SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3536-5
Nanomaterial-based optical biomedicine and devices have attracted significant attention for tumor diagnosis and treatment, yet their application in tumor ablation is often hindered by limited functional integration and concerns over excessive radiation exposure. In this study, we address these challenges by developing a multifunctional fiber probe based on lanthanide-doped nanoparticles, featuring decoupled modules for localized heating and optical thermometry. This design enables synergistic therapy under near-infrared (NIR) laser irradiation. Beyond achieving precise photothermal ablation and real-time temperature monitoring, we uncovered a unique phenomenon: the generation of reactive oxygen species (ROS) by these nanoparticles under NIR laser excitation, even in the absence of traditional photosensitizers. Through a combination of experimental and computational approaches, we elucidated the physical mechanisms underlying ROS generation in wide-bandgap lanthanide nanoparticles. Leveraging these insights, we constructed an all-optical fiber system capable of simultaneous precise thermal control and photodynamic therapy. Our findings offer valuable guidance for the development of advanced optical nanomaterials and devices for effective tumor treatment, both in vivo and in vitro.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3657-9
Perovskite/silicon tandem solar cells (TSCs) have achieved power conversion efficiencies (PCE) up to 34.9%, surpassing the Shockley-Queisser limit of single-junction devices. The interconnection layer (ICL) critically bridges top and bottom subcells, enabling charge carrier recombination. Conventional indium oxide (In2O3)-based TCOs suffer from high-energy ion bombardment during sputtering, damaging amorphous silicon subcells and reducing open-circuit voltage (VOC) and fill factor (FF). Additionally, indium scarcity and cost necessitate indium-free alternatives. Here, we introduce a highly degenerate indium-free samarium-doped cadmium oxide (CdO:Sm) TCO as the ICL for perovskite/SHJ TSCs, deposited via low-damage reactive plasma deposition (RPD). The ultrathin CdO:Sm film (~3 nm) exhibits average transmittance of 85% (400–1200 nm) and 90% (800–1200 nm), enabling efficient near-infrared absorption in the bottom subcell. High doping concentration and mobility ensure excellent electrical conductivity. The low work function (4.04 eV) of CdO:Sm facilitates carrier tunneling and efficient recombination. Devices employing CdO:Sm ICL achieved approximately 1% higher efficiency compared to those with indium-based TCO ICLs. Detailed characterization including contact resistivity (1.68 mΩ cm2), conductive atomic force microscopy, Kelvin probe force microscopy, and photoluminescence quenching confirm enhanced carrier transport and extraction. This work demonstrates a viable indium-free ICL for high-efficiency perovskite/SHJ TSCs, addressing both performance and sustainability challenges.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112804
The rapid dissemination of antibiotic resistance genes (ARGs) in aquatic environments poses serious threats to public health and environmental safety under the 'One Health' framework. Nanoplastics (NPs), as co-occurring pollutants, can exacerbate ARG risks by promoting horizontal gene transfer (HGT), yet the influence of different functional groups on extracellular ARG (eARG) transformation remains unclear. This study investigated the effects of carboxy-modified polystyrene NPs (PS-COOH) and amino-functionalized polystyrene NPs (PS-NH2) compared to unmodified polystyrene NPs (PS) on the transformation of the extracellular resistance plasmid IE-V1955 (carrying an ampicillin resistance gene) into Escherichia coli DH5α. Results showed that PS-COOH exposure promoted plasmid transformation similarly to PS, with effects increasing over 0.1–20 mg·L−1. Low concentrations (0.1–0.5 mg·L−1) of PS-NH2 also enhanced transformation, with stronger effects than PS-COOH at equal doses, whereas high concentrations (1–20 mg·L−1) inhibited it. Mechanistically, PS-COOH (0.1–20 mg·L−1) and low PS-NH2 induced intracellular reactive oxygen species (ROS), increased cell membrane permeability, elevated the protein-to-polysaccharide ratio in extracellular polymeric substances (EPS), and promoted biofilm formation, thereby facilitating transformation. High PS-NH2 concentrations caused excessive ROS leading to cell lysis and formed aggregates with plasmids larger than membrane pores, blocking uptake. These findings provide a theoretical basis for assessing the combined environmental health risks of NPs and ARGs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112102
