Nano Research Energy•2026•DOI: 10.26599/NRE.2025.9120181
Solid-state lithium metal batteries (SLMBs) demand quasi-solid polymer electrolytes (QSSPEs) that simultaneously deliver high ionic conductivity, interfacial stability, and oxidative resistance. This study reports a QSSPE membrane (MP46) formulated with MG30:LiTFSI:succinonitrile at a 10:4:6 weight ratio, exhibiting a wide electrochemical window of 5.1 V. Complementary infrared spectroscopy, small-angle X-ray scattering, and electron microscopy reveal a hierarchical ionic conductive network consisting of sphere-like nanostructures embedded within microphase-segregated architectures. This morphology enhances lithium-ion transport while preserving mechanical integrity. The strong interfacial adhesion between MP46 and lithium metal enables stable lithium plating and stripping for over 800 h at 0.2 mA·cm–2, effectively mitigating dendrite formation. When paired with LiFePO4 and LiCoO2 cathodes, MP46 sustains prolonged cycling, retaining 80.1% capacity after 1400 cycles at 2 C and 92.1% after 200 cycles at 4.5 V, respectively. Pouch-type cells further demonstrate mechanical flexibility and operational safety under deformation. These results establish MP46 as a viable candidate for stable high-energy-density SLMBs, offering fundamental insights into the design of next-generation polymer electrolytes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3487-x
Continuous carbon fiber-reinforced ZrB2-SiC ceramic matrix composites are promising thermal protection materials for hypersonic vehicles and reusable spacecraft. Although injection-assisted vacuum impregnation (IVI) offers advantages such as shorter processing cycles, lower costs, and reduced fiber damage compared to conventional methods, phenolic/acetone-based IVI systems yield composites (designated as CPS) with limited ceramic contents. To address this, an aqueous slurry-based IVI approach was developed, producing composites designated as CHS. After a single IVI cycle, CHS achieved a ZrB2 phase volume fraction of 25 vol.%, 47% higher than CPS, while reducing processing time by 49%. After chemical vapor infiltration, CVI-CHS composite exhibited a room-temperature compressive strength of 106.78±10.53 MPa, representing a 28% improvement over CVI-CPS. Crack propagation analysis revealed discontinuous zigzag patterns under compression, dominated by fiber bridging and pull-out energy dissipation mechanisms. Flexural results revealed both composites retain considerable strength (111.15±12.46 and 83.15±12.03 MPa) along with low flexural modulus (13.00±2.41 and 13.52±6.99 GPa) and high strain tolerance (1.32%±0.018% and 1.07%±0.34%). It is attributed to the anisotropy of fiber preforms and the elastic modulus mismatch among different phases, which hindered effective constraint of fibers by the matrix and, in turn, facilitated mitigation of stress concentration. Additionally, CVI-CPS demonstrated superior X-band electromagnetic interference (EMI) shielding (34–36 dB) compared to CVI-CHS (22–27 dB), resulting from synergistic effects between pyrolitic and deposited carbon in the matrix of the former. Both composites showed enhanced EMI shielding efficiency with increasing temperature up to 600°C. This eco-friendly aqueous IVI strategy enables high-performance, cost-effective thermal protection materials with higher ceramic loading and tunable multifunctional properties.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509095
Biotrickling filtration (BTF) is a promising technology for treating volatile organic compounds (VOCs), but its application to hydrophobic alkanes like isohexane is hindered by mass transfer limitations, low degradation efficiency, and high operational costs. To address these bottlenecks, this study developed composite fillers by incorporating biochars derived from coffee grounds (CG), coconut shells (CS), corn cobs (CC), and activated carbon (AC) into a polyvinyl alcohol-sodium alginate (PVA-SA) hydrogel matrix. The fillers were systematically characterized for water retention, pore structure, surface functional groups, crystalline phase, and acid-base resistance. Adsorption capacity, biofilm formation, and isohexane degradation were evaluated using the strain Rhodococcus ruber ZYH-ZY. Among the composites, CG@PVA-SA exhibited superior performance: water retention of 358 mg·g−1 (vs. 280 mg·g−1 for control), enhanced mesoporosity (specific surface area 4.77 m2·g−1, pore volume 11.46 cm3·kg−1, 10–30% higher than control), and robust acid-base stability (mass loss 21.37% at pH 2 and 31.98% at pH 10). Its saturated adsorption capacity reached 201.02 mg·kg−1 (vs. 114.24 mg·kg−1 for control), and it promoted bacterial colonization with a survival rate of 79.0% (vs. 37.2% for control). Static degradation tests showed 96.59% removal of 10 μL isohexane within 24 h. The abundant polar functional groups and suitable mesoporous structure of coffee ground biochar synergized with the PVA-SA matrix, enhancing water retention, mass transfer, and microbial colonization, thereby significantly improving isohexane purification. CG@PVA-SA is an ideal filler for BTF treatment of alkane VOCs, offering a cost-effective and efficient solution for industrial VOC control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3790-5
Near-infrared (NIR) phosphors with high quantum efficiency (QE) and thermal robustness are critical for phosphor-converted light-emitting diodes (pc-LEDs). Here, a Cr3+-activated Lu2BaAl4SiO12 (LBASO) garnet phosphor is engineered via chemical unit cosubstitution of [Ba2+-Si4+] for [Lu3+-Al3+] in Lu3Al5O12 (LuAG), inducing a strong crystal field that yields NIR emission at 705 nm. The optimized LBASO:0.07Cr3+ exhibits an internal quantum efficiency (IQE) of 84.82% and external quantum efficiency (EQE) of 46.02%. Notably, it demonstrates anti-thermal quenching (ATQ) with 126.03% of its initial intensity at 498 K under 442 nm excitation, attributed to a wide band gap, weak electron-phonon coupling, defect trap energy levels, high structural rigidity, and optimized electron population distribution. A NIR pc-LED fabricated with this phosphor achieves an output power of 134.99 mW and photoelectric conversion efficiency of 11.4% at 100 mA drive current. These results underscore the potential of LBASO:Cr3+ for applications in plant lighting, night vision, and nondestructive analysis.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607020
