SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61066-9
Carbon materials suffer from limited dielectric loss, resulting in poor impedance matching and inadequate microwave attenuation. To address this, hierarchical structures with synergistic loss mechanisms are sought. Here, biomass cattail serves as a sustainable precursor for nitrogen-doped carbon nanotube arrays decorated with Fe3C nanoparticles via chemical vapor deposition, yielding Fe3C@NCNTs/CMTs composites. The crystallinity, tuned by calcination temperature, critically influences microwave absorption. At 800 °C, the composite achieves a minimum reflection loss of –35.8 dB and an effective absorption bandwidth of 7.02 GHz at a thickness of only 1.7 mm, with an ultralow filler loading of 10 wt%, covering the entire Ku band and part of the X band. This performance stems from enhanced magnetic loss and multiple dielectric polarization mechanisms. The study demonstrates a promising strategy for designing biomass-derived carbon-based broadband microwave absorbers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604019
A two-stage electrostatic precipitator (ESP) integrating a sawtooth-rod electrode precharging unit and a plate-plate collection unit was developed for simultaneous removal of fine particles and volatile organic compounds (VOCs) from catering fumes. Using KCl particles and toluene as surrogates, the system achieved a fine particle (<0.3 µm) collection efficiency of 91% and a total particle collection efficiency exceeding 98% at applied voltages of +12 kV (sawtooth-rod) and -8.5 kV (plate-plate), with an ozone concentration of 176.9 mg/m³. The presence of particles enhanced toluene degradation, increasing removal efficiency from 29.2% to 53.1%. Positive DC discharge on the sawtooth-rod electrode yielded a higher corona current (800 µA vs. 375 µA for negative) and lower ozone generation (101.4 mg/m³ vs. 176.9 mg/m³), indicating superior suitability for catering fume treatment. The stable discharge characteristics of the sawtooth-rod electrode reduce energy consumption and extend operational cycles, offering a promising technical pathway for efficient, compact, and intelligent ESP systems in catering fume purification.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510084
The rapid expansion of lithium battery industries has elevated lithium resources to strategic importance, yet lithium extraction generates 8–10 tons of slag per ton of lithium salt, with complex heavy metal content and high leaching risks. This study improves conventional alkali activation by employing a composite activator and multi-stage thermal assistance to achieve self-solidification of lithium slag, simultaneously immobilizing multiple heavy metals while producing high-strength materials. Under full slag conditions, the mechanical strength of solidified materials ranged from 3.48 to 8.25 MPa; after optimization, strength increased by 137.07%. Average immobilization rates for various heavy metals rose from 97.26% to 99.77%. In simulated acidic, alkaline, neutral, high-salt, acid rain, and leachate environments, efficient immobilization was maintained, with leachate concentrations below regulatory limits. The improved activator and thermal process reduced structural defects, promoted formation of the key Si-O-Al framework, and ensured structural integrity, enhancing both mechanical strength and heavy metal immobilization. The cost of slag solidification was approximately 185–200 CNY per ton, significantly lower than conventional methods, with low energy consumption, no high-temperature calcination, and reduced equipment and reagent requirements, supporting scalability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510029
Low hydrolysis efficiency is a core bottleneck in anaerobic digestion (AD) of lignocellulosic agricultural residues, limiting methane production and resource utilization. This study optimized thermal hydrolysis pretreatment (THP) of corn straw (CS) using response surface methodology (RSM) to enhance methane yield. The optimal conditions were determined as solid-to-liquid ratio of 51.0–57.5 mg·mL−1, pretreatment time of 74–81 min, and temperature of 182.5–197.5 °C. Under the optimal combination (52.3 mg·mL−1, 78.4 min, 191 °C), cumulative methane yield increased from 218.0 to 362.9 mL·g−1 VS, a 66.7% improvement over untreated CS. Characterization via XRD, FTIR, and SEM revealed that THP disrupted the lignocellulosic structure, reducing lignin content from 21.5% to 8.3% and crystallinity index (CrI) from 70.83% to 61.95%. Inhibitory derivatives generated during THP included furfural (1.69 mg·mL−1), 5-methylfurfural (2.44 mg·mL−1), and phenol (23.14 mg·L−1), with a theoretical combined inhibition rate of 7.26%. The promotion effect on methane production (66.7%) far exceeded the theoretical inhibition (7.26%), indicating that THP under optimized conditions is effective and environmentally controllable. This study provides a systematic framework for optimizing THP parameters to maximize methane production from agricultural residues.