SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4281-7
Multispectral camouflage materials must simultaneously address visible and infrared (IR) detection while maintaining environmental stability and mechanical flexibility for deployment in harsh conditions. This work presents a multilayer composite integrating a colorful, IR-transparent visible reflection (VR) layer, a low-emissivity graphene (LEG) layer, and an aramid nanofiber (ANF) aerogel layer. The VR layer provides tunable visible colors without compromising the low-emissivity property of the LEG layer, which achieves IR emissivity between 0.30 and 0.43. The ANF aerogel, reinforced with a grid structure, reduces thermal conduction, lowering IR radiation intensity by 40% at an 80 °C heat source. The composite exhibits effective electromagnetic interference (EMI) shielding and maintains multifunctional stability in strong acid, strong alkali, saline, and organic media. This design offers a novel strategy for environmentally robust multispectral camouflage materials suitable for extreme operational environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4204-4
Heterodimensional superlattices, integrating materials of different dimensionalities (e.g., 0D, 1D, 2D) within a periodic structure, have attracted significant attention due to their unique electronic structures and emergent properties arising from inter-dimensional coupling. This review comprehensively summarizes the state-of-the-art preparation strategies, distinctive physical properties, and diverse applications of these emerging systems. Beyond conventional epitaxial growth and chemical intercalation methods, recent advances include van der Waals assembly and phase engineering, enabling precise control over layer stacking and interfacial interactions. Key properties discussed include tunable electronic band structures, enhanced spin-orbit coupling, and emergent phenomena such as the in-plane Hall effect, which are promising for spintronic devices. The review also highlights applications in energy storage and conversion, where heterodimensional superlattices exhibit improved ion transport and catalytic activity. Challenges remain in scalable fabrication and structural stability, but the field holds potential for next-generation electronics and energy technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4236-8
Electrochemical nitrate reduction (NO3RR) to ammonia offers a sustainable route for nitrogen recovery from wastewater, yet its efficiency is constrained by complex multi-step proton-electron transfers and competitive hydrogen evolution. Here, we report a series of binary cobalt-copper phosphates with precisely tuned Co/Cu ratios, revealing a volcano-type relationship between composition and catalytic activity. The optimized Co0.5Cu1.5(OH)PO4 catalyst, supported on a Ni3Co1OxHy/Ni foam substrate, achieves a Faradaic efficiency of 99.0% for ammonia at a high current density of 200 mA cm−2 in 1 M nitrate electrolyte, with a production rate of 9.18 mg h−1 cm−2 and sustained stability over 200 hours. In-situ ATR-FTIR spectroscopy and density functional theory calculations elucidate a tandem mechanism: Co sites promote water dissociation to generate active hydrogen (H*), while adjacent Cu sites facilitate nitrate adsorption and subsequent hydrogenation steps. This synergistic division of labor lowers the energy barrier for the rate-determining step, effectively suppressing HER and enhancing intrinsic kinetics. The work demonstrates that precise atomic-ratio engineering in dual-site transition metal phosphates provides a viable strategy to overcome activity-selectivity trade-offs in electrocatalytic nitrate-to-ammonia conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3691-9
Near-infrared (NIR) spectroscopy has significantly advanced NIR light sources, yet creating NIR emitters with optimal luminescence properties, high thermal stability, and adjustable emission peaks remains a critical challenge for future smart NIR devices. Here, we introduce a chemical unit cosubstitution strategy by incorporating Ca2+ and Sn4+ ions into the garnet structure. Through this approach, Y3−yCayGa4.95−ySnyO12:0.05Cr3+ (y = 0–1) phosphors were developed by modulating the A&C ligands, resulting in emission centers ranging from 708 to 768 nm. The modified local environment of Cr3+ accounts for the increased light intensity (2.71 times) and broadening observed. Furthermore, this study investigated the impact of varying Cr3+ concentrations (Y2.6Ca0.4Ga4.6−xSn0.4O12:xCr3+) on the production of high-performance phosphors. Compared with Y3Ga4.93O12:0.07Cr3+, the optimized phosphor exhibited exceptional