Kitchen waste (KW) and excess sludge (ES) are urban biowastes with resource recovery potential, commonly treated via anaerobic digestion (AD) for methane production. However, KW mono-digestion suffers from acidification, while ES yields low methane. This study employed semi-continuous reactors to simulate practical AD, co-digesting KW and ES at a 4:1 volatile solids ratio with biochar addition (0.5, 1.0, 2.5, 5.0, 10.0 g/L). The optimal biochar dosage was 2.5 g/L, achieving cumulative biogas and methane volumes of 17.53 L and 11.63 L, respectively, representing 42.10% and 39.47% increases over the biochar-free control, and 34.45% and 43.30% enhancements relative to thermally hydrolyzed sludge. The methanogenic lag phase decreased from (5.65±0.11) d to (4.33±0.12) d. Process stability improved, with average volatile fatty acids (VFAs) during stable operation dropping from 1708 mg/L to 1033 mg/L. Microbial analysis revealed enhanced diversity and enrichment of Synergistetes and Syntrophomonas, indicating direct interspecies electron transfer (DIET) promotion. Biochar at low concentrations enhances AD by immobilizing microbes and facilitating electron transfer, while high concentrations (10 g/L) may inhibit methanogenesis due to fatty acid degradation blockage, yet total methane production remained above control. These findings demonstrate that biochar addition at 2.5 g/L effectively enhances methane production and process stability in KW-ES co-digestion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4033-1
Photodetectors are critical components in modern optoelectronic systems, underpinning applications in optical communication, low-altitude economy, environmental monitoring, and national defense. Layered two-dimensional (2D) materials such as MoS2, WS2, black phosphorus (BP), and ReS2 have attracted extensive attention due to their remarkable electronic and optical properties, including facile mechanical exfoliation and tunable characteristics via thickness engineering. The absence of dangling bonds enables the construction of van der Waals (vdW) heterostructures free from lattice-matching constraints, promoting efficient charge transport, enhanced light absorption, and suppressed dark current. Among layered materials, semimetals such as graphene, PdTe2, MoTe2, and TaIrTe4 exhibit narrow or zero bandgaps, enabling ultrabroadband spectral responses from ultraviolet (UV) to terahertz (THz). ZrTe3, a layered gapless semimetal, demonstrates pronounced carrier transport features, including robust excitons and ultrafast carrier relaxation times, making it an ideal candidate for photodetection. However, pure ZrTe3-based photodetectors suffer from substantial dark current due to the absence of an energy bandgap, degrading signal-to-noise ratio and specific detectivity (D*). This work reports a high-performance broadband photodetector based on a ZrTe3/CuInP2Se6 heterostructure. By exploiting an asymmetric contact configuration that introduces a Schottky barrier, the device effectively suppresses dark current while enhancing photoresponse. The photodetector exhibits broad spectral sensitivity from UV to near-infrared (355–1177 nm), microsecond-level response speed, and high responsivity and specific detectivity. Beyond conventional photodetection, an optoelectronic information encryption-decryption application is demonstrated, where modulated light and bias voltage serve as dual input channels to encode and decode ASCII signals. This study resolves the challenge of high dark current in semimetal-based photodetectors and introduces a multifunctional platform for secure optoelectronic communication, highlighting the potential of ZrTe3 for next-generation photonic and quantum information technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3924-x
Metal halide perovskite solar cells (PSCs) have achieved power conversion efficiencies exceeding 27%, rivaling crystalline silicon photovoltaics. Among device architectures, the inverted p-i-n configuration offers excellent reproducibility, negligible hysteresis, and compatibility with silicon bottom cells, making it promising for scalable tandem integration. As the field shifts toward industrial viability, key challenges focus on interfacial stability, process reproducibility, and large-area manufacturability. The buried interface between the perovskite absorber and charge transport layers dictates nucleation, crystallization, charge extraction, and recombination dynamics. Imperfect interfacial contact or mismatched energy alignment leads to trap states, increased nonradiative recombination, and rapid degradation. Self-assembled monolayers (SAMs) have revolutionized interface control, offering tunable energy levels, minimized parasitic absorption, and reduced defects. However, SAM-based interfaces face scale-up challenges due to molecular aggregation, incomplete coverage, and hydrophobicity, causing nonuniform nucleation and pinhole formation. Co-assembled monolayers (Co-SAMs) have been explored but remain limited to small areas. Addressing this bottleneck, Zhao et al. proposed a 'SAM-in-matrix' strategy embedding SAM molecules within a tris(pentafluorophenyl)borane (BCF) matrix. This BCF framework disrupts π–π stacking, suppressing aggregation and producing an amorphous, uniform, and highly wettable hole transport layer, potentially enabling scalable manufacturing.