SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3575-4
Halide perovskite memristors, known for their ion mobility, have emerged as strong candidates for computational units in next-generation memory and neuromorphic computing systems. Nevertheless, most memristors are limited to operating in a single mode, either resistive switching or threshold switching. In this work, we overcome this limitation by developing dual-mode α-formamidinium lead triiodide (α-FAPbI3) perovskite memristors with switchable volatile/nonvolatile states, enabled by engineered SnO2 electron transport layers (ETLs). Through molecular interface optimization using 3-(N,N′-dimethylmyristylammonio) propanesulfonate (Z14) and 4,4′-(1,10-phenanthroline-3,8-diyl)bis(N,N′-bis(4-methoxyphen-yl)aniline) (PNL), we achieved exceptional device stability. Volatile devices exhibited >500 switching cycles, while nonvolatile devices surpassed 1000 cycles, both maintaining a high on/off ratio (~10^3). Beyond memory applications, these devices successfully emulated biological functionalities. The volatile mode replicated four key nociceptor characteristics (threshold, relaxation, sensitization, and no adaptation), while the nonvolatile mode demonstrated advanced synaptic plasticity, including paired-pulse facilitation (PPF) and spike-timing-dependent plasticity (STDP). Capitalizing on this dual-mode synergy, we constructed a spiking neural network (SNN) for handwritten digit recognition, achieving a 93% accuracy rate—a significant milestone for perovskite-based neuromorphic systems. This study not only provides a material-level strategy for multifunctional memristor design but also bridges the gap between biological sensing and artificial intelligence, paving the way for adaptive neuromorphic hardware.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61113-4
Porous pyrolytic carbon (PPyC) serves as the buffer layer in TRi-structural ISOtropic (TRISO) fuel particles, providing storage for fission gases, preventing damage to outer layers, and absorbing stresses caused by fuel-kernel swelling. However, the changes of PPyC micro- and meso-structure at high temperatures remain insufficiently understood. In this study, PPyC fabricated by chemical vapor deposition was heat-treated from 1200 to 1600 °C and characterized across atomic-to-mesoscopic scales. Results show that the structure changes with temperature with a transition at approximately 1400 °C. Below 1400 °C, a decrease in Raman ID/IG ratio, narrowing of the graphite diffraction peak, and increased sp2 hybridization indicate progressive ordering associated with defect redistribution. Concurrent decreases in true density and mesopore volume, together with increased closed porosity, are consistent with partial conversion of open pores into closed pores. Above 1400 °C, increased ID/IG ratio, broadening of the diffraction peak near the rhombohedral graphite (101) reflection, and transition regions between crystalline and amorphous material observed by TEM indicate increasing structural disorder. Meanwhile, initially distinct PPyC particle boundaries blur and merge into broad, plate-like domains. Subsequent decrease in closed porosity and increase in mesopore surface area are consistent with partial connection of closed pores to the open-pore network. This work shows that intrinsic coupling between atomic-scale structural change and mesoscale pore connectivity provides a basis for assessing high-temperature structural stability of PPyC in TRISO fuel particles.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510034
Phosphonate wastewater, characterized by stable C–P bonds, poses significant environmental risks due to its resistance to degradation and potential to contribute to eutrophication. This study developed a chloride-enhanced Fe(II)/PMS/H2O2 system for the oxidative degradation of 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTC) and simultaneous recovery of phosphorus as iron phosphate (FePO4). Under optimal conditions (0.1 mmol/L PBTC, 1.0 mmol/L Fe(II), 0.5 mmol/L PMS, 0.5 mmol/L H2O2, 10 mmol/L NaCl, initial pH 3.0, 60 min), total phosphorus (TP) removal reached 100%, with phosphorus nearly completely recovered as FePO4 precipitate. Increasing NaCl concentration and temperature enhanced TP removal, while pH significantly influenced removal efficiency and product speciation; acidic conditions (pH < 4.3) favored FePO4 precipitation. Coexisting Ca2+ and Mg2+ had negligible effects, whereas HCO3− and humic acid (HA) inhibited TP removal in a concentration-dependent manner. Radical quenching and electron spin resonance (ESR) analyses identified hydroxyl radicals (•OH), ferryl ion (Fe(IV)=O), sulfate radicals (SO4•−), and chlorine radicals (Cl•) as primary reactive species, with •OH playing a dominant role. Chloride introduction promoted the generation of multiple reactive species, and Cl• and its derivative Cl2•− directly attacked the C–P bond and phosphonate group, facilitating phosphorus release as PO43− and subsequent FePO4 formation. The system's feasibility was validated using actual industrial circulating cooling water. This study provides a novel approach for phosphonate wastewater treatment and phosphorus recovery.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041502
