SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3681-6
Brominated butyl rubber (BIIR) is widely used in tires and biomedical products due to its excellent elasticity and gas barrier properties, but recycling end-of-life BIIR remains challenging because of its covalent cross-linked network. Here, we report a direct upcycling strategy for unmodified waste BIIR via nanoparticle-mediated interfacial crosslinking, avoiding chemical modification or degradation of the polymer structure. Pyridyl-functionalized silica nanoparticles (SiO2-Py) were synthesized and used to crosslink bromine atoms in waste BIIR with those of fresh BIIR, reconstructing the crosslink network without altering the original sulfur-vulcanization network. The resulting composites exhibit a dual interpenetrating network comprising the sulfur-vulcanized network and a bromine-pyridinium crosslinked silica-rich network, providing exceptional strength and toughness. Using discarded bicycle inner tubes as waste BIIR source, the upcycled composites achieved a tensile strength of ~14 MPa, toughness of ~60 MJ m−3, and ultra-low air permeability of 8.78×10−15 cm3 cm/(cm2 s Pa), significantly outperforming the original inner tube material. This work presents a scalable and effective solution for BIIR waste recycling, advancing sustainable development in the rubber industry.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506021
To elucidate the seasonal variation in cadmium (Cd) accumulation in ratoon rice and its relationship with root surface iron plaque, this study compared Cd concentrations in brown rice and the characteristics of iron plaque components (amorphous Fe, Am-Fe; crystalline Fe, Cry-Fe) between the main and ratoon crops of six rice varieties under different stubble heights. A field experiment was conducted in a Cd-contaminated paddy in Liuyang, Hunan (soil total Cd: 0.56 ± 0.06 mg·kg⁻¹). Ratoon crop treatments included low stubble (20 cm) and high stubble (60 cm). Brown rice Cd concentrations varied by variety, season, and stubble height. Low stubble generally increased brown rice Cd in the ratoon crop compared to high stubble; high stubble reduced Cd in most varieties relative to the main crop. Health risk assessment indicated that low stubble in the ratoon crop posed higher non-carcinogenic risk than the main crop and high stubble, while carcinogenic risks exceeded acceptable levels across all treatments. Iron plaque Am-Fe and Cry-Fe concentrations in the ratoon crop were generally lower than in the main crop, with Am-Fe consistently exceeding Cry-Fe. In the main crop, total Fe, Am-Fe, and Cry-Fe on root surfaces were significantly negatively correlated with brown rice Cd (P < 0.05), but correlations were not significant in the ratoon crop. High stubble reduced Cd accumulation and non-carcinogenic risk in most varieties, yet carcinogenic risk remained. Iron plaque significantly impeded Cd uptake in the main crop but its effect weakened in the ratoon crop. Selecting low-Cd-accumulating varieties and optimizing stubble height are key strategies for safe ratoon rice production in Cd-contaminated areas.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010201
The Guanzhong region, traversed by the Wei River Basin, is one of the most industrially, agriculturally, and medically advanced and densely populated areas in Northwest China, has seen increasing attention paid to the pollution of perfluoroalkyl substances (PFASs) in its surface water environment. This study systematically investigated the pollution characteristics of PFASs in the surface water of this region and their ecological and health risks. By optimizing the online solid-phase extraction-liquid chromatography-tandem quadrupole mass spectrometry (Online SPE-LC/MS/MS), efficient detection of 19 PFASs was achieved, with the method detection limits ranging from 0.2 ng·L−1 to 0.3 ng·L−1, linear correlation coefficients all ≥ 0.990, and spiked recoveries between 75.2% and 130.0%. Monitoring data indicated that PFBA, PFPeA, PFHxA and PFOS, short-chain perfluorinated compounds, were the main pollutants in this region, with high detection frequencies and concentrations, but the overall content was lower than that in most areas of China. The concentrations of PFASs in surface water showed significant seasonal variations, with the highest concentrations during the dry season (∑19PFASs:126.1 — 2584.3 ng·L−1), followed by the normal season (∑19PFASs:3.5—3567.6 ng·L−1), and the lowest during the wet season (∑19PFASs:26.3—294.6 ng·L−1). Ecological risk assessment showed that, except for PFDoDA in the dry season, the ecological risk quotient (RQ) of all other PFASs was < 1. Although the water of the Wei River is not used as direct drinking water, health risk assessment indicated that all PFASs posed low risks, with only PFOA and PFOS showing potential risks (HR > 0.1) to adults and children at some sites during dry/normal seasons. This study provides a scientific basis for PFASs pollution control in the Wei River Basin.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510041
