SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4183-3
Excessive ultraviolet (UV) radiation poses significant risks to human health, necessitating highly sensitive detection systems. Organic photodetectors (OPDs) offer high sensitivity and tunable spectral response, but their UV performance is constrained by conventional glass/indium tin oxide (ITO) substrates and electrodes, and insufficient photoactive layer responsivity. Here, we report high-performance UV-OPDs achieved through UV-transparent window and active-layer optimization. Replacing glass/ITO with a UV-transparent window comprising a quartz substrate and PH1000 electrode enhances UV transmittance. Integrating the high UV-responsive blend PM6:Y6:PC71BM as the active layer, the optimal ternary UV-OPD exhibits external quantum efficiency (EQE) exceeding 53% across 280–400 nm, with a peak EQE of 78.29% and responsivity of 214.68 mA/W at 340 nm, alongside a rapid response time of 2.6/2.1 μs. This performance represents the best combination of responsivity and response time reported to date in the UV region. We demonstrate the potential of these UV-OPDs for outdoor real-time UV monitoring. This work presents a promising strategy for developing high-performance UV-OPDs through transparent substrate and electrode engineering, and active-layer optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3662-4
Luminescent thermometry has become a research hotspot due to its high spatial resolution, fast response, and non-invasive nature. However, achieving high-performance temperature imaging requires both luminescent materials with high temperature sensitivity and efficient imaging methods, which remains a significant challenge. In this study, a series of pure-phase rubidium germanate phosphors doped with manganese were synthesized and encapsulated into polydimethylsiloxane (PDMS) films to improve chemical stability. The dramatic temperature-dependent luminescence behavior of Mn4+ in the Rb2Ge4O9 matrix provides reliable and efficient methods for temperature sensing. The high-sensitivity temperature sensing capability of the Rb2Ge4O9:0.002 Mn4+ fluorescent film has been confirmed, leveraging temperature-dependent emission intensity, luminescence decay lifetime, and time-resolved intensity ratio techniques. Notably, Rb2Ge4O9:Mn4+ fluorescent film exhibits a strikingly high relative sensitivity of 17.03% K−1 at 330 K in the time-resolved thermometry scheme, which is the highest relative temperature sensitivity within the physiological temperature range known to us. High-performance temperature imaging of the fluorescent film is achieved through the time-resolved intensity ratio strategy with a best practical temperature resolution of 0.08 K at 325 K. Furthermore, the temperature images of an operating nickel circuit with a line width of 20 μm under different working currents were recorded, showing a clear circuit microstructure and temperature gradient. These findings pave a novel path for realizing high-performance temperature imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3666-2
Light-emitting electrochemical cells (LECs) are promising for low-cost, solution-processed display and lighting applications, yet achieving high efficiency and color purity remains challenging. Here, we report two ionic multi-resonance (MR) emitters with narrowband blue emission for high-color-purity LECs. By covalently bonding an imidazolium functional group into a boron/nitrogen-doped polycyclic skeleton, the emitters retain the narrowband emission and high photoluminescence quantum yield (PLQY) of the MR core while gaining ionic character. The design exploits two types of nitrogen atoms in the imidazolium unit: the pyrrolic N at the 1-position forms a para-B-π-N linkage, elevating excited-state energy levels and blue-shifting emission; the pyridinic N at the 3-position provides a quaternization site, yielding intrinsically ionic emitters compatible with ionic hosts. The emitters exhibit blue emission with narrow full-width at half-maximum of 26–27 nm and high PLQYs of 95%–97% in solid-state films. LECs based on these emitters achieve narrowband blue electroluminescence with CIE coordinates of (0.12, 0.26) and a maximum external quantum efficiency (EQE) of 4.6%, representing the first narrowband blue LECs based on intrinsically ionic MR emitters. This work demonstrates a viable molecular design strategy for high-color-purity LECs, addressing the long-standing trade-off between efficiency and color purity in this technology.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012302
Phosphorus (P) loss from paddy fields contributes to eutrophication in Chaohu Lake. This study evaluated the effects of novel fertilizers and P reduction on P loss and rice yield. Seven treatments were established: no P (CK), rice-specific fertilizer (ZYF), slow-release blended fertilizer (SRF), Xinjutian compound fertilizer (XJT), enhanced loss-controlled fertilizer (CRF), CRF with 10% P reduction (CRF-10P%), and CRF with 30% P reduction (CRF-30P%). Results showed that novel fertilizers and P reduction significantly reduced concentrations of total phosphorus (TP), dissolved phosphorus (DP), and particulate phosphorus (PP) in surface water and leachate. The first 5 days after basal fertilization and heavy rainfall were high-risk periods for P loss. Rainfall increased TP concentrations by 417.74%–432.86% and 94.85%–351.35% in surface water and leachate, respectively; DP increased by 120.80%–322.44%, and PP by 280.66%–501.77% and 80.23%–297.55%. Compared with ZYF, SRF, XJT, and CRF reduced TP loss by 15.43%–33.95%, with SRF showing the lowest loss. Under P reduction, CRF-10P% and CRF-30P% reduced TP loss by 31.48% and 37.04%, respectively, with CRF-30P% achieving the lowest loss. Notably, CRF-10P% increased rice yield by 22.37% relative to ZYF, indicating that moderate P reduction with enhanced loss-controlled fertilizer can maintain or increase yield while reducing environmental risk. The study concludes that CRF-10P% offers a promising strategy for sustainable rice production in the Chaohu Lake watershed.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225162