external quantum efficiency (EQE = 34.96%). The luminescence enhancement is attributed to an increase in radiative transitions caused by octahedral Jahn-Teller distortion, whereas the notable thermal stability (91.3% at 423 K) is attributed to the presence of weak electron-phonon coupling (EPC) and oxygen vacancy (OV) defects. Finally, by combining it with a 450 nm blue LED chip, we constructed a near-infrared phosphor-converted LED (NIR pc-LED) device with superior electroluminescence efficiency (18.8% @ 100 mA), increasing the ultralow quenching rate (< 5% intensity loss after 30 days of operation) and demonstrating remarkable performance in plant lighting applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3700-7
Photocatalytic synthesis has been considered a promising technology for solar-to-chemicals conversion. Here, a series of novel photocatalysts was synthesized by decorating uranyl sites on imine-based covalent organic frameworks (i-COF) and proved functioning for the uniformly boosted H2O2 production by 1.6–10.1 folds compared with the bare i-COFs in a wide pH range from 2 to 11. Typically, an optimal H2O2 production rate of 1435.9 μmol g−1 h−1, i.e., 28.72 mmol g(U)−1 h−1, was realized over uranyl decorated TTa-COFs under visible light. Systematic investigations reveal that the universally and remarkably promoted performance is attributed to the outstanding electron-transfer ability, accelerated activation of molecular oxygen and favored formation of ·O2− and *OOH as the key intermediate by virtue of the decorated uranyl ions; thus the two-step single-electron oxygen reduction reaction (ORR) for H2O2 photo-generation is significantly facilitated. This work paves a new way for the uranyl-decorated COFs as a novel photocatalyst and provides in-depth insight to the reaction mechanism for photocatalytic H2O2 production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3693-0
The development of catalysts with highly efficient oxygen evolution performance and low-Ir loading is key to scaling up the application of proton exchange membrane (PEM) water electrolysis technology. Here, an Ir-skin catalyst (Ir@KM) is realized on a potassium-manganese oxide (K0.25MnOx (KM)) using an ion-exchange method. The Ir-skin over the prepared Ir@KM has a low Ir–Ir atomic distance, endowing an energetically favorable oxide path mechanism to allow a low theoretical overpotential of 0.13 V. Ir@KM offers a low overpotential of ~280 mV at a current density of 10 mA cm−2 and provides a high mass activity of up to 18,500 A gIr−1 at a cell voltage of 1.8 V in PEM, which is 17.6 times higher than that of IrO2, demonstrating a significant advantage in reducing the cost of the membrane electrode. The presented Ir-skin concept represents a promising strategy to fabricate low-Ir catalyst with high activity and durability for practical applications of PEM.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3838-5
Air-permeable and ultrathin conductive electrodes are essential for next-generation soft electronics, including breathable wearables, on-skin devices, and bio-integrated electronics. However, conventional metallization strategies, such as sputtering and ink-printing, often suffer from severe vertical charge leakage due to the porous and ultrathin characteristics of nanofibrous networks, leading to device short-circuiting, operational failure, and limited vertical integration. Here, we present a solvent-selective dissolution-assisted transfer printing strategy to achieve surface-confined metallization of ultrathin, lightweight, and gas-permeable nanofibrous networks, enabling lateral conductivity while maintaining vertical insulation. This transfer printing process facilitates not only the rapid formation of conductive patterns on the surface of nanofibrous networks but also mechanical reinforcement through solvent evaporation-induced interlocked fiber-fiber welding. Meanwhile, the strategy preserves the high permeability of the nanofibrous networks and imparts a unique combination of surface conductivity (2 Ω cm) and vertical insulativity (10^11 Ω cm). The resulting anisotropic conductive networks enable low-voltage wearable heaters, high-sensitive pressure sensors, and ultralight temperature sensors. A pressure-temperature dual-modal sensing patch is further fabricated for intelligent grasping classification. The proposed surface-confined metallization strategy enables rapid fabrication of an anisotropic conductive network as a building block to construct air-permeable, ultrathin, and lightweight wearable electronics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024083002
