Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606018
Swine wastewater, a high-strength organic effluent, offers a viable substrate for anaerobic biohydrogen production, aligning with clean energy recovery. This study compared hydrogen production in three anaerobic sequencing batch reactors (ASBRs) treating: raw wastewater (R1), supernatant after MAP (magnesium ammonium phosphate) precipitation for nitrogen and phosphorus recovery (R2), and the same supernatant with anaerobic sludge heat-treated at 75°C for 0.5 h (R3). Without pH adjustment, hydrogen production in R1 remained below 0.50 mmol/(kg·d). At an influent COD of 1800 mg/L, R2 and R3 achieved hydrogen production rates of 48.17 and 71.44 mmol/(kg·d), respectively. At COD 2400 mg/L, methane concentrations in R1, R2, and R3 were 10.8%, 14.2%, and 9.1%, respectively, indicating MAP pretreatment enhanced both hydrogen and methane production. As COD increased, R1's methane concentration rose to 14.6%, while average COD removal efficiencies for R1, R2, and R3 were 78.9%, 70.8%, and 52.5%, respectively. Under pH adjustment, all reactors peaked at pH 4.0, with hydrogen production rates of 0.10, 7.74, and 8.83 mol/(kg·d) for R1, R2, and R3, respectively. These findings demonstrate that MAP pretreatment combined with sludge heat treatment significantly enhances biohydrogen production, offering a promising strategy for swine wastewater valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3949-4
Sodium metal is considered an ideal anode material for high-performance sodium-based batteries. However, volume changes and dendrite growth during cycling seriously restrict its practical application. To address these challenges, this study utilizes harmful green tide algae Enteromorpha prolifera as a raw material to fabricate a self-supporting, sodiophilic, 3D Enteromorpha prolifera-derived carbon (EC) matrix via defect engineering. The results demonstrate that the 3D EC matrix can reduce nucleation overpotential, enhance binding ability with sodium atoms, and induce sodium to deposit horizontally inside EC, effectively addressing the issue of dendrite formation. Furthermore, the Na-EC symmetric cell demonstrates exceptional cycling stability with an ultralow polarization of 12 mV over 1000 h at 5 mA cm−2, 5 mA h cm−2. Notably, this stability persists even under ultrahigh current density and areal capacity conditions (30 mA cm−2, 30 mA h cm−2), maintaining stable operation for 500 h. When configured in full-cell systems with Na3V2(PO4)3 cathode, the assembled cell delivers an initial discharge capacity of 108.1 mA h g−1 at a 1 C rate, and maintains a capacity retention rate of 94.4% after 500 cycles. This study proposes an innovative strategy to advance high-performance dendrite-free sodium metal batteries through the recycling of marine environmental waste into functional energy materials.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3417-1
The increasing global incidence of diabetes necessitates advanced glucose monitoring technologies that offer continuous, painless, and user-friendly solutions. Non-invasive sweat glucose detection faces persistent challenges in sensitivity and selectivity. This work employs ultrathin SnO2 films, derived from liquid Sn-Bi alloy exfoliation and subsequent annealing, as the active channel in back-gate field-effect transistors (FETs) for glucose sensing. The defective surface hydroxyl groups serve as effective anchoring sites for stable glucose oxidase (GOX) immobilization. Enzymatic glucose oxidation generates positive charge accumulation on the SnO2 layer, modulating charge carrier density and enhancing channel current. This effect is amplified by the FET's subthreshold characteristics under negative back-gate voltage, enabling rapid, highly sensitive, and selective glucose sensing. The optimized device achieves an ultrahigh sensitivity of 1211.11 μA cm−2 μM−1 and demonstrates near-specific glucose detection in human sweat, indicating significant potential for non-invasive, continuous glucose monitoring in practical applications.