The effects of tempering temperature on the microstructure, strength-toughness balance, and precipitates of a quenched Cu-Cr-Ni ultra-high strength weathering steel were systematically investigated. The steel was austenitized at 920°C, quenched, and then tempered at 500°C, 550°C, and 600°C. Microstructural characterization was performed using optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), while mechanical properties were evaluated via tensile and low-temperature impact tests. Results showed that as the tempering temperature increased from 500°C to 600°C, the microstructure transformed from lath-shaped tempered sorbite to a non-lath morphology. The fraction of rod-like cementite decreased, while spheroidized cementite increased, and the size of MC (M = Ti, Nb, V, Mo) precipitates decreased from an average of 12.2 nm to 9.9 nm. Consequently, yield strength and tensile strength decreased from 935 MPa and 958 MPa to 866 MPa and 888 MPa, respectively, whereas total elongation and impact energy at -40°C increased continuously, reaching maximum values of 5.0% and 280 J at 600°C. When tempered at 550°C, the steel exhibited a yield strength of 895 MPa, tensile strength of 921 MPa, elongation of 4.3%, and impact energy of 271 J at -40°C, demonstrating an optimal combination of strength and toughness. This improvement is primarily attributed to the spheroidization of cementite and the uniform dispersion of fine MC precipitates, which alleviate stress concentration, along with the softening of the acicular ferrite matrix during tempering.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606017
Against the backdrop of global green transition and tightening resource constraints, China's Dual Carbon Goals and Zero-Waste City initiative have positioned waste valorization as a critical pathway for sustainable development. Zinc, a fundamental metal, faces high external dependence and nearing primary resource limits, making the regenerated zinc industry essential. However, the previous standard YS/T 1093-2015 lagged in classification, technical indicators, and environmental requirements. This paper analyzes the revision to YS/T 1093-2024, which renames the standard to 'Recycled Zinc Raw Materials' and clarifies its role as front-end smelting intermediate feedstock. The new standard establishes a classification system covering six typical zinc-bearing materials, expanding utilization of low-grade complex materials (zinc content 5%-15%). It tightens limits on harmful elements (fluorine, chlorine, lead, arsenic) and introduces moisture control and appearance evaluation indicators, enhancing operability and environmental risk control. Compared with EU standards, it shows systematic improvements in raw material coverage, process adaptability, and environmental risk prevention. The revision is expected to drive the regenerated zinc industry toward intensification, high-value utilization, and clean production, improving resource recycling efficiency and supporting China's zinc resource strategic security and low-carbon development.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3944-9
Hard carbon (HC) is a promising anode material for sodium-ion batteries (SIBs) but suffers from low initial Coulombic efficiency (ICE) and unstable solid electrolyte interphase (SEI). Here, we report a dual-functional strategy combining surface engineering and solution chemical pre-sodiation. A graphitic carbon coating on HC acts as a conductive buffer network and shields surface defects, while sodium biphenyl (Na-Bp) pre-sodiation drives sodium ions into the material via a potential difference, inducing a pre-SEI layer that matures into a thin, dense, NaF-rich inorganic SEI during cycling. This approach compensates for irreversible sodium loss and enhances cycling stability. The pre-sodiated electrode (pCH4-HC) achieves an ICE of 99.5% and a reversible capacity of 321.7 mAh g−1, compared to 54.2% for untreated HC. Long-term cycling shows 74.0% capacity retention after 1000 cycles at 300 mA g−1. In full-cells with NaNi1/3Fe1/3Mn1/3O2 (NFM) cathode, pCH4-HC||NFM delivers 81.9 mAh g−1 after 100 cycles, demonstrating excellent stability and rate performance. This dual-strategy approach validates the adaptability of pre-sodiation technology for high-performance SIBs.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510029