Selenium (Se) is an essential trace element for human health, and dietary intake through Se-rich crops is the primary route. However, total soil Se content does not directly reflect the bioavailability to plants, which depends largely on soil available Se. This study, conducted in Shipai Town, Longshan County, Hunan Province, used 1:50,000 land quality geochemical survey data to investigate factors influencing the Se bioaccumulation coefficient in maize kernels. Soil pH, CaO, and MgO were identified as significantly positively correlated with the bioaccumulation coefficient and were selected as proxies for soil available Se. A random forest (RF) model was developed to predict maize grain Se content and assess the feasibility of cultivating Se-rich maize in low-Se farmland. Results showed that although soil Se was deficient, 53.64% of maize grain samples met the Se-rich product standard (0.02–0.30 mg·kg−1). Compared with multiple linear regression, the RF model exhibited higher accuracy and reliability. The RF model predicted that 40.91% of farmland in the study area is suitable for natural Se-rich maize cultivation, representing a 25.86% increase over the area identified by soil total Se alone. This study provides a novel methodological framework for planting natural Se-rich maize in Se-deficient regions, validating the potential for such cultivation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60631-1
Methane dehydroaromatization (MDA) offers a carbon-neutral route to benzene, toluene, and xylene (BTX), yet the regulatory mechanisms of Brønsted acid site (BAS) strength and spatial proximity to Mo sites remain unresolved. This study systematically tunes BAS strength via isomorphous substitution (Al, Ga, Fe, B) and Mo-BAS proximity in ZSM-5, integrating catalytic evaluations with density functional theory (DFT). Strongly acidic Al-zeolites achieve the highest methane conversion, while weakly acidic B-substituted systems exhibit optimal mono-/bifunctional synergy, outperforming moderate-acid counterparts. DFT reveals that deprotonation energy (DPE) correlates with acid strength; Al-ZSM-5 (DPE = -5.68 eV) lowers the C–H activation barrier (ΔG = 1.467 eV). Spatial proximity analysis shows that nanoscale Mo-BAS distances, achieved via ball milling, enhance methane conversion by 33% and BTX yield by 31% compared to micrometer-scale mixtures, by accelerating intermediate transport and suppressing coke. These findings establish a multi-scale framework linking acid strength, spatial confinement, and electronic modulation, providing actionable guidelines for designing next-generation MDA catalysts.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60629-3
This study reports the synthesis of a novel Z-scheme heterojunction composite film comprising Ag/Bi2MoO6/BiOBr via electrochemical processes, ion-exchange techniques, and subsequent photodeposition of silver nanoparticles. The incorporation of Ag nanoparticles exploits localized surface plasmon resonance (LSPR) effects and serves as an electron mediator, establishing a Schottky barrier that suppresses charge recombination. The optimized 1.5% Ag/Bi2MoO6/BiOBr film achieves a CO production rate of 13.65 μmol/(g·h) from photocatalytic CO2 reduction, significantly outperforming the unmodified Bi2MoO6/BiOBr film. Photocurrent and impedance analyses confirm enhanced charge separation in the Ag-modified composite. A non-linear relationship between Ag loading and photocatalytic efficiency was observed, with optimal performance at 1.5% Ag. The proposed Z-scheme mechanism elucidates the synergistic interactions among components, providing a scientific basis for rational design of advanced photocatalysts and immobilized systems for CO2 reduction. This work offers insights into the development of efficient, sustainable photocatalytic technologies for carbon capture and utilization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025020603
The high cellulase-producing strains were screened and the enzyme production conditions were optimized, providing strain resources for the effective utilization of agricultural solid waste. A promising cellulolytic strain S3 was isolated from the soil of Hengshui Lake Wetland Park. The isolation process employed Congo red plate staining method for primary screening, followed by secondary screening through cellulase activity determination and straw degradation experiments. Through morphological observation and molecular biology identification, the strain S3 was identified to be Bacillus cereus. The ratio of transparent circle to colony diameter of strain S3 was 4.01±0.17. The filter paper enzyme activity of strain S3 was 42.09 U·mL−1, and the degradation rate of corn stover reached 