SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4319-x
This erratum corrects an error in the Acknowledgments section of the original article 'Investigation on graphene growth by roll-to-roll chemical vapor deposition' published in Science China Materials, Vol. 65, Issue 4, page 1042, 2022. The authors regret that the funding number (No. (2021)105) for the Shenzhen Science and Technology Program was incorrectly used. The correct funding number is No. KQTD20200820113010022. The authors apologize for any inconvenience caused. This correction does not affect the scientific content, results, or conclusions of the original paper. The original research focused on the kinetics of graphene growth via roll-to-roll chemical vapor deposition (CVD), a scalable method for producing high-quality graphene films. The study addressed challenges in continuous manufacturing, such as uniformity, growth rate, and defect control, and provided insights into optimizing process parameters for industrial-scale production. The erratum ensures accurate attribution of funding sources, maintaining the integrity of the research record.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509020
The AAOA-MBR (anaerobic-anoxic-oxic-anoxic membrane bioreactor) process is widely used in municipal wastewater treatment, but its multi-stage internal recirculation complicates sludge retention time (SRT) and carbon source distribution. This study systematically regulated three reflux ratios (R1: membrane tank to oxic tank; R2: oxic tank to anoxic I tank; R3: anoxic II tank to anaerobic tank) in a pilot-scale system (0.24 m3·d−1) to reveal their effects on nutrient removal and membrane fouling. When R1:R2:R3 = 300%:200%:100%, effluent COD, TN, TP, and NH3-N met discharge standards. Reducing R1 and R2, thereby decreasing total reflux ratio from R=6 to R=3, shortened SRT, which suppressed nitrifier accumulation and increased effluent COD and TN, but decreased TP. High-throughput sequencing of anoxic I and oxic tanks showed that denitrifying bacteria (Thauera and Ottowia) relative abundances decreased from 0.68% to 0.42% and 0.51% to 0.24%, respectively, while the phosphorus-accumulating organism Candidatus_Accumulibacter increased from 0.78% to 1.12%, enhancing phosphorus removal. Additionally, lowering R1 to 200% caused sludge accumulation in the membrane tank, exacerbating membrane fouling. Thus, internal recirculation ratios must be adjusted based on influent characteristics to balance nutrient removal and membrane performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3929-4
Hydrogels are extensively utilized in biomedical fields such as drug delivery, tissue engineering, and wound dressings due to their excellent biocompatibility, high water content, and tunable physicochemical properties. However, conventional hydrogels often undergo uncontrolled swelling in physiological environments, leading to mechanical degradation, structural destabilization, and functional failure, which severely restricts their long-term applicability. Recent advances have focused on developing anti-swelling hydrogels with equilibrium swelling ratios typically below 150%, achieved through strategies including the introduction of hydrophobic interactions, enhancement of cross-linking density, and incorporation of nanocomposite structures. These approaches significantly improve dimensional stability and mechanical integrity under physiological conditions. This review systematically summarizes the common preparation strategies for anti-swelling hydrogels and highlights their latest progress in biomedical applications, including wound dressings, tissue adhesives, and implantable devices. The advantages and future directions, such as smart responsiveness and multifunctional integration, are critically discussed. The review aims to provide theoretical guidance and technical references for the development of next-generation high-performance medical hydrogel materials.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607010
The impact of low concentrations of perfluorooctane sulfonate (PFOS) on anaerobic fermentation of waste activated sludge (WAS) remains poorly understood. This study applied three PFOS levels (0.5, 1.0, and 4.5 μg/g TSS) to systematically evaluate effects on organic matter solubilization and nitrogen/phosphorus transformations. Monitoring of soluble chemical oxygen demand (SCOD), soluble protein, polysaccharides, NH4+-N, PO43--P, and three-dimensional excitation-emission matrix (3D-EEM) fluorescence revealed that PFOS significantly enhanced release of SCOD, protein, and polysaccharides. At 45 °C after 14 days with 4.5 μg/g TSS, SCOD peaked approximately 28% higher than control, indicating increased biodegradable organic matter accumulation. NH4+-N concentrations rose overall with fluctuations, while PO43--P release was inhibited, suggesting interference with nutrient transformation pathways. 3D-EEM analysis showed strengthened signals of aromatic proteins and microbial by-products, confirming matrix solubilization. These findings demonstrate a dual effect of low-level PFOS: initial promotion of organic matter release followed by potential inhibition of nutrient transformation. This study provides data support for understanding PFOS environmental behavior in anaerobic digestion and informs sludge resource utilization and risk assessment of emerging contaminants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3904-6