Based on the 2022 activity data of non-road mobile sources in Hebei Province, this study employed the emission factor method recommended by the Guidelines to estimate emissions of CO, HC, NOx, PM2.5, PM10, and SO2. A comprehensive emission inventory was established, followed by spatial and uncertainty analyses. Scenario analysis, aligned with the 14th Five-Year Plan policies, was used to project emissions for 2030. The results indicate that non-road mobile sources in Hebei emitted 76.1×10^3 t of CO, 20.6×10^3 t of HC, 164.0×10^3 t of NOx, 8.5×10^3 t of PM2.5, 9.0×10^3 t of PM10, and 2.4×10^3 t of SO2. Agricultural machinery was the dominant contributor to CO, HC, PM2.5, and PM10, accounting for over 60.0% of CO emissions. Railway locomotives were the primary source of NOx, contributing 50.9%. For SO2, agricultural machinery and railway locomotives contributed 39.0% and 44.4%, respectively. The highest emitting cities were Tangshan (21.3%), Shijiazhuang (15.7%), Cangzhou (11.6%), and Handan (11.6%). Ship emissions were concentrated in Tangshan Port; civil aviation emissions were mainly in Shijiazhuang, Tangshan, Qinhuangdao, and Handan; railway emissions were distributed in Shijiazhuang, Baoding, and Handan. Under the updated emission standard scenario, NOx and PM10 emissions in 2030 could be reduced by approximately 35.0%. The phase-out of old machinery yielded the largest reduction in CO (36.0%), while both electrification and phase-out scenarios significantly impacted HC emissions.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.226111
Efficient capture of the greenhouse gas nitrous oxide (N2O) is critical for climate change mitigation and resource recovery. In this study, two guanidinium-based hydrogen-bonded organic frameworks (HOFs) with pyridyl nitrogen site isomerism, namely G-5,5'-BPyDC and G-4,4'-BPyDC, were constructed using 2,2'-bipyridine-5,5'-dicarboxylic acid and 2,2'-bipyridine-4,4'-dicarboxylic acid as ligands. The effects of ligand structure on hydrogen-bonded network, pore environment, and N2O/N2 adsorption separation performance were systematically investigated via single-crystal X-ray diffraction, thermogravimetric analysis, Hirshfeld surface analysis, and gas adsorption experiments. Both frameworks are built via N-H...O hydrogen bonds. The asymmetric unit of G-5,5'-BPyDC contains two methanol molecules, resulting in larger free volume and surface area compared to G-4,4'-BPyDC, which exhibits more compact packing. Both materials show decomposition temperatures above 290°C, indicating good thermal stability. Hirshfeld surface analysis reveals that the total contribution of O-H/H-O and N-H/H-N hydrogen bonds in G-5,5'-BPyDC (32.0%) is higher than that in G-4,4'-BPyDC (29.7%). At 25°C and 4.0 MPa, the N2O adsorption capacity of G-5,5'-BPyDC is 2.32 mmol/g, surpassing that of G-4,4'-BPyDC (2.02 mmol/g). IAST calculations show that the selectivities of G-5,5'-BPyDC for N2O/N2 (50:50 and 10:90) mixtures reach 29.26 and 111.32, respectively, significantly superior to those of G-4,4'-BPyDC (6.61 and 17.03). Pyridyl nitrogen site isomerism effectively optimizes N2O/N2 adsorption and separation by modulating pore polarity and hydrogen-bonded network, offering a new strategy for isomer design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3814-2
Micro-structured surfaces have attracted increasing attention due to their great potential applications. However, it is still a challenge to continuously fabricate micro-structured surfaces based on thermoplastics by a facile, low-cost, and environmentally-friendly method. Herein, with the help of the extrusion molding method and an elaborately designed mold, micro-grooved fiber (MGF) based on high-density polyethylene (HDPE) is continuously prepared. Theoretically, infinitely long MGFs with feature sizes down to a few microns can be efficiently fabricated because of the continuous fabrication characteristic of the melt extrusion method. Interestingly, left- and right-handed micro-grooves with different helix angles can be produced by applying twisting at the die exit, and the macroscopically MGF springs can be further fabricated via a self-designed three-dimensional helical enwind device. By regulating wettability, MGF can achieve liquid self-transport on predefined paths. In addition, MGF fabric exhibits rapid evaporation behavior, whose evaporation rate is about 4 times higher than that of the Smooth fiber (SMF) fabric and 2 times higher than that of the most popular commercial quick-drying fabric (i.e., Cool-max fabric). This work proposes a facile and environmentally-friendly method for continuously preparing low-cost and flexible MGF, opening a new pathway to develop fiber-based microfluidic systems following the concept of "functionalized processing for thermoplastics".