19.29% after 10 days of fermentation. It was found that the optimum carbon source of strain S3 was the mixture of microcrystalline cellulose and wheat bran with the addition amount of 4%, and the optimum nitrogen source was soybean powder with the addition amount of 2%. Single factor experiment and response surface methodology were used to optimize the enzyme production conditions of the strain S3. The optimal conditions were fermentation time of 76 h, fermentation temperature of 36℃, initial pH of 6, and inoculation volume of 4%. Under these conditions, the filter paper enzyme activity reached 60.13 U·mL−1, which was 1.43 times higher than that before optimization. The strain S3 showed the high cellulase-producing capability, demonstrating its potential as an efficient microbial candidate for the degradation and utilization of agricultural solid waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509078
The rapid expansion of photovoltaic (PV) installations and the impending retirement of early-stage modules have made the recycling of end-of-life PV modules an urgent issue. This review systematically examines the types and structures of retired PV modules, with a focus on crystalline silicon (c-Si) and thin-film technologies. It critically evaluates the principles, processes, and pros and cons of physical, chemical, pyrolysis, biological, combined, and emerging methods for recovering c-Si modules. The current status of silicon, metal, and valuable component recovery processes is summarized. For thin-film modules, the core technologies for recovering valuable components via pyrometallurgical, hydrometallurgical, biological, and novel approaches are analyzed in depth. Results indicate that conventional methods (physical, chemical, pyrolysis) remain dominant but suffer from high energy consumption, pollution, and chemical usage. Emerging technologies such as biological and green leaching are identified as key research directions, though they face challenges of low technical maturity and high costs. Finally, policy orientations and existing challenges are discussed, and future development directions are proposed, providing significant guidance for the sustainable and large-scale green development of the PV industry.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0035
Iron-based catalysts in CO2/H2 atmospheres undergo dynamic carburization and oxidation phase transitions, complicating active-phase identification and stability control. This study prepared high-purity single-phase χ-Fe5C2 (Hägg carbide) and θ-Fe3C (cementite) via gas-solid carburization, with purity confirmed by XRD and Mössbauer spectroscopy. Fixed-bed reactor tests (H2/CO2 = 1, 0.1 MPa, 270–420 °C), pulse experiments (270 °C), and in situ XRD (10% CO2/He, 340 °C) were employed to investigate catalytic performance and structural evolution in the reverse water-gas shift (RWGS) reaction. Results show that χ-Fe5C2 exhibits higher RWGS activity but is more susceptible to oxidation, whereas θ-Fe3C demonstrates superior oxidation resistance but lower activity. Under RWGS conditions with H2, θ-Fe3C partially transforms into χ-Fe5C2; however, in 10% CO2 atmosphere, both carbides directly oxidize to Fe3O4 without inter-carbide transformation. In situ XRD at 340 °C and 0.1 MPa revealed that χ-Fe5C2 fully oxidizes within 11 h, while θ-Fe3C retains residual phase after 18.3 h, confirming its higher oxidation stability. These findings elucidate the atmosphere-dependent evolution mechanisms of χ-Fe5C2 and θ-Fe3C, providing experimental basis for phase-structure regulation and operational stability optimization in iron-based Fischer-Tropsch and RWGS catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025100102
Per- and polyfluoroalkyl substances (PFAS) are emerging contaminants of concern in China, and drinking water is a major exposure pathway. This study investigated 17 PFAS in surface water from 12 drinking water sources along the Hubei section of the Yangtze River mainstream during dry, normal, and wet seasons. Total PFAS concentrations ranged from 10.84 to 41.05 ng/L (dry), nd to 62.60 ng/L (normal), and 6.77 to 29.00 ng/L (wet). Predominant compounds were PFBS, PFOA, PFHxA, PFBA, and PFOS. Lake-type sources exhibited significantly higher concentrations than river-type sources, and dry and normal seasons showed higher levels than wet season. Compared to other Chinese sources, PFAS levels in Hubei were moderate, with fluorochemical plant inputs and population density as likely influencing factors. Ecological and health risk assessments indicated acceptable risks. In four selected water supply systems, PFAS distribution from source to tap was examined; PFOA, PFBA, PFHxA, and PFBS were dominant, and secondary water supply did not significantly introduce or remove PFAS. Health risks from tap water were within acceptable limits.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606006
