SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024092906
Microplastic pollution in rivers and lakes has become a research hotspot, yet studies in Anhui Province have predominantly focused on northern and central regions, leaving southern Anhui under-investigated. This study addresses that gap by examining the Xin'an River in Huangshan City, a typical river in southern Anhui. Surface water and sediment samples were collected in December 2023. In surface water, microplastic concentrations ranged from 350 to 3700 n·m−3, with particles of 0–0.5 mm dominating (33.93%). Fibrous shapes were most prevalent (59.83%), and colored particles accounted for 50.27%. In sediments, concentrations ranged from 25 to 200 n·kg−1, with 0–0.5 mm particles again dominant (49.63%). Fibers comprised 47.08% of sediment microplastics, and white particles accounted for 34.74%. Polymer analysis identified polyethylene terephthalate (PET) as the most abundant material (36.61%), followed by polyamide (PA) (23.22%). Source analysis suggests that fibrous microplastics originate primarily from fiber-based products such as clothing, home textiles, and fishing nets. These findings provide essential baseline data for water resource management, pollution assessment, and ecological remediation of the Xin'an River.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61102-X
Silicon-carbon composites prepared by chemical vapor deposition (CVD) are promising anode materials for high-energy-density lithium-ion batteries. However, the influence of the pore structure of the porous carbon (PC) carrier on silicon deposition behavior, and the impact of surface silicon on cycling stability, remain unclear. This study systematically investigates these effects using nitrogen adsorption-desorption analysis, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Porous carbons with varying pore architectures were synthesized by adjusting KOH activator ratios. Results show that increased micropore volume facilitates higher silicon mass loading, but also elevates the content of surface floating silicon due to greater silane exposure. Moderately increasing mesopores in high-microporosity carbon promotes deeper silicon deposition, reducing surface floating silicon. Excessive surface floating silicon hinders lithium-ion diffusion kinetics, leading to accumulation of active lithium, accelerated SEI growth, and electrode degradation. Electrochemical testing reveals that the optimized silicon-carbon composite maintains a high specific capacity of 693.1 mAh/g after 150 cycles at 0.5 C (900 mA/g). This work provides new insights into the development and failure mechanisms of CVD-derived silicon-carbon composite anodes, emphasizing the critical role of pore structure in mitigating surface silicon and enhancing cycling stability.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605020
To address the high CO2 emission proportion in the industrial sector, distillers' grain waste was converted into biochar for CO2 adsorption from flue gas. Raw biochar suffers from weak pore adsorption and poor selectivity at elevated temperatures. This study employed ash self-templating and particle self-assembly to create hierarchical pores and simultaneously load amine groups onto distillers' grains-derived biochar, yielding amine-functionalized hierarchical porous carbon spheres. The amine loading significantly increased, providing more CO2 adsorption sites, while retaining macroporosity (total pore volume 0.0030–0.0066 cm3/g after amine loading), which enhanced morphological stability and CO2 mass transfer. The optimal sample, 0.2PW-K-CNF-PEI, exhibited a CO2 adsorption capacity of 1.03 mmol/g at 100 °C, a CO2 diffusion coefficient of 0.0495 min−1, and a selective adsorption capacity of 44 mg/g at 80 °C. This work offers a solution for valorizing distillers' grain by-products and capturing CO2 from low-temperature flue gas.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606004
To identify optimal watershed remediation pathways under environmental and economic dimensions, an integrated environmental-economic impact assessment framework combining life cycle assessment (LCA) and life cycle costing (LCC) based on openLCA was established, using 1 m³ of treated wastewater as the functional unit. This framework comprehensively evaluated the environmental impacts and economic costs of three ecological buffer measures—constructed wetlands, ecological intercepting ditches, and vegetation restoration projects—in non-point source pollution control. The results indicated that constructed wetlands offer the optimal environmental-economic profile, featuring the lowest comprehensive cost (¥1.01 yuan/m³) and the lowest load across most environmental impact categories, with only slightly higher land resource consumption intensity. Ecological intercepting ditches exhibited higher impacts in areas such as metal resource consumption due to the use of rebars and base fertilizer inputs, resulting in a moderate comprehensive cost (¥1.57 yuan/m³). Vegetation restoration projects incurred the highest comprehensive cost (¥61.14 yuan/m³) and produced the most significant environmental impacts, with elevated indicators such as human carcinogenic toxicity. This primarily stemmed from the extensive use of concrete grass pavers and base fertilizer in rural river sections. These findings provide quantitative references for environmental-economic integrated evaluation and decision-making regarding ecological buffer zone engineering schemes in similar watersheds.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026020207