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3963-5
Metal additive manufacturing (MAM) enables integrated one-piece fabrication of parts, high material utilization efficiency, and unparalleled design freedom. However, problems such as low production efficiency, difficulties in ensuring quality stability and defect control limit the large-scale industrial application of AM. In-situ active modulation for AM enables dynamic regulation of parts during the fabrication process, thereby enhancing the quality of the final fabricated parts without introducing extra processing steps. In-situ active regulation enables direct intervention during defect nucleation, providing better effectiveness than post-printing repairs while avoiding performance degradation risks associated with post-processing. Based on the difference of core factors directly affected during regulation, in-situ active regulation is categorized into the following. (1) Process and path parameter optimization, where regulation directly impacts manufacturing-related procedural rules. It is the simplest method of control and the preferred approach, with widespread attention focused on its effects on microstructure and mechanical properties. (2) Laser beam shaping, where regulation directly influences the energy carrier morphology. To address issues such as edge over-melting and localized energy deficiency caused by non-uniform energy distribution, laser beam shaping should be employed. (3) Additional physical field modulation achieved by superimposing supplementary physical fields. When optimal process and path parameters still fail to obtain the desired microstructure and mechanical properties, additional physical field control may be considered. Meanwhile, this work summarized the effects of different additional physical fields on the mechanical properties of various metallic base materials. The future trends of in-situ modulation in additive manufacturing are also discussed.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3855-8
The escalating environmental burden of plastic waste necessitates innovative chemical recycling strategies that circumvent the energy-intensive and catalytic limitations of conventional depolymerization. This study highlights a seminal advance by Qi Zhang, Da-Hui Qu, Ben L. Feringa, and co-workers, published in Nature Nanotechnology, which integrates supramolecular self-assembly with dynamic covalent chemistry to achieve catalyst-free, solvent-free polymer-to-monomer transformation. The system employs thioctic amide (TAA), a derivative of α-lipoic acid featuring reversible disulfide bonds and hydrogen-bonding amide groups. Notably, TAA monomers resist ring-opening polymerization upon melting due to cross-stacked packing driven by amide hydrogen bonds, which kinetically separates the 1,2-dithiolane rings. Introduction of formic acid (FA) as a supramolecular modulator disrupts the hydrogen-bond network, enabling dynamic disulfide ROP. Subsequent solvent removal yields nanocrystalline poly(disulfide) (Nc-poly(TAA)), which upon annealing at 120 °C reorganizes into a semicrystalline polymer (Sc-poly(TAA)) with a Young's modulus of 3.9 GPa, comparable to Nylon 6. The semicrystalline polymer exhibits hierarchical order with densely packed spherulites and periodic lamellae stabilized by reticular hydrogen bonds, conferring exceptional mechanical robustness and resistance to humidity (80% RH for six days). Rheological analyses reveal a relaxation time exceeding 90 years at room temperature, indicating a kinetically trapped, metastable state. Remarkably, the polymer reverts quantitatively to monomeric crystals under mild heating (120 °C, 24 h) without catalyst or solvent, achieving >90% purity and quantitative yield. The recovered monomer can be repolymerized to virgin-quality polymer, establishing a closed-loop cycle. Life-cycle assessment shows a carbon footprint of only 0.36 kg CO2 per kg product, underscoring the environmental benefits. This work demonstrates a fundamentally new route to circular polymers, merging supramolecular chemistry with dynamic covalent bonds for sustainable materials.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608026
Biochar and microbial inoculants are widely used for agricultural soil amendment. To investigate the effects of different straw biochars and Bacillus subtilis inoculant, applied individually or combined, on nitrogen transformation in dryland soil, a 60-day laboratory incubation experiment was conducted with six treatments: control (CK), 4% rice straw biochar (S), 4% rapeseed straw biochar (Y), 4% rice straw biochar plus 5 mg/kg inoculant (SJ), 4% rapeseed straw biochar plus 5 mg/kg inoculant (YJ), and inoculant alone (J). Results showed that rice straw biochar significantly increased soil nitrate nitrogen content by 148.74%–152.68% compared to CK, enhancing nitrification. Combined application with inoculant further increased average net nitrogen mineralization rate by 77.28%–99.38%. Conversely, rapeseed straw biochar decreased nitrate nitrogen by 51.66%–57.61%, and combined application reduced net nitrogen mineralization rate by 82.07%–84.73%. Treatments S, Y, SJ, and YJ promoted microbial biomass nitrogen (MBN) synthesis, with S and Y increasing MBN by 2.02- and 2.20-fold over CK, respectively. Combined treatments further increased MBN by 103.26%–149.44% relative to single biochar treatments. These findings indicate that biochar type governs nitrification and net nitrogen mineralization, while combined application exerts synergistic effects on MBN. For comprehensive dryland soil improvement, YJ treatment is optimal, reducing inorganic nitrogen loss risk and enhancing microbial nitrogen activity.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60721-9
Methane (CH4), the primary component of natural gas, is an ideal feedstock for producing high-value chemicals and clean fuels due to its high hydrogen-to-carbon ratio. However, its chemical inertness poses significant challenges, and traditional thermal catalytic reforming processes suffer from long reaction pathways and high energy consumption. Photocatalytic technology enables highly selective CH4 conversion under mild conditions, even at room temperature, offering environmental and economic benefits. This review systematically summarizes recent advances in room-temperature photocatalytic systems for direct CH4 conversion. It begins by elucidating the mechanisms, product distributions, and inherent challenges of four key reaction pathways: partial oxidation, non-oxidative coupling, oxidative coupling, and oxidative carbonylation. The discussion then addresses the critical role of catalyst architecture, focusing on semiconductor supports, metal site modulation, and advanced porous frameworks. Furthermore, reactor design and process intensification strategies are examined, including batch and continuous-flow reactors, novel structured reactors, and photo-electro and photo-thermo synergistic approaches. Finally, reaction mechanisms are summarized. Despite progress, challenges remain in fundamental understanding, performance evaluation, and technological integration. Future efforts should focus on mechanistic studies, standardization of evaluation protocols, development of non-noble metal catalysts, system optimization, and comprehensive sustainability assessments.