SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3697-8
Multi-site coupling is a promising strategy for developing highly efficient and CO-resistant hydrogen oxidation reaction (HOR) catalysts for proton exchange membrane fuel cells (PEMFCs). However, designing multifunctional synergistic schemes for single-atom sites remains a significant challenge. Herein, we propose a dual-template-confined oxophilic engineering strategy to construct well-dispersed iridium-nickel (IrNi) atomic dimers adjacent to IrNi nanoclusters on porous nitrogen-doped carbon (IrNi Dimer/NC1.8-PNC). The paired IrNi dimer features an asymmetric Ir-N3 configuration coordinated with heteroatomic Ni-N3O via an N-bridge. Remarkably, IrNi Dimer/NC1.8-PNC exhibits a ~23-fold enhancement in mass activity (4.36 A mg−1 Ir at 20 mV) and 5-fold longer stability compared to benchmarking Pt/C toward HOR, while achieving a high rated power density of 1.18 W cm−2 in PEMFC anode applications. Furthermore, IrNi Dimer/NC1.8-PNC demonstrates superior CO tolerance over monometallic Ir and Pt/C in both half-cell and full-cell devices. Combined experimental and density functional theory studies reveal that oxophilic Ni modulates the electronic environment of Ir through alloying and dimer interactions, thereby enhancing HOR activity. Importantly, the asymmetric IrNi dimer enables efficient CO* and OH* co-adsorption while facilitating CO2* desorption, synergistically mitigating CO poisoning and improving atom utilization efficiency. This work provides a design strategy and fundamental insights for multi-site synergistic catalysts in PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3711-8
Mechanoluminescent (ML) materials that emit light under mechanical stress are attracting growing attention for their potential in next-generation sensing, display, and energy-harvesting technologies. Among these, Mn/Cu-doped zinc sulfide (ZnS) has emerged as a leading candidate due to its bright emission, low activation threshold, and remarkable self-recovery over thousands of cycles. Despite these advantages, the fundamental mechanisms governing ML remain unresolved, with ongoing debate between two primary models: the piezoelectric effect and the triboelectric effect. The piezoelectric effect is generally associated with scenarios where ML materials emit light directly under external pressure and exhibit self-recoverable performance, whereas the triboelectric effect dominates when emission occurs at the interface of layered materials. Previous research on ZnS-based ML systems has focused on phase transitions from the sphalerite phase to the wurtzite phase, as the latter is widely recognized as critical for ML activity. A recent study published in Advanced Materials introduces a transformative approach that not only enhances ML performance but also provides new insights into its underlying mechanism. The authors demonstrate that controllable phase transitions can be used to tune and optimize ML properties in ZnS. For the first time, they report a gradual and reversible transition between hexagonal wurtzite (wt-ZnS) and cubic sphalerite (sp-ZnS) phases at room temperature using low uniaxial pressure in the range of 0–30 MPa, a striking departure from the extreme conditions traditionally required for such transformations. Applying modest pressure with a standard tableting machine converts wt-ZnS into sp-ZnS without the need for high-temperature or high-pressure environments, while subsequent thermal annealing reverses the process, enabling reversible structural cycling. High-resolution transmission electron microscopy reveals that this phase transition is mediated by dislocations: a 1/3⟨1120⟩ screw dislocation decomposes into two 30° Shockley partial dislocations, 1/3⟨1010⟩ and 1/3⟨0110⟩, whose glide converts portions of the wt-ZnS lattice into the sp-ZnS structure. These dislocation-driven rearrangements introduce stacking faults and localized lattice distortions that exert a profound influence on luminescence behavior. Under dynamic loading, charged dislocations facilitate carrier transport toward Mn2+ luminescent centers by altering the energy transfer pathways. Regions undergoing phase transition exhibit stronger mechanoluminescence due to an enhanced local piezoelectric field