SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506010
To facilitate accurate understanding and implementation of the provisions in the Technical Specification for Comprehensive Utilization of Titanium Gypsum (GB/T 45015-2024), and to promote technological capability in comprehensive utilization while effectively controlling environmental risks during utilization, this paper analyzes the current status and existing problems of titanium gypsum generation, management, and utilization technologies in China. The standard is systematically interpreted. It is concluded that the implementation of this standard will promote resource utilization of titanium gypsum, foster energy conservation and carbon reduction in the titanium dioxide industry, and further safeguard ecological and environmental security. China produces over 3,120×10^4 t of titanium gypsum annually (2023), yet its comprehensive utilization rate is only about 10%, far lower than that of phosphogypsum (~40%) and desulfurization gypsum (~80%). The standard, as the first national standard dedicated to titanium gypsum resource utilization, establishes technical pathways for building materials and ecological restoration, sets limits for soluble impurities, and specifies pollution control indicators throughout the utilization process. It addresses the long-standing gaps in technical standards, product quality variability, and environmental supervision, providing critical support for the green and low-carbon transformation of the sulfuric acid process titanium dioxide industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4028-5
The escalating thermal management demands of modern electronics necessitate materials with superior thermal conductivity and matched thermal expansion. Cu/Diamond composites are promising, yet their fabrication typically requires extreme conditions (high temperature/pressure) or complex coating processes. This work introduces a one-step, heat-source-free cold manufacturing method using ultrasonic vibration to consolidate Cu/Diamond composites at room temperature and a low pressure of ~16 MPa within seconds. The applied pressure is reduced by 200–500 times, and the required temperature is only 20% of that used in conventional high-temperature high-pressure sintering. Direct metallurgical bonding at Cu-Cu interfaces and solid embedding of diamond particles in the Cu matrix are achieved, yielding a composite with a high yield strength of 150 MPa. The method enables a maximum diamond proportion of ~60%, resulting in a thermal conductivity exceeding 1043 W/(m·K) and a coefficient of thermal expansion below 10×10⁻⁶ K⁻¹. Complex shapes are readily fabricated, and heat dissipation tests demonstrate superior performance compared to commercial Al₂O₃ and AlN substrates. The loose preparation conditions and rapid processing confer significant industrial production potential.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011804
Per- and polyfluoroalkyl carboxylic acids (PFCAs) are persistent organic pollutants whose isomers exhibit distinct environmental behaviors, bioaccumulation potentials, and toxic effects due to structural variations. Accurate identification of PFCA isomers is critical for risk assessment and pollution control, yet existing detection methods predominantly rely on standard references, posing challenges for precise analysis of isomers with subtle structural differences. Single-molecule electrochemical sensing via nanopores offers a standard-free approach by correlating molecular volume with current blockade, but its capability to distinguish PFCA isomers remained unverified. This study targeted three sets of PFCA isomers: 4,5,5-trifluoropent-4-enoic acid vs. 4,4,4-trifluoro-3-methylbut-2-enoic acid; 3,3,3-trifluoro-2-methylpropanoic acid vs. 4,4,4-trifluorobutanoic acid; and 2-(trifluoromethoxy)acetic acid, 3,3,3-trifluorolactic acid, and (2R)-3,3,3-trifluoro-2-hydroxypropanoic acid. By engineering nanopore interfaces (WT, R220N, R220Q Aerolysin) and extracting multi-dimensional characteristic parameters, the method achieved near 100% accuracy in identifying all seven isomers. Feature selection further enabled high classification accuracy with low data volumes, laying the foundation for rapid single-molecule detection of PFAS and other emerging contaminants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3829-7
Circularly polarized luminescence (CPL) is pivotal for advanced photonic applications, yet achieving concurrent high emission efficiency and large dissymmetry factors remains challenging. Here, we report a chiral reticular chemistry strategy to construct homochiral porous metal-organic frameworks (MOFs) as efficient CPL-active materials. By co-assembling enantiopure R/S-binol with achiral luminescent ligands, three pairs of enantiomeric pillar-layered MOFs were synthesized. These frameworks exhibit significantly amplified CPL responses, with |g_lum| values enhanced by up to two orders of magnitude compared to free ligands, reaching levels comparable to state-of-the-art chiral assemblies, while maintaining high photoluminescence efficiencies (Φ_PL up to 67%). Mechanistic investigations reveal that CPL originates primarily from the global chirality of the hierarchical frameworks rather than the intrinsic chirality of the precursors. This work establishes a robust design principle for porous CPL-active materials, offering new insights into chirality transfer and opening avenues to integrate strong luminescence with stable chirality in extended frameworks.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60658-5
Sulfur dioxide emitted from combustion of sulfur-containing aromatic compounds in fuels is a major contributor to atmospheric pollution. Oxidative desulfurization (ODS) has become a crucial complement to hydrodesulfurization (HDS) due to its mild reaction conditions and high efficiency in removing refractory aromatic sulfides. Metal doping is an effective strategy to modulate the electronic structure of catalysts and enhance catalytic performance. In this study, Mn-doped Co-V-O metal oxide (Mn-Co-V-O) was synthesized via a reflux method followed by high-temperature calcination. The structure, morphology, and surface chemical composition were characterized by FT-IR, XRD, SEM, XPS, and UV-vis DRS. The ODS performance toward dibenzothiophene (DBT) was evaluated using molecular oxygen as a green oxidant. Results indicated that Mn doping significantly enhanced the ODS activity compared to undoped Co-V-O. Under optimized conditions (110 °C, 0.03 g catalyst, 150 mL/min O2 flow, 20 mL model oil), a direct DBT removal rate of 81.6% was achieved. When combined with extraction, the desulfurization rate increased to 98.0%. Mechanistic studies revealed that Mn doping increased the surface oxygen vacancy concentration, facilitating oxygen activation to generate superoxide radicals (·O2−). Radical trapping experiments confirmed that ·O2− was the key active species responsible for selective oxidation of DBT to DBTO2. This study provides a reference for designing efficient metal oxide catalysts for deep oxidative desulfurization.