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3974-1
MAB-phase-derived compounds exhibit promising electromagnetic wave (EMW) absorption properties due to their unique layered structure and desirable physicochemical characteristics. Among them, Cr2AlB2 is particularly attractive owing to its excellent thermal and electrical conductivity. However, conventional synthesis of Cr2AlB2 requires inert gas protection to prevent oxidation, significantly increasing production costs and limiting its application in EMW absorption. To overcome this bottleneck, we report the successful synthesis of high-purity Cr2AlB2 in ambient air using the molten salt shielded synthesis (MS3) method. This approach not only isolates the material from oxygen interference but also reduces the synthesis temperature, offering a cost-effective and scalable route. The as-synthesized Cr2AlB2 exhibits outstanding EMW absorption performance: a minimum reflection loss (RLmin) of -42.10 dB at 12.6 GHz and a maximum effective absorption bandwidth (EABmax) of 3.44 GHz at a thickness of 1.9 mm. This work not only facilitates the large-scale production of Cr2AlB2 but also provides critical insights into its practical application as a high-performance EMW absorber.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4072-3
All-inorganic, hole-transport-material-free (HTM-free), carbon-based perovskite solar cells (C-PSCs) have attracted significant attention due to their exceptional stability and low cost. However, their performance and commercial potential are constrained by poor interfacial contact, insufficient crystallinity, and energy level misalignment. In this work, we address these challenges via a molecular engineering strategy by introducing tetrakis(4-ethynylphenyl)methane (TEPM) as a multifunctional additive. The alkynyl moiety (C≡C) in TEPM coordinates with Pb2+ ions in perovskite precursors, synergistically slowing crystallization kinetics to regulate crystal growth and passivate deep-level defects. Consequently, CsPbI3 films exhibit larger grain sizes, improved crystallinity, and lower defect densities. Devices modified with TEPM achieved a record power conversion efficiency (PCE) of 20.01% (certified 19.58%). Additionally, unencapsulated devices retained 87.6% of their initial efficiency after 1080 h under ambient conditions (25 °C, 30% relative humidity), and maintained 94.0% of their initial efficiency after 730 h of continuous AM 1.5G illumination in air. This work sets a new efficiency benchmark for inorganic HTM-free C-PSCs and provides a versatile molecular engineering strategy for developing high-performance, stable perovskite photovoltaics.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3510-0
The activity and stability of single-atom catalysts (SACs) are intimately associated with the structure of supports. Herein, by employing a van der Waals (vdW) heterostructure support, we construct a highly active and durable Pt SAC for hydrogen evolution reaction (HER). The unique support consists of monolayer MoS2 attaching on hierarchical N-doped carbon nanocages (hNCNC), on which Pt presents as individual single atoms on the hNCNC and as island-like single-atom layers on the MoS2. The optimized Pt1-MoS2/hNCNC demonstrates low overpotential (11 mV at 10 mA cm−2) and high mass activity (5.6 A mgPt−1 at −20 mV) in 0.5 M H2SO4 solution, outperforming commercial Pt/C. Impressively, the Pt1-MoS2/hNCNC exhibits improved long-term stability in proton exchange membrane water electrolyzer relative to commercial Pt/C. The excellent HER performance is attributed to the regulated electronic structure, robust interaction of Pt atoms with MoS2/hNCNC and facilitated charge transfer. This study establishes an innovative strategy to develop a highly active and durable Pt SAC using vdW heterostructure supports.