This study presents a full-scale engineering practice of retrofitting an idle upflow anaerobic sludge blanket (UASB) reactor into an aerobic granular sludge (AGS) system for treating low-strength municipal wastewater. The design capacity was 20,000 m3/d (maximum 24,000 m3/d), achieving separate treatment of industrial and domestic wastewater to reduce operational costs. Systematic analysis covered hydraulic capacity enhancement, effluent quality, pollutant removal efficiencies, sludge granulation progress, and operational costs. Results showed rapid start-up: the system reached 75% of design capacity by day 10 and 90% by day 26. During a 4-month operation, average removal efficiencies for COD, NH4+-N, TN, and SS were 83.2%, 97.0%, 75.9%, and 94.4%, respectively, even under low influent BOD5/TN ratios (typically below 4). Granulation progressed quickly: by day 44, average particle size was 2.6 times that of the inoculum and over 4 times that of flocs, with granules (>200 μm) accounting for 17.3%; by day 110, these values increased to 3.2 times and 5 times, with granule proportion reaching 33.4%. Compared to the previous year (June–August), the AGS process reduced electricity consumption, chemical consumption, and sludge production by 77.3%, 25.4%, and 30.4%, respectively, while saving 65.6% of footprint. This ten-thousand-ton case provides a practical basis for AGS technology application in China.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0031
The high-temperature behavior of biomass ash critically influences gasifier operational efficiency. This study investigates the differential high-temperature behaviors of corn straw ash (CSA) and wheat straw ash (WSA) using an intelligent ash fusion analyzer, high-temperature rotating viscometer, X-ray diffraction (XRD), SEM-EDS, and FactSage thermodynamic simulations. Both ashes contain high K2O (>30%) and exhibit flow temperatures below 1300 °C. Despite higher K2O and lower SiO2, CSA exhibits a higher flow temperature (1241 °C) than WSA, attributed to elevated CaO (10.39%) and MgO (7.33%) that promote formation of high-melting silicates (K2MgSiO4, K2Ca2Si2O7, CaSiO3). In contrast, WSA with lower CaO (4.92%) and MgO (2.82%) tends to form low-melting potassium silicates. At high temperatures, both slags are typical crystalline slags, with viscosity rising sharply below a critical temperature. For CSA, rapid nucleation and coarsening of silicate crystals (e.g., KAlSiO4 grain size increases from 20.5 nm at 1350 °C to 192.9 nm at 1050 °C) cause abrupt viscosity increase. For WSA, a high P2O5 content (10.05%) induces a 'chemical dilution effect', leading to persistent KAlSiO4 during cooling and elevated viscosity, especially at the final cooling stage. This study elucidates how ash chemical composition governs high-temperature phase equilibrium and non-equilibrium kinetics, thereby macroscopically affecting ash fusion and rheological behavior, providing a theoretical basis for deeper understanding of biomass ash high-temperature characteristics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026012501
Childhood hypertension is a growing global concern, with approximately 4% of Chinese children exhibiting sustained elevated blood pressure meeting hypertension criteria, and single-time-point screening detecting rates of 14%–20% (up to 19% in obese children). Environmental exposure to metals (lead, cadmium, arsenic, mercury, copper, chromium) and bisphenol analogues (bisphenol A, S, F) has been implicated as a modifiable risk factor. This review synthesizes epidemiological evidence linking such exposures to blood pressure alterations in children and adolescents, highlighting dose-response relationships and potential mechanisms, including oxidative stress, endothelial dysfunction, and epigenetic programming. Key findings from cited studies indicate that low-dose bisphenol A exposure alters human cardiomyocyte functionality, and synergistic effects with insulin resistance elevate childhood blood pressure. Metal exposures, particularly lead and cadmium, are associated with increased blood pressure and cardiovascular structural changes. The review underscores the critical window of developmental exposure and the 'tracking phenomenon' linking childhood blood pressure to adult hypertension. Limitations include cross-sectional designs and confounding by mixed exposures. Future research should employ longitudinal cohorts and multi-pollutant models to refine risk assessment. Preventive strategies should integrate school health programs to reduce environmental exposure and monitor cardiovascular health.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3948-7
High-performance thermoelectric materials are typically narrow-band gap semiconductors. Here, by decoupling charge and heat transport in BaZrS3 with a band gap of about 1.9 eV, we made the emerging chalcogenide perovskite a high-performance thermoelectric material with only earth-abundant elements. Our first-principles calculations indicate that the high ionicity of BaZrS3 renders the electrons to propagate mainly through the Zr-4d orbitals, so that isovalent alloying Se on S sites minimally affects its charge transport while effectively suppressing lattice thermal conductivity. Using a flux-assisted solid-state method, we synthesized single-phase BaZrS3(1−x)Se3x samples with 0 ≤ x ≤ 0.25. As an indicator of decoupled charge and heat transport, the electron mobility is found barely degraded with increasing Se content, while the thermal conductivity is significantly reduced from 2.07 to 0.99 W m−1 K−1 at room temperature. This results in a record-high ZT of 0.81 at 750 K, a value never achieved for materials with band gaps greater than 1.5 eV, and the highest among all perovskite materials. Our work not only underscores the potential of wide band gap semiconductors as high-performance thermoelectric materials, but also demonstrates the strategy of decoupling the charge and heat transport for enhancing their thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4208-8