compared to areas without phase transition. The study further uncovers strikingly different responses for Mn and Cu dopants under pressure. For Mn-doped ZnS, ML intensity increases by up to 2.7 times at moderate pressures around 10 MPa, an enhancement attributed to stronger local piezoelectric fields and more efficient carrier transport. In contrast, Cu-doped ZnS exhibits pronounced ML quenching under similar conditions, underscoring the fundamentally different energy transfer pathways associated with these dopants. Pressure-thermal cycling enables tunable ML and photoluminescence (PL) properties, opening new opportunities for adaptive optical devices. The manuscript also reports on the ML behavior of Mn, Cu co-doped ZnS, which exhibits similar pressure-responsive characteristics to Cu-doped ZnS, but with the emission predominantly originating from Mn2+ centers. The authors propose a dislocation-mediated ML mechanism in which charged dislocations generate local electric fields that alter carrier migration and complexation. Under dynamic loading, the piezoelectric field in ZnS separates carriers, which become trapped at defect levels and subsequently recombine at luminescent centers, leading to light emission.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026021203
Neonicotinoid insecticides (NEOs) are widely used pesticides with residues entering the human body via multiple routes, posing potential health risks. Pregnant women are a sensitive population requiring investigation into NEO exposure effects. Based on the Jiashan Birth Cohort, this study measured 12 NEOs (9 parent compounds and 3 metabolites) and three oxidative stress biomarkers (8-iso-prostaglandin F2α, 8-iso-15(R)-prostaglandin F2α, and 8-hydroxy-deoxyguanosine) in urine from 917 pregnant women using liquid chromatography-triple quadrupole mass spectrometry. Demographic data were integrated to analyze exposure patterns and associations. Results showed at least one NEO detected in all samples; seven NEOs had detection rates >50%. Median creatinine-adjusted total concentration was 5.613 μg·g−1. Acetamiprid-N-desmethyl (N-dm-ACE) had the highest detection rate (98.59%) and largest concentration proportion (64.2%). Spearman correlation, multiple linear regression, and Bayesian kernel machine regression revealed positive associations between oxidative stress markers and NEO exposure. Specifically, 8-PGF and 15-PGF correlated positively with thiacloprid-amide (THI-amid) and dinotefuran (DIN); 8-OHdG correlated positively with thiamethoxam (THM) and sulfoxaflor (SFX). Health risk assessment indicated hazard quotients below 1 for all NEOs, suggesting low health risks. This study provides evidence linking NEO exposure to oxidative stress damage in pregnant women, informing risk assessment for sensitive populations.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051404
Rubber additives, such as 1,3-diphenylguanidine (DPG) and p-phenylenediamine antioxidants (PPDs), are widely used in the rubber industry and have been increasingly detected in aquatic environments. This study investigated the distribution characteristics and potential sources of seven typical rubber additives (DPG, 6PPD, IPPD, DPPD, CPPD, DNPD, and 77PD) and the transformation product 6PPD-Q in surface water of the Guangzhou section of the Pearl River, China. A total of 29 sampling sites were analyzed. Total concentrations of the target compounds ranged from 205 to 5400 ng·L−1, with a mean of (820±1100) ng·L−1. DPG was the dominant compound in both dissolved and particle phases, accounting for (99±1.9)% and (66±13)% of the total concentrations, respectively. Source analysis indicated that aquaculture, vessel navigation, agricultural runoff, and wastewater treatment plant discharges likely influence the occurrence of rubber additives in this river section. Risk quotient (RQ) assessment revealed that 6PPD-Q posed high ecological risk at all sampling sites (RQ > 1), while DPG exhibited moderate to high risk at most sites (RQ > 0.1). In contrast, 6PPD, IPPD, CPPD, and DPPD showed low ecological risk. These findings highlight the need for heightened attention to the ecological risks posed by 6PPD-Q and DPG in the Pearl River Basin and provide scientific data for pollution prevention and risk management.