SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3761-7
Ruthenium-based materials, including metallic Ru and RuO2, are promising electrocatalysts for electrochemical water splitting (EWS) due to their high activity for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). However, their practical application is hindered by the relatively strong adsorption of reaction intermediates on Ru surfaces and the oxidative dissolution of RuO2 under operating conditions. This review provides a comprehensive overview of recent progress and challenges in Ru-based electrocatalysts for EWS. We first summarize the fundamentals of EWS, including reaction mechanisms and activity descriptors. Then, we detail typical synthesis methods such as hydrothermal/solvothermal syntheses, organic ligand-assisted syntheses, pyrolysis, acid etching, cation exchange, and molten salt-assisted syntheses. Subsequently, we focus on enhancement strategies, including alloying, doping, structure design, interface engineering, single-atom catalyst design, high-entropy alloy design, phase engineering, and defect engineering, with typical examples illustrating structure-property correlations. Finally, we address remaining challenges and future prospects for the development of efficient and durable Ru-based electrocatalysts for sustainable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3773-7
Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells suffer from significant open-circuit voltage (VOC) deficits due to severe interfacial and bulk recombination, restricting their power conversion efficiency (PCE) far below the Shockley-Queisser limit. This work proposes a low-temperature annealing strategy during ITO sputtering (SA) to synergistically address these challenges. The temperature applied during ITO sputtering not only improves the crystallinity, carrier concentration, and optical transmittance of the ITO layer but also promotes the diffusion of In from ITO into both CdS and CZTSSe layers. Consequently, lattice matching at the CZTSSe/CdS interface is optimized, enabling epitaxial growth. And a favorable ITO/In:CdS/In&Cd:CZTSSe structure with optimal band alignment is obtained. As a result, a champion device with a PCE of 14.29% was achieved. The SA-treating also enabled the CZTSSe solar cells to achieve the highest VOC reported to date, exceeding 590 mV. This underscores the essential role of SA processing in optimizing interface engineering and suppressing defects, thus promoting the development of low-cost, high-performance kesterite photovoltaics.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60630-X
Chemical looping methane steam reforming (CL-MSR) enables sequential production of high-selectivity syngas and high-purity hydrogen via redox cycling, yet single iron-based oxygen carriers suffer from poor cycling stability, low reactivity, and sintering. This study modified Fe2O3/Al2O3 oxygen carriers with Cu, La, and Ce additives via dip-coating, and systematically characterized their physicochemical properties, reactivity, and hydrogen production performance. Results showed that spinel-phase CuFe2O4 exhibited higher reactivity than perovskite LaFeO3 and CeO2, promoting deeper reduction of Fe2O3. Fe58Cu2Al achieved an oxygen storage capacity of 6.5 mmol/g. During CH4 reaction, Fe58Cu2Al exhibited the highest oxygen loss of 12.1 g/100 g oxygen carrier, with syngas yield of 5.15 mmol/g—1.33 and 1.59 times that of Fe60Al. In hydrogen production, the 2% Cu-modified carrier yielded 5.13 mmol/g H2, 1.51 times that of pristine Fe60Al, with purity exceeding 98%. After ten cycles, H2 yield remained at 3.61 mmol/g, surpassing the single-cycle output of pristine Fe60Al (3.39 mmol/g), demonstrating superior dispersion and coking resistance. The study establishes Cu modification as an effective strategy to enhance reactivity and cyclic stability of iron-based oxygen carriers for CL-MSR hydrogen production.