Sodium-ion batteries (SIBs) are emerging as a cost-effective alternative to lithium-ion batteries due to the abundance of sodium resources. Among cathode materials, P2-type layered oxides (Na_xTMO_2) offer high ionic conductivity and rate capability but suffer from low initial sodium content and Na+/vacancy ordering, leading to structural degradation and capacity fading. This study proposes a synergistic strategy combining high sodium content with Li/Mg co-doping to enhance the cycling stability of P2-type cathodes. The high sodium content increases the sodium reservoir, reducing the depth of desodiation for a given capacity, while Li/Mg co-doping mitigates Na+/vacancy ordering and stabilizes the crystal structure. The optimized cathode exhibits significantly improved cycling performance, retaining 82.3% of its initial capacity after 500 cycles at 1C, compared to 65.4% for the undoped counterpart. Furthermore, the co-doped material demonstrates enhanced rate capability, delivering 112 mAh/g at 5C, and suppressed phase transitions, as evidenced by in-situ X-ray diffraction. This work provides a rational design pathway for high-performance P2-type cathodes, addressing key bottlenecks in SIB commercialization.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3359-4
Dynamic fluorescent materials with stimulus-responsive emission modulation are pivotal for next-generation information security. This study presents a photoresponsive fluorescent composite system where spiropyran (SP) is covalently grafted onto naphthalimide-functionalized silica aerogel matrices. The architecture exhibits reversible fluorescence resonance energy transfer (FRET) between naphthalimide donors and merocyanine (MC) acceptors under ultraviolet irradiation, enabling dynamic emission shifting from green (blue) to red. Aggregation-induced emission (AIE) characteristics of SP are exploited to engineer a smart material system that reversibly regulates distinct red fluorescence by precisely controlling amino group dispersion on the naphthalimide-functionalized silica aerogels. This spatial manipulation governs the molecular packing state of SP, enabling dynamic fluorescence modulation. Programmable control over fluorescence chromatic transitions is achieved by systematically adjusting SP grafting densities (1%, 2%, and 3% w/w). A unique mode of dynamic information encryption technology is developed utilizing these dynamic fluorescence variations. The materials substantially enhance information encryption levels due to precisely adjustable fluorescence properties in response to external stimuli over time, making the encryption process unpredictable and complex, thereby exponentially increasing the difficulty for unauthorized replication or decoding. However, photostability requires further improvement (Table S3).
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3436-x
Aqueous zinc-ion batteries (ZIBs) are constrained by cathode materials that exhibit sluggish Zn2+ diffusion kinetics, structural degradation under hydrated Zn2+ insertion, and insufficient redox accessibility. This study reports a hierarchically porous vanadium-based metal-organic framework (h-V-MOF) cathode that integrates high specific surface area (1162.5 m2 g−1), reversible structural evolution, and mixed battery-supercapacitor charge storage. The h-V-MOF delivers a specific capacity of 304.1 mAh g−1 and retains 92.3% of initial capacity after 2000 cycles at 5.0 A g−1. Mechanistic analysis reveals that hierarchical porosity facilitates electric double-layer adsorption while vanadium redox centers enable stable Zn2+ insertion/extraction. The hybrid storage mechanism, combining surface-controlled capacitive contributions with diffusion-limited faradaic reactions, yields enhanced charge storage density relative to conventional oxide cathodes. These findings establish a design paradigm for MOF-based multifunctional electrodes in next-generation hybrid energy devices.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3732-2
The exploration and utilization of marine resources demand advanced operational tools. At present, deep-sea vehicles equipped with manipulators serve as the primary platforms for underwater exploration. However, the pressure sensors responsible for detecting the subtle gripping forces of these manipulators still face significant technical challenges, primarily due to the extreme hydrostatic pressure, corrosive seawater environment, and stringent mechanical strength requirements. A dual-curing, waterproof digital light processing (DLP) resin has been developed to achieve micron-scale printing accuracy, excellent seawater resistance, and mechanical properties comparable to those of thermoplastic resins. More importantly, the deep-sea pressure sensor (DSPS) features a unique printed lattice structure that allows seawater to penetrate and equilibrate the internal and external pressures, effectively mitigating the effects of deep-sea hydrostatic pressure. Experimental results demonstrate that the sensor exhibits a wide detection range and high sensitivity, with a measured sensitivity of 0.77 kPa−1 under 30 MPa hydrostatic pressure and a signal fluctuation below 1.48%. Furthermore, both the sensitivity and detection range of the sensor can be tuned by adjusting the lattice parameters, providing a robust foundation for the advancement of marine resource exploration.