SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3682-6
Metal single-atoms with optimized coordination structure on highly accessible substrate can maximize the metal utilization efficiency along with enhancing catalytic activities. Herein, axial nitrogen-coordinated Fe-N5 sites on N-doped carbon (denoted as FeN5@N-C) hollow microplates are fabricated via a unique Fe3+-chelated polydopamine assisted hollowing strategy using ZIF-L microplates as multifunctional templates. Due to the powerful chelating and adhesive ability of polydopamine, this hollow-carbon strategy can be extended to fabricate single-atom Fe-N-C hollow structures with different shapes and encapsulate other transition-metal single atoms (Ni, Co, Mn, and Cu) into the N-doped carbon hollow microplates. The FeN5@N-C hollow microplates exhibit outstanding oxygen reduction reaction (ORR) capability with an impressive half-wave potential of 0.93 V vs. reversible hydrogen electrode and high stability, which can serve as air-cathode catalysts for high-performance Zn-air batteries with high peak power density of 225.3 mW cm−2 and stable cyclability of up to 400 h. Comprehensive analysis and theoretical calculations elucidate that axial nitrogen coordination in Fe-N5 catalytic sites, unlike the planar Fe-N4 configuration, can compete well with the bonding of OH* through additional 3d-2p orbital hybridization, thereby giving moderate bonding strength to enhance the ORR activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3869-7
Iontronic capacitive pressure sensors (ICPSs) are pivotal for wearable technology, yet their performance is constrained by an inherent trade-off between sensitivity and detection range. Here, we introduce a micro-electric double layer (micro-EDL) engineering strategy to overcome this limitation. This is realized through a nanocomposite dielectric where multi-walled carbon nanotubes (MWCNTs) form a percolated network, generating a dense array of pressure-responsive nano-capacitors. Synergistically integrating a hierarchical MoS2/NiCo-LDH electrode provides abundant pseudocapacitive interfaces. The resulting sensor exhibits an ultrahigh sensitivity of 67,095 kPa−1 at 1 kHz, a broad detection range up to 1.3 MPa, rapid response and recovery times of 4 ms and 5 ms, respectively, and outstanding durability exceeding 18,000 cycles. Practical validation demonstrates 100% classification accuracy in recognizing complex gestures and gait patterns, underscoring its real-world applicability. These findings establish micro-EDL engineering as a promising route for advancing next-generation iontronic devices, offering insights into their electrochemical mechanisms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3967-x
Metal-halide perovskites exhibit exceptional optical gain, narrow emission linewidths, and high emission efficiency, positioning them as promising candidates for next-generation lasers. Thermal evaporation, a mature semiconductor fabrication technique, offers scalability, yet monitoring phase distribution during deposition remains challenging. This study systematically investigates and regulates thermally evaporated FAxCs0.8PbBr3 perovskite films by tuning formamidinium (FA) content to optimize phase distribution. At intermediate FA content, films achieve a balanced distribution of n=2 to n=5 quantum-well phases, facilitating ultrafast carrier transfer (<0.31 ps) and suppressing nonradiative recombination. FA+ actively incorporates as an A-site cation, promoting ordered crystallization and reducing defect densities. The optimized films exhibit a net modal gain of 1041 cm−1 and a gain lifetime of 129 ps. Benefiting from efficient internal scattering, the threshold for cavity-free random lasing is reduced to below 5 μJ/cm2 at room temperature. The low spatial coherence of random lasing enables speckle-free imaging with a speckle contrast as low as 0.011 and improved contrast-to-noise ratios across all spatial frequencies. This work provides a scalable strategy for perovskite composition-phase engineering, advancing speckle-free laser imaging systems compatible with semiconductor-grade, large-area manufacturing.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041805
Selenium (Se) is an essential trace element for mammals, yet no universally applicable method exists for assessing soil Se bioavailability. This study validated the feasibility of diffusive gradients in thin-films (DGT) technology for accurately evaluating Se bioavailability in paddy soils under natural conditions, and analyzed Se migration in the soil-plant system, soil kinetic characteristics, and the influence of physicochemical properties on Se bioavailability. Rice plants and corresponding rhizosphere soil samples were collected and analyzed using three traditional extraction methods alongside DGT. Results showed that 96.7% of soil samples and 66.7% of rice samples met the selenium-rich standard, and Se content measured by DGT most accurately reflected soil Se bioavailability. The bioconcentration factor (BCF) of different rice plant parts indicated generally low Se enrichment in