Chitosan-based microsphere composites have attracted considerable attention for phosphorus adsorption due to their facile preparation, low cost, environmental friendliness, and high uptake capacity. This review summarizes the physicochemical properties and preparation methods of chitosan microspheres for phosphate removal, outlines common modification strategies to enhance adsorption capacity, and discusses their applications in aqueous environments. Adsorption mechanisms, regeneration, and resource recovery of spent microspheres are analyzed. Challenges and recommendations are proposed, including streamlined preparation, enhanced phosphorus recovery, removal of multiple phosphorus forms, and practical implementation. The review aims to guide the development of high-performance chitosan-based microspheres for phosphorus removal.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3963-5
Metal additive manufacturing (MAM) enables integrated one-piece fabrication of parts, high material utilization efficiency, and unparalleled design freedom. However, problems such as low production efficiency, difficulties in ensuring quality stability and defect control limit the large-scale industrial application of AM. In-situ active modulation for AM enables dynamic regulation of parts during the fabrication process, thereby enhancing the quality of the final fabricated parts without introducing extra processing steps. In-situ active regulation enables direct intervention during defect nucleation, providing better effectiveness than post-printing repairs while avoiding performance degradation risks associated with post-processing. Based on the difference of core factors directly affected during regulation, in-situ active regulation is categorized into the following. (1) Process and path parameter optimization, where regulation directly impacts manufacturing-related procedural rules. It is the simplest method of control and the preferred approach, with widespread attention focused on its effects on microstructure and mechanical properties. (2) Laser beam shaping, where regulation directly influences the energy carrier morphology. To address issues such as edge over-melting and localized energy deficiency caused by non-uniform energy distribution, laser beam shaping should be employed. (3) Additional physical field modulation achieved by superimposing supplementary physical fields. When optimal process and path parameters still fail to obtain the desired microstructure and mechanical properties, additional physical field control may be considered. Meanwhile, this work summarized the effects of different additional physical fields on the mechanical properties of various metallic base materials. The future trends of in-situ modulation in additive manufacturing are also discussed.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3820-5
Two novel N-heterocyclic carbene (NHC)-based ligands featuring rigid boron-oxygen (BO) fused-ring units, named Bpmi and Bpmb, and the two corresponding homoleptic meridianal iridium complexes, namely mer-Ir(Bpmi)3 and mer-Ir(Bpmb)3, were designed and synthesized. Single-crystal structures revealed a meridional coordination geometry for both complexes. Shorter Ir–C carbene bond lengths and rigid planar BO-fused ring units contribute to enhanced stability. Both complexes exhibit efficient green phosphorescence (λem = 536/521 nm in toluene, ΦPL > 78%) with short lifetimes (τ = 846/1083 ns), leading to high radiative rate constants (Kr = 10.04 × 10^5 and 7.29 × 10^5 s−1, respectively). Theoretical calculations indicate significantly increased metal-to-ligand charge transfer (MLCT) character (21.69% for mer-Ir(Bpmi)3; 17.30% for mer-Ir(Bpmb)3) compared to reference complexes (13.01% for mer-Ir(pmi)3; 15.99% for mer-Ir(pmb)3). Both complexes exhibit exceptional thermal stability with decomposition temperatures of 491°C (mer-Ir(Bpmi)3) and 540°C (mer-Ir(Bpmb)3). OLED devices using mer-Ir(Bpmb)3 and mer-Ir(Bpmi)3 as emitters demonstrate maximum external quantum efficiencies of 20.0% and 15.6%, respectively. This research pioneers boron-fused ring-containing NHCs and their phosphorescent iridium(III) complexes, establishing a novel design strategy for high-performance NHC-based OLED phosphorescent emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3810-y