Low hydrolysis efficiency is a core bottleneck in anaerobic digestion (AD) of lignocellulosic agricultural residues, limiting methane production and resource utilization. This study optimized thermal hydrolysis pretreatment (THP) of corn straw (CS) using response surface methodology (RSM) to enhance methane yield. The optimal conditions were determined as solid-to-liquid ratio of 51.0–57.5 mg·mL−1, pretreatment time of 74–81 min, and temperature of 182.5–197.5 °C. Under the optimal combination (52.3 mg·mL−1, 78.4 min, 191 °C), cumulative methane yield increased from 218.0 to 362.9 mL·g−1 VS, a 66.7% improvement over untreated CS. Characterization via XRD, FTIR, and SEM revealed that THP disrupted the lignocellulosic structure, reducing lignin content from 21.5% to 8.3% and crystallinity index (CrI) from 70.83% to 61.95%. Inhibitory derivatives generated during THP included furfural (1.69 mg·mL−1), 5-methylfurfural (2.44 mg·mL−1), and phenol (23.14 mg·L−1), with a theoretical combined inhibition rate of 7.26%. The promotion effect on methane production (66.7%) far exceeded the theoretical inhibition (7.26%), indicating that THP under optimized conditions is effective and environmentally controllable. This study provides a systematic framework for optimizing THP parameters to maximize methane production from agricultural residues.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3974-1
MAB-phase-derived compounds exhibit promising electromagnetic wave (EMW) absorption properties due to their unique layered structure and desirable physicochemical characteristics. Among them, Cr2AlB2 is particularly attractive owing to its excellent thermal and electrical conductivity. However, conventional synthesis of Cr2AlB2 requires inert gas protection to prevent oxidation, significantly increasing production costs and limiting its application in EMW absorption. To overcome this bottleneck, we report the successful synthesis of high-purity Cr2AlB2 in ambient air using the molten salt shielded synthesis (MS3) method. This approach not only isolates the material from oxygen interference but also reduces the synthesis temperature, offering a cost-effective and scalable route. The as-synthesized Cr2AlB2 exhibits outstanding EMW absorption performance: a minimum reflection loss (RLmin) of -42.10 dB at 12.6 GHz and a maximum effective absorption bandwidth (EABmax) of 3.44 GHz at a thickness of 1.9 mm. This work not only facilitates the large-scale production of Cr2AlB2 but also provides critical insights into its practical application as a high-performance EMW absorber.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3924-x
Metal halide perovskite solar cells (PSCs) have achieved power conversion efficiencies exceeding 27%, rivaling crystalline silicon photovoltaics. Among device architectures, the inverted p-i-n configuration offers excellent reproducibility, negligible hysteresis, and compatibility with silicon bottom cells, making it promising for scalable tandem integration. As the field shifts toward industrial viability, key challenges focus on interfacial stability, process reproducibility, and large-area manufacturability. The buried interface between the perovskite absorber and charge transport layers dictates nucleation, crystallization, charge extraction, and recombination dynamics. Imperfect interfacial contact or mismatched energy alignment leads to trap states, increased nonradiative recombination, and rapid degradation. Self-assembled monolayers (SAMs) have revolutionized interface control, offering tunable energy levels, minimized parasitic absorption, and reduced defects. However, SAM-based interfaces face scale-up challenges due to molecular aggregation, incomplete coverage, and hydrophobicity, causing nonuniform nucleation and pinhole formation. Co-assembled monolayers (Co-SAMs) have been explored but remain limited to small areas. Addressing this bottleneck, Zhao et al. proposed a 'SAM-in-matrix' strategy embedding SAM molecules within a tris(pentafluorophenyl)borane (BCF) matrix. This BCF framework disrupts π–π stacking, suppressing aggregation and producing an amorphous, uniform, and highly wettable hole transport layer, potentially enabling scalable manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4274-x
The escalating power density of electronic devices necessitates effective visible-light shielding in advanced packaging to ensure circuit security and long-term reliability. Photosensitive polyimides (PSPI) serve dual roles as photodefinable dielectrics and structural layers, but intrinsically black PSPI (B-PSPI) suffer from competitive ultraviolet (UV) absorption between chromophores and photosensitive moieties, limiting co-optimization of deep visible-light blocking and lithographic resolution. Here, we report a main-/side-chain spatial decoupling strategy to synthesize a novel B-PSPI. By polymerizing pyromellitic dianhydride with a main-chain coloring monomer (4,4'-diaminodiphenylamine) and a side-chain photosensitive monomer (1,4-dihydropyridine-functionalized diamine), the monomer stoichiometric ratio is precisely engineered. This design spatially isolates functional groups and enhances charge transfer, yielding exceptional visible-light shielding (CIE L* index of 21.39, cut-off wavelength ≈ 555 nm) with good lithographic sensitivity. UV exposure triggers in situ generation of coordination sites from photosensitive groups, anchoring active metal species for electroless copper plating. This enables direct additive fabrication of fine copper lines (40/80 μm line width/spacing) with robust Cu/B-PSPI interfacial adhesion of 16.6 MPa. This work provides a robust molecular design paradigm for B-PSPI, integrating superior optical shielding and surface metallization for high-density interconnect applications.