Although the production and use of hexabromocyclododecanes (HBCDs) have been completely banned in China since December 2021, historical production activities may still leave high-concentration residual contamination in localized areas. This study investigated a typical legacy site of historical HBCDs production in eastern China. Surface and core soil samples were systematically collected both inside and outside the former plant area to characterize the occurrence, spatial distribution, and environmental burden of HBCDs, and to evaluate associated human health risks. Results showed that HBCD concentrations in soils outside the plant area ranged from below detection limit to 6.90×10² ng·g⁻¹ dw, while those inside the plant area were substantially higher, reaching up to 1.18×10⁶ ng·g⁻¹ dw. γ-HBCD was the dominant isomer; however, its relative abundance was lower than that reported in commercial HBCD mixtures and in previous studies conducted near production facilities. Outside the plant, HBCDs concentrations in soil generally decreased with increasing distance from the site, yet remained detectable at a distance of approximately 10 km (15.2 ng·g⁻¹ dw). Within the plant area, HBCDs concentrations in soil cores decreased with depth, declining from 1.08×10⁴–1.18×10⁶ ng·g⁻¹ dw in surface soils to 1.05–93.5 ng·g⁻¹ dw at depths of about 4 m. Analysis of the relative cumulative environmental burden indicated that although HBCDs loads were highest in the near-source area, they gradually accumulated over a broader spatial scale. Approximately 23.7%, 40.1%, 60.0%, and 87.1% of the total estimated burden accumulated within 2 km, 2.81 km, 4 km, and 6 km from the site, respectively. Health risk assessment indicated that oral ingestion of soil was the primary exposure pathway for different populations. Localized high-contamination zones within the plant area contributed significantly to non-carcinogenic risks, while overall risks for children outside the plant area were at acceptable levels.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607019
This study investigated the effects of biochar on volatile fatty acids (VFAs) production, biogas composition, physicochemical properties of the fermentation broth, and microbial community structure through batch anaerobic fermentation experiments using food waste as the substrate. The results demonstrated that the addition of biochar (1 g/L) significantly enhanced VFAs production, with the total VFAs concentration reaching 2150 mg/L in the biochar group, which was 30.2% higher than that of the control group (1651 mg/L). Acetic acid, propionic acid, and butyric acid were identified as the primary VFAs components. In the fermentation system, biochar exhibited a notable pH-buffering effect, stabilizing the fermentation environment. Additionally, its porous structure adsorbed ions during the fermentation process, resulting in a slightly lower electrical conductivity compared to the control group. Microbial community analysis revealed that biochar addition enriched key acidogenic bacteria, such as Defluviitoga and norank_f__Family_XI, optimizing the microbial community structure, and thereby facilitating organic acid production. In summary, biochar effectively promoted the efficient accumulation of VFAs during anaerobic fermentation of food waste by improving the fermentation microenvironment, enhancing system buffering capacity, and regulating microbial community composition. These findings provide theoretical support for sustainable enhancement of resource utilization of food waste.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3922-2
Photocatalytic reduction of CO2 to syngas (CO and H2) is pivotal for Fischer-Tropsch synthesis and carbon neutrality, yet suffers from rapid charge carrier recombination. Here, we report a solvent-induced defect engineering strategy to fabricate nitrogen vacancy (Nv)-modified Fe3O4 (Fe3O4-Nv-12h). Under visible light (λ ≥ 420 nm), Fe3O4-Nv-12h achieves a total syngas production rate of 43.55 mmol g−1 h−1 with a near 1:1 CO/H2 ratio, representing an 805.2-fold enhancement over pristine Fe3O4 and surpassing state-of-the-art systems. Electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS) confirm that Nv introduction modulates the electronic structure, acting as electron traps to suppress recombination and enhance charge transport. In situ Fourier transform infrared (FTIR) spectroscopy identifies *COOH and *CO as key intermediates for CO formation. This work establishes an effective nitrogen vacancy modification strategy for efficient photocatalytic CO2 conversion to syngas, offering new avenues for high-performance catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3964-5
The escalating demand for personalized thermal-moisture comfort, coupled with the high energy consumption of conventional heating and cooling systems and the imperative for low-carbon energy conservation, has driven the development of shape memory smart fabrics that respond to environmental changes. However, existing shape memory thermal-moisture management fabrics suffer from excessively high response temperatures, inadequate response performance, and suboptimal thermal-moisture management. In this work, a dual-network shape memory polymer (SMP) was synthesized, and its shape memory transition temperature was tuned to align with the human thermal comfort range. The polymer was processed into fibers and subsequently into twisted-coiled artificial muscles to enhance reversible strain. Woven with wool into a plain fabric, the resulting textile exhibits adaptive thermal-moisture management, achieving a warp reversible strain of up to 17.5%. At elevated temperatures, the fabric contracts, exhibiting an air permeability of 1546 mm/s and thermal conductivity of 0.0518 W/(m·K); at lower temperatures, it elongates, with air permeability of 1322 mm/s and thermal conductivity of 0.0426 W/(m·K), thereby realizing 'warm when cool and cool when hot' functionality. Compared with commercial wool fabrics, this smart fabric lowers the skin microenvironment temperature by 1.5 °C and offers an energy savings potential of approximately 222.58 MJ/m² per year in capital cities such as Beijing. This work provides a novel technical pathway and design approach for future personalized comfort and low-carbon, energy-saving textiles.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.