CdS S-scheme heterojunction photocatalysts were synthesized by integrating Co single atoms (Co SA) decorated covalent organic frameworks (COFs) with CdS nanotubes via in situ condensation and post-modification. The TT-COF layer thickness on CdS was regulated to optimize active site density and accessibility. The optimal Co SA-TT-COF/15 wt% CdS heterojunction, with a TT-COF thickness of 50.5 nm, achieved a CO production rate of 14157 μmol g−1 h−1 and a selectivity of 90.9%, among the best COF-based photocatalysts reported. Theoretical calculations, experiments, and femtosecond transient absorption spectroscopy revealed that the S-scheme heterojunction enhances the built-in electric field, optimizes energy levels, narrows bandgaps, extends light harvesting, improves charge separation and transfer kinetics, and lowers energy barriers for CO2 adsorption/activation, directly contributing to superior performance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040708
Bisphenol S (BPS), a substitute for bisphenol A (BPA), is widely used in food packaging, plastics, and dental fillings. BPS enters and accumulates in the human body via respiratory, digestive, and dermal routes, posing increasing health risks. Epidemiological and animal studies link BPS exposure to metabolic disorders. This review systematically summarizes BPS pollution status and its mechanisms in obesity, non-alcoholic fatty liver disease, diabetes, cardiovascular diseases, and immune system disorders. BPS detection rates reach 78.5% in food samples (up to 67.1 μg·kg−1) and 81.67% in fish (up to 65.31 μg·kg−1). In indoor dust, BPS levels reach 26.6 μg·g−1, with adult daily exposure estimated at 0.78 ng·kg−1 in China. Mechanistically, BPS disrupts lipid and glucose metabolism, induces oxidative stress and inflammation, and alters nuclear receptor signaling. The review highlights the need for molecular target identification and metabolic network interaction studies to develop intervention strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4274-x
The escalating power density of electronic devices necessitates effective visible-light shielding in advanced packaging to ensure circuit security and long-term reliability. Photosensitive polyimides (PSPI) serve dual roles as photodefinable dielectrics and structural layers, but intrinsically black PSPI (B-PSPI) suffer from competitive ultraviolet (UV) absorption between chromophores and photosensitive moieties, limiting co-optimization of deep visible-light blocking and lithographic resolution. Here, we report a main-/side-chain spatial decoupling strategy to synthesize a novel B-PSPI. By polymerizing pyromellitic dianhydride with a main-chain coloring monomer (4,4'-diaminodiphenylamine) and a side-chain photosensitive monomer (1,4-dihydropyridine-functionalized diamine), the monomer stoichiometric ratio is precisely engineered. This design spatially isolates functional groups and enhances charge transfer, yielding exceptional visible-light shielding (CIE L* index of 21.39, cut-off wavelength ≈ 555 nm) with good lithographic sensitivity. UV exposure triggers in situ generation of coordination sites from photosensitive groups, anchoring active metal species for electroless copper plating. This enables direct additive fabrication of fine copper lines (40/80 μm line width/spacing) with robust Cu/B-PSPI interfacial adhesion of 16.6 MPa. This work provides a robust molecular design paradigm for B-PSPI, integrating superior optical shielding and surface metallization for high-density interconnect applications.