Microplastics (MPs), defined as plastic particles smaller than 5 mm, are ubiquitous environmental contaminants with documented presence in urban, rural, marine, remote, and polar atmospheres. The atmosphere serves as a primary medium for their long-range transport, raising concerns regarding climate interactions and human health. This review synthesizes recent advances in atmospheric MPs research, encompassing sampling strategies, pretreatment protocols, analytical techniques, occurrence characteristics, and ecological ramifications. Passive and active sampling methods are delineated, with active samplers enabling quantitative flux measurements. Pretreatment typically involves sequential steps of sieving, density separation, digestion, staining, and filtration to isolate MPs from complex matrices. Identification relies on visual inspection, micro-Fourier transform infrared spectroscopy (μ-FTIR), micro-Raman spectroscopy, laser direct infrared imaging (LDIR), and mass spectrometry. Reported atmospheric MPs predominantly exhibit dimensions below 700 μm, with fibrous morphologies being most prevalent. Color distribution is dominated by black, followed by white and transparent particles. Over 20 polymer types have been identified, with textiles, tire wear, and dust identified as principal sources. Atmospheric MPs can influence solar radiation balance, cloud formation processes, and pose risks to flora, fauna, and human health. However, research remains nascent; standardization of sampling and analytical protocols, along with comprehensive toxicological assessments, are critical knowledge gaps requiring urgent attention.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4222-9
The proliferation of high-frequency communication technologies has escalated electromagnetic (EM) pollution, posing risks to health and device reliability. Conventional microwave absorbers dissipate EM energy as heat, creating thermal management burdens and energy waste. This study introduces Bi2Se3 nanosheets, a topological insulator with surface conductivity and internal insulation, as a dual-functional material capable of both microwave absorption and thermoelectric conversion. Nanosheets with controlled morphology were synthesized via a polyol reduction method, with thickness and lateral size tuned by preparation conditions. The resulting composites exhibited excellent microwave absorption, achieving a broad absorption bandwidth of 2.95 GHz at sub-millimeter thickness. A multilayered structure design enabled full-band absorption from 2 to 18 GHz using a single absorbent. The Seebeck coefficient, derived from temperature differences up to 110 °C, was -152 μV/K, indicating efficient conversion of absorbed EM energy into electrical energy. This work demonstrates the potential of Bi2Se3 nanomaterials for self-powered electromagnetic devices, addressing both EM pollution and energy supply challenges.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3626-2
The development of durable electrocatalysts that overcome activity-stability compromises remains pivotal for advancing anion-exchange membrane fuel cells (AEMFCs). Herein, a rare earth-incorporated Pd-based metallene (PdLaCe) is engineered through lanthanide-based bimetallic coordination, resolving critical limitations in oxygen reduction reaction (ORR) catalysis. Combined experimental characterization and theoretical simulations reveal that La/Ce dual-doping induces charge polarization to generate Pdδ−-La/Ceδ+ active sites, synergistically optimizing the electronic structure via d-band center downshifting. This configuration weakens oxygen intermediate adsorption while enhancing structural integrity across thermal cycles. The optimized PdLaCe metallene delivers exceptional ORR performance, achieving a record half-wave potential of 0.903 V (vs. RHE) with negligible degradation (<6%) after 20,000 cycles, far surpassing commercial Pt/C benchmarks. Integrated into AEMFCs, it demonstrates a peak power density of 82.8 mW cm−2 alongside unprecedented stability (0.8 V for 22 h). Fundamental insights into lanthanide-induced charge redistribution establish a universal paradigm for designing robust multimetallic electrocatalysts via rare earth coordination engineering, bridging critical gaps between functional optimization and industrial-scale fuel cell applications. This work provides transformative strategies for next-generation energy conversion systems requiring high efficiency and ultra-stability.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3523-1
Natural surfaces with heterogeneous wettability inspire functional material innovations. Lubricant-infused slipperiness and heterogeneous three-dimensional (3D) micro-textures display diversified interface features and spatial topologies. However, constructing well-defined heterogeneous wettability on 3D micro-textures to create stable heterogeneous slippery surfaces remains challenging. Here, a 3D micro-heterogeneous wetting surface, featuring a lubricant sea dotted with superhydrophilic micro-islands, was fabricated via an innovative method without costly techniques. Tunable micro-island dimensions are supported for stable lubricant retention and programmable slipperiness. The flexibility and vertical heterogeneity enable the film advanced functions of deformation-responsive convertible adhesion and high-performance water collection. This work can greatly boost interfacial materials and extend their application in intelligent microfluidics and sustainable systems.