Amorphous metal-organic frameworks (aMOFs), with abundant defects and unsaturated coordination sites, are ideal precursors for investigating electrocatalytic reconstruction mechanisms. However, systematic understanding of how different modulation strategies affect reconstruction pathways and final active species remains lacking. Here, an amorphous MOF constructed from 3,4,9,10-pyrene-tetracarboxylic acid (PTA) serves as a controllable precursor to compare doping and alloying effects on structural reconstruction and oxygen evolution reaction (OER) performance. Doping promotes preferential reconstruction into Fe-rich (oxy)hydroxides with more exposed active sites, whereas alloying yields Fe-Co mixed (oxy)hydroxides with limited site exposure. The doped system FeCo0.05-PTA exhibits outstanding OER activity in alkaline conditions, with overpotentials of 208 and 248 mV at 50 and 100 mA cm−2, respectively, and a low Tafel slope of 36.2 mV dec−1. In situ Fourier transform infrared spectroscopy (FTIR) captures the OOH* intermediate, confirming the adsorbate evolution mechanism. Density functional theory (DFT) calculations show the doped system has the lowest free-energy barrier (ΔG = 0.59 eV) at the rate-determining step. This study underscores the decisive role of precursor design, elucidates distinct effects of doping and alloying on reconstruction pathways and final properties of amorphous MOF-derived (oxy)hydroxides, and provides insights for designing related electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3859-y
Photocatalytic CO2 reduction is an attractive route to address sustainable energy crises and environmental issues, yet its efficiency is limited by poor charge separation, narrow light absorption, sluggish kinetics, and low CO2 adsorption/activation. Here, a series of Co SA-TT-COF/CdS S-scheme heterojunction photocatalysts were synthesized by integrating Co single atoms (Co SA) decorated covalent organic frameworks (COFs) with CdS nanotubes via in situ condensation and post-modification. The TT-COF layer thickness on CdS was regulated to optimize active site density and accessibility. The optimal Co SA-TT-COF/15 wt% CdS heterojunction, with a TT-COF thickness of 50.5 nm, achieved a CO production rate of 14157 μmol g−1 h−1 and a selectivity of 90.9%, among the best COF-based photocatalysts reported. Theoretical calculations, experiments, and femtosecond transient absorption spectroscopy revealed that the S-scheme heterojunction enhances the built-in electric field, optimizes energy levels, narrows bandgaps, extends light harvesting, improves charge separation and transfer kinetics, and lowers energy barriers for CO2 adsorption/activation, directly contributing to superior performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3862-x
Hexagonal boron nitride (hBN) is indispensable for next-generation electronics and quantum technologies, yet controlled synthesis of isotopically engineered hBN with macroscopic scalability and atomic-level precision remains challenging. Here, we present a plasma-enhanced chemical vapor deposition (PECVD) method using elemental boron (B) and nitrogen (N) precursors to achieve wafer-scale growth and precise isotopic control of hBN films. High-quality hBN films are synthesized on Cu substrates via optimized B evaporation and N2 plasma activation. The growth mechanism involves an oxygen-mediated pathway for B transport and a layer-by-layer (Frank-van der Merwe) mode for multilayer formation. By employing isotopically enriched B powders (10B and 11B) and N2 gases (14N2 and 15N2), we demonstrate tunable isotopic compositions with phonon mode shifts quantitatively matching harmonic oscillator predictions. Furthermore, we realize unprecedented in-plane h10BN-h11BN heterostructures through dynamic B source switching during growth. This PECVD strategy establishes a transformative synthesis platform merging industrial-scale production capacity with atomic-scale isotopic precision, enabling new opportunities to engineer thermal transport, optical response, and quantum coherence in two-dimensional materials.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60648-2
