SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607006
This study evaluates the global warming potential (GWP) of three typical air pollution control device (APCD) configurations in municipal solid waste (MSW) incineration under ultra-low emission standards. The configurations are APCD1 (SNCR+SDS+DS+ACI+FF), APCD2 (SNCR+SDS+DS+ACI+FF+SCR+WS), and APCD3 (SNCR+SDS+DS+ACI+FF+WS+SCR). Life cycle assessment (LCA) was applied to quantify GWP. Results indicate that APCD3 exhibits the highest GWP due to increased electricity consumption, yet it achieves the lowest pollutant emissions among the three. APCD1 shows the highest NOx emissions, contributing significantly to GWP, and requires technological upgrades. APCD2 consumes more resources but does not proportionally reduce emissions, suggesting inefficiencies. Electricity consumption is the dominant factor influencing GWP across all processes; reducing electricity use and improving energy efficiency are critical for mitigating environmental impact. The study recommends further research on CO2 reduction strategies and adoption of more efficient DeNOx technologies to align MSW incineration with ultra-low emission and low-carbon goals.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3951-4
Silicon anodes offer an ultrahigh theoretical capacity (4200 mAh g−1) but suffer from >300% volumetric expansion during cycling and unstable solid electrolyte interphase (SEI) formation, leading to rapid capacity fading. Here, we design a hierarchical composite p-cSi@aSi@MgSiN2@C featuring a porous crystalline-amorphous silicon core (p-cSi@aSi), an in-situ MgSiN2 transition layer, and an outer nitrogen-doped carbon shell. The 3D interconnected pores accommodate volume expansion, while amorphous silicon enables isotropic lithiation-induced strain, eliminating crystalline phase transition barriers. The MgSiN2 layer transforms into a tough Li3N-rich SEI with ultra-fast ion channels, and the carbon shell provides mechanical confinement and electronic conductivity. This synergistic interface engineering achieves an initial coulombic efficiency (ICE) of 81.4%, a charge transfer resistance of 16.4 Ω after 200 cycles (64% reduction), and a Li+ diffusion coefficient of 1.72×10−11 cm2 s−1. The anode delivers 1719.3 mAh g−1 at 0.2 C after 200 cycles and 823.8 mAh g−1 at 0.5 C after 500 cycles. The molten salt electrolysis synthesis achieves a current efficiency of 68.12% and specific energy consumption of 12.76 kWh kg−1, with an estimated electricity cost of 1154.69 USD ton−1, only 20% of commercial Si/C anodes. This work resolves the ICE-cycle life trade-off and provides a scalable, cost-effective approach for next-generation high-energy batteries.