Disrupting calcium ions (Ca2+) homeostasis to induce calcium overloading has emerged as a promising strategy for cancer therapy. However, calcium overloading based on exogenous calcium salts (such as calcium carbonate and calcium peroxide) can easily lead to off-target Ca2+ release, causing severe side effects such as hypercalcemia and cardiac or renal dysfunction. This review explores the calcium-free nanomaterials for mediating targeted calcium dysregulation in tumors. These nanomaterials function not by carrying Ca2+ but by precisely regulating endogenous calcium signaling pathways. They promote massive Ca2+ influx through targeted activation of calcium channels and/or inhibit Ca2+ efflux by suppressing pumps, effectively triggering intracellular calcium accumulation. Such a strategy efficiently induces mitochondrial dysfunction, endoplasmic reticulum stress, and immunogenic cell death, thereby inhibiting tumor growth and metastasis while potentiating antitumor immunity. We systematically summarize the design principles, mechanisms of action, and therapeutic applications of these calcium-free nanoplatforms, highlighting their potential to overcome the limitations of traditional therapies and boost ion-interference-based cancer treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607025
The Holocene alluvial-diluvial stratum of the Quaternary is characterized by high soil hydraulic conductivity and intense surface water-groundwater interaction, which leads to rapid and extensive migration of contaminants from landfills. To investigate the contaminant characteristics of a municipal solid waste (MSW) landfill in such strata, a case study was conducted at a landfill in southwestern China. Methods including the Nemerow pollution index and the potential ecological risk index were employed to systematically analyze the contamination of groundwater and soil, as well as the spatial distribution of organic matter and heavy metals. The results showed that the groundwater was severely contaminated (PI > 3). The maximum exceedance multiples for total bacterial count, ammonia nitrogen (NH4+-N), and total coliforms relative to the standard limits were 36, 9.5, and 8, respectively. The composition of the contaminants in groundwater was highly consistent with the characteristics of landfill leachate. For the soil, the concentrations of six heavy metals (Cu, Pb, Cd, Ni, Hg, and As) were all below the Class II screening values of the standard GB 36600—2018. Both the Nemerow pollution index (PI < 0.7) and the potential ecological risk index (RI < 150) indicated that the soil environment was safe. Regarding soil dissolved organic matter (DOM), humic-like substances (22.9% to 34.9%) and fulvic-like substances (22.4% to 27.5%) were the dominant components, and their fluorescence intensities exhibited an exponential decay trend with increasing soil depth. The speciation of Cu, Pb, As, Hg, and Ni was dominated by the residual fraction (52.33% to 90.32%). However, over 70% of Cd existed in active forms (exchangeable + Fe/Mn oxide-bound), suggesting a high migration risk. The horizontal distribution of heavy metals showed regional specificity, with high-value areas mainly concentrated in the screening waste and soil stacking areas. Vertically, Cu and Cd exhibited surface enrichment, while As, Hg, Pb, and Ni were enriched in the groundwater fluctuation zone. These findings indicate that groundwater in alluvial-diluvial strata is highly susceptible to leachate contamination, while soil heavy metal contamination is not significant, with low levels in the aquifer but a tendency to accumulate at the water-soil interface. It is recommended that during landfill remediation, attention be paid to anti-seepage measures in waste excavation and stacking areas, as well as the interception and remediation of the groundwater fluctuation zone, to prevent secondary contamination of soil and groundwater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3998-8
Constitutional isomerism in covalent organic frameworks (COFs) has emerged as a powerful strategy to tailor material properties for photocatalytic applications. Here, we report the design and synthesis of two isomeric multicomponent COFs (MC-COFs) via Schiff-base condensation followed by Povarov reaction, converting imine linkages into quinoline structures. These isomeric MC-COFs exhibit opposing C=N bond orientations and distinct phenyl group alignments within the COF pores, leading to different torsion angles in the COF layers. Structural analyses reveal that enhanced planarity promotes π-π stacking and electron delocalization, resulting in favorable band structures and reduced exciton binding energies. Consequently, the optimized COF achieves a superior hydrogen peroxide (H2O2) production rate of 3128 μmol g−1 h−1 under visible light irradiation. This work underscores the critical influence of structural isomerism on the photocatalytic efficiency of MC-COFs and provides insights for rational design of high-performance COF-based photocatalysts.