The influence of mixing modes on the integrated process of co-pyrolysis of Naomaohu coal (NMH) and elm (ELM) with CO2 reforming of methane (CP-CRM) was investigated over Ni-based catalysts prepared by ball milling. Three mixing modes—NMH/ELM, ELM/NMH, and Blends—were examined and compared with co-pyrolysis under N2 (CP-N2). Results show that product distribution was significantly affected by mixing mode. The Blends mode achieved the highest tar yield, increasing by 35.29% compared with CP-N2. Light oil content in tar was higher, while pitch content was lower for Blends relative to layered modes. Phenols content in tar from Blends was 19.52% higher than CP-N2, and free radical concentration in tar was higher, attributed to enhanced heat and mass transfer between particles by mechanical mixing, promoting complete pyrolysis and efficient utilization of hydrogen-rich free radicals (·H, ·CHx) to suppress secondary cracking and polymerization. In contrast, NMH/ELM mode in CP-CRM improved phenols content by 33.27% over CP-N2. Free radical concentration in tar during CP-CRM was lower than in CP-N2, indicating timely stabilization of pyrolysis radicals by reforming-generated radicals. These findings provide guidance for regulating tar yield and composition in co-pyrolysis processes.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607018
To address the dual challenges of phosphorus resource scarcity and eutrophication control, this study proposed a sustainable waste-treats-waste strategy by preparing red-mud-modified sludge-based biochar (RMSBC) via co-pyrolysis of red mud and sewage sludge. The optimal material (RMSBC800), produced at 800 °C with a red mud-to-sludge mass ratio of 3:1, achieved a maximum phosphorus adsorption capacity of 28.57 mg/g, a 350% enhancement over unmodified biochar (SBC). Characterization (SEM, XRD, EDS, FT-IR, XPS) revealed that red mud modification increased the average pore size from 7.91 nm to 20.33 nm, reduced electronegativity, and raised the pH at point of zero charge (pHpzc) from 2.01 to 3.37. Adsorption kinetics followed the pseudo-second-order model, and isotherms fitted the Langmuir model, indicating monolayer chemisorption. The Freundlich parameter 1/n was 0.34, suggesting favorable adsorption. Mechanistic studies identified electrostatic attraction and surface precipitation as dominant, with molecular dynamics simulations confirming the critical role of Fe3O4 over Fe2O3 in adsorbing HPO4^2- due to stronger electrostatic interactions. The material retained 61% of its initial capacity after five regeneration cycles and achieved 83% phosphorus removal from real wastewater. This work demonstrates synergistic valorization of industrial wastes, offering an economically viable solution for phosphorus pollution control and resource recovery.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041505
To combat severe air pollution, China has implemented a series of air pollution control action plans since 2013, effectively alleviating PM2.5 pollution. However, PM2.5 concentrations in most cities within the Fenwei Plain still exceed national standards. This study systematically evaluates PM2.5 concentration changes across two policy phases (2013–2020) using the Community Multiscale Air Quality (CMAQ) model, quantifying contributions of meteorology and emissions, and analyzing sectoral source changes. Results show that annual average PM2.5 concentration declined cumulatively by 19% during 2013–2020. In the first phase (2013–2017), regional PM2.5 decreased by 3% annually, with most improvement in winter; however, due to unfavorable meteorology, concentrations increased in Xi'an and Xianyang. In the second phase (2017–2020), PM2.5 declined by an additional 16%, with more effective control measures, particularly in spring and autumn. Emission reductions dominated in both phases, with stronger effects in the second phase (−8 μg·m−3), significantly outweighing adverse meteorological contributions (+3.5 μg·m−3). Nevertheless, many cities still face challenges from unfavorable meteorology, highlighting the need for future policies to account for meteorological influences. Emissions from industrial, energy, and agricultural sources decreased significantly across both phases. However, during winter heating periods, residential emissions emerged as a source equal in importance to industrial emissions, becoming a key target for future emission controls.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3995-6
The deployment of single-site metal catalytic nodes into zirconium-based metal-organic frameworks (Zr-MOFs) offers vast advantages in catalytic recyclability, product separation, and mechanistic analysis, underscoring their paramount significance in heterogeneous catalysis. Nonetheless, their occupation within pores/channels usually diminishes mass transfer and catalytic efficiency during reactions such as the hydroboration of carbonyl compounds, especially for bulkier substrates. To address this issue, three microporous single-site Ti(IV) embedded Zr-MOFs with sequentially extended ligand arms are novelly synthesized to enable precise pore modulation ranging from 9.04, 10.12, to 11.18 Å. The catalytic performance is investigated using eight carbonyl compounds of varying sizes and four additional