SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4351-8
Breaking intrinsic structural symmetry is a fundamental prerequisite for pronounced nonlinear optical responses. Low-symmetry semiconductors with inherent anisotropy enable self-powered optoelectronic conversion and polarization-sensitive functionalities. This work reports the synthesis of low-dimensional van der Waals chain TeSe2 crystals with intrinsic inversion and C3 symmetry breaking. Angle-resolved polarized Raman spectroscopy and second-harmonic generation measurements confirm crystalline anisotropy and nonlinear optical performance. Electrical transport studies reveal p-type conduction with a room-temperature field-effect mobility of 122 cm2 V-1 s-1. The TeSe2 photodetector achieves self-powered detection and linearly polarized light detection across 405–1064 nm, with a photoresponsivity of 77.3 mA/W at 532 nm. The linear photogalvanic effect response is effectively modulated by gate voltage. Density functional theory calculations attribute p-type doping to Te and Se vacancies, while the nonlinear optical origin is linked to strong Berry curvature. Applications in polarization encoding communication and polarization imaging are demonstrated, indicating potential for low-energy-consuming, highly sensitive, on-chip integrated linear polarized photodetectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4239-2
The sluggish kinetics of the oxygen evolution reaction (OER) remains a bottleneck for efficient water splitting. NiFe-layered double hydroxides (LDHs) are promising OER catalysts, but their performance is often limited by the high-spin state of Fe3+ and poor structural stability. Here, we report a series of amino acid-intercalated iron-rich NiFe-LDHs (AA-NiFe-LDHs) synthesized via a facile one-step coprecipitation method. Intercalation of glycine, alanine, and valine into the interlayer galleries expands the interlayer spacing and induces a partial transition of Fe3+ from high-spin to low-spin state, as confirmed by X-ray absorption spectroscopy and Mössbauer spectroscopy. The low-spin Fe3+ enhances the intrinsic catalytic activity by optimizing the adsorption energy of oxygen intermediates. Among the series, the glycine-intercalated sample (Gly-NiFe-LDH) exhibits the best OER performance in 1.0 M KOH, with an overpotential of 240 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, significantly outperforming the pristine NiFe-LDH (280 mV, 52 mV dec−1). Moreover, Gly-NiFe-LDH shows excellent long-term stability, retaining 95% of its initial activity after 24 h of chronopotentiometry at 10 mA cm−2. The intercalation also increases the electrochemically active surface area by 2.3-fold and reduces the charge transfer resistance from 12.5 Ω to 4.8 Ω. This work demonstrates that amino acid intercalation is an effective strategy to modulate the spin state of Fe3+ and enhance the OER performance of NiFe-LDHs, providing a new avenue for designing high-efficiency, low-cost electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4359-0
Organic solar cells (OSCs) require cathode interlayers (CILs) that combine high charge transport, defect passivation, and thickness insensitivity for scalable manufacturing. Here, we report the synthesis of a novel A-D-A-A'-type polymer, PDPP2F-NDI-N, via the green and efficient direct arylation polymerization (DArP) method. The multiple electron-deficient units in the backbone confer strong electron-withdrawing character, effective work function modulation, enhanced built-in potential, high crystallinity, and ordered molecular packing. PDPP2F-NDI-N exhibits a high electron mobility of 1.01 × 10⁻³ cm² V⁻¹ s⁻¹ and electrical conductivity of 3.13 × 10⁻³ S m⁻¹, facilitating efficient charge extraction and transport. Its interfacial modification capability suppresses interfacial defects and reduces non-radiative recombination losses. In ternary OSCs, PDPP2F-NDI-N achieves a high power conversion efficiency (PCE) of 20.44%, with outstanding thickness insensitivity retaining 92.8% of peak PCE at a 30 nm CIL thickness, and a T80 lifetime exceeding 1700 hours under photo-thermal aging. This work demonstrates that poly(A-D-A-alt-A') backbone design combined with DArP synthesis provides an effective strategy for developing high-performance, thickness-insensitive, and stable polymeric CILs, advancing efficient, stable, and scalable OSC applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022801
Paddy soils are a major source of agricultural methane (CH4) emissions. Biochar is widely applied to paddy soils, while dissolved organic matter (DOM) is ubiquitous; both can regulate CH4 emissions by mediating electron transfer processes, yet their synergistic mechanisms remain unclear. This study investigated the individual and combined effects of biochar and the DOM model compound anthraquinone-2,6-disulfonic acid (AQDS) on CH4 emissions from paddy soil during incubation. Biochar amendment increased DOM concentration and accelerated extracellular electron transfer, resulting in a maximum cumulative CH4 emission of (66.23±16.20) μmol, four-fold higher than the control (15.14±0.18) μmol. In contrast, AQDS addition markedly suppressed CH4 accumulation to (1.04±0.09) μmol, attributed to sulfate introduction as a competitive electron acceptor, despite enhanced electron exchange. The combined biochar-AQDS treatment yielded intermediate CH4 accumulation of (12.71±0.32) μmol. Although DOM availability increased, sulfate-driven electron competition inhibited methanogens, and the combined treatment favored the acetoclastic methanogenesis pathway, which produces less CH4 per unit acetate, resulting in lower emissions than biochar alone but higher than AQDS alone, indicating an additive effect. These findings elucidate the mechanisms by which biochar and DOM jointly regulate CH4 emissions from paddy soils, providing a theoretical basis for agricultural management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3900-8