larger-scale substrates, which demonstrates that the catalytic efficiency is increased through pore size regulation, yet still away from optimal catalytic performance. Then a further strategy was shifted to the linker installation of linear dicarboxylate ligands chelated single-site Ti(IV) within coordination-unsaturated windows of mesoporous Zr-MOFs, and the result elucidates that the obtained catalyst exhibits superior catalytic efficiency (all exceeding 90%) while preserving the inherent mesoporosity of Zr-MOFs with a pore size of approximately 21.73 Å. We believe this research provides critical guidance for future research on structural design and catalytic optimization of MOFs, opening new avenues in heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4004-3
The development of efficient and stable oxygen evolution reaction (OER) electrocatalysts is critical for clean energy technologies, yet conventional cobalt-based spinel catalysts often suffer from insufficient activity and structural instability under operating conditions. To address these challenges, this study proposes and constructs a cation-ordered spinel-like catalyst (HVI Metal-CoMoO4/NF). The unique crystalline framework induces significant Jahn-Teller distortion and pre-stabilizes a Co2+/Co3+ mixed-valence state at the cobalt active centers via asymmetric Co–O–Mo bridges, effectively optimizing bulk charge transport. Electrochemical tests demonstrate that its performance significantly surpasses that of benchmark materials, requiring only an overpotential of 307 mV to drive a current density of 100 mA cm−2 in 1.0 M KOH, with a Tafel slope of 63.13 mV dec−1, maintaining stable operation for over 320 h at high current density. Crucially, our structural and in situ characterization results clearly reveal a stable and well-crystallized reconstruction behavior from the surface into the bulk of the spinel-like pre-catalyst during the OER. This work fundamentally addresses the challenges of disordered reconstruction and unstable active phases in traditional spinel catalysts, providing a paradigm for regulating the dynamic evolution of electrocatalysts through precise structural design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3968-3
The commercialization of perovskite solar cells (PSCs) is hindered by stability issues primarily stemming from interfacial defects. This study employed a machine learning (ML) screening approach and constructed a learnable weighted ensemble model (LWEM) to enhance prediction robustness for identifying effective interface passivation materials. The ML model predicted that an imidazolium salt-based interface modifier, 1-benzyl-3-methylimidazolium tetrafluoroborate (BMT), is suitable for planar n-i-p PSCs. Subsequent experimental results demonstrated that BMT provides synergistic passivation via an 'ion-coordination dual-lock' mechanism that significantly suppresses non-radiative recombination, facilitates hole extraction, and improves the quality of the perovskite film. The BMT-modified devices achieve a significant increase in power conversion efficiency (PCE) from 22.45% to 24.89% under AM 1.5G illumination, and attain a high PCE of 41.31% under 1000 lux light emitting diode (LED) indoor lighting. Additionally, the modified devices exhibit outstanding stability under long-term storage and maximum power point tracking conditions. This work provides a strategy for developing high-performance and highly stable PSCs for both indoor and outdoor applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4185-6
Electrochemical uranium extraction from fluorine-containing nuclear wastewater is critical for nuclear fuel recovery, yet current electrode materials suffer from limited scalability and insufficient long-term stability. Here, we report a bulk monoclinic Nb2O5−x (H-Nb2O5−x) derived from commercial bulk niobium oxide via rapid reconstruction, exhibiting exceptional activity and robustness for electrochemical uranium extraction in fluorine-rich environments. The intrinsic active pairs of low-valent Nb4+ and compact oxygen structure strongly bind with dominant uranyl fluoride species (UO2F+, UO2F2, UO2F3−, UO2F4^2−), facilitating efficient separation. In a 30 g L−1 fluoride solution, H-Nb2O5−x achieved a uranium extraction efficiency of 99.1%. Notably, in a 10-L real nuclear wastewater test, the bulk material maintained stable performance over 40 days, reducing uranium concentration from 1372.3 mg L−1 to 0.93 mg L−1. This work demonstrates a scalable, durable electrode material for industrial electrochemical uranium extraction, addressing the bottlenecks of complexation and stability in fluoride-containing waste streams.