Memristors, which leverage ion migration for resistance switching, offer breakthroughs in bionic perception, information security, and edge computing but face bottlenecks in functional integration and stability. Herein, we explore all-inorganic Cu3SbI6 nanocrystals (NCs) & PMMA composite memristors (Ag/PMMA&Cu3SbI6/ITO) regulated by NCs doping (0–15 wt%). The devices operate via electric field-induced Ag+ ion migration and conductive filament dynamics, where NCs act as local electric field enhancers. At a doping concentration of 4 wt%, stable bipolar switching (Ron/Roff > 2 × 10^3, cycling endurance > 700 cycles) enables the simulation of biological nociception/Pavlovian reflexes and the construction of basic logic gates. At 2 wt%, sparse NCs induce random filament formation for encryption key extraction, which integrates with 4 wt% logic gates to enable efficient encryption/decryption of text/image data. This work provides a strategy for designing multifunctional memristors by regulating ion transport through nanocrystal concentration, offering references for related functional integration and cross-disciplinary applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510072
Porous structures are widely used in hydraulic and pneumatic systems for flow rectification and throttling, reducing velocity, regulating pressure, and improving flow stability. Numerical simulation is a common approach to study such flows, yet the lack of standardized parameter settings often leads to user-dependent errors. This study, based on the CFD software Fluent, systematically analyzes nine key parameters across three core stages: modeling, mesh generation, and solver settings. Under both quasi-2D and 3D configurations, the influence and underlying mechanisms of each parameter on simulation results are revealed, and a reference parameter-setting method is proposed. The method is validated against wind tunnel experiments, showing that the simulated average velocity reduction ratio γS deviates from experimental values by less than 6%, confirming its reliability and applicability. This work provides a basis for standardized parameter settings in numerical simulations of porous structures, enhancing consistency and predictive accuracy.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607019
This study investigated the effects of biochar on volatile fatty acids (VFAs) production, biogas composition, physicochemical properties of the fermentation broth, and microbial community structure through batch anaerobic fermentation experiments using food waste as the substrate. The results demonstrated that the addition of biochar (1 g/L) significantly enhanced VFAs production, with the total VFAs concentration reaching 2150 mg/L in the biochar group, which was 30.2% higher than that of the control group (1651 mg/L). Acetic acid, propionic acid, and butyric acid were identified as the primary VFAs components. In the fermentation system, biochar exhibited a notable pH-buffering effect, stabilizing the fermentation environment. Additionally, its porous structure adsorbed ions during the fermentation process, resulting in a slightly lower electrical conductivity compared to the control group. Microbial community analysis revealed that biochar addition enriched key acidogenic bacteria, such as Defluviitoga and norank_f__Family_XI, optimizing the microbial community structure, and thereby facilitating organic acid production. In summary, biochar effectively promoted the efficient accumulation of VFAs during anaerobic fermentation of food waste by improving the fermentation microenvironment, enhancing system buffering capacity, and regulating microbial community composition. These findings provide theoretical support for sustainable enhancement of resource utilization of food waste.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3924-x
Metal halide perovskite solar cells (PSCs) have achieved power conversion efficiencies exceeding 27%, rivaling crystalline silicon photovoltaics. Among device architectures, the inverted p-i-n configuration offers excellent reproducibility, negligible hysteresis, and compatibility with silicon bottom cells, making it promising for scalable tandem integration. As the field shifts toward industrial viability, key challenges focus on interfacial stability, process reproducibility, and large-area manufacturability. The buried interface between the perovskite absorber and charge transport layers dictates nucleation, crystallization, charge extraction, and recombination dynamics. Imperfect interfacial contact or mismatched energy alignment leads to trap states, increased nonradiative recombination, and rapid degradation. Self-assembled monolayers (SAMs) have revolutionized interface control, offering tunable energy levels, minimized parasitic absorption, and reduced defects. However, SAM-based interfaces face scale-up challenges due to molecular aggregation, incomplete coverage, and hydrophobicity, causing nonuniform nucleation and pinhole formation. Co-assembled monolayers (Co-SAMs) have been explored but remain limited to small areas. Addressing this bottleneck, Zhao et al. proposed a 'SAM-in-matrix' strategy embedding SAM molecules within a tris(pentafluorophenyl)borane (BCF) matrix. This BCF framework disrupts π–π stacking, suppressing aggregation and producing an amorphous, uniform, and highly wettable hole transport layer, potentially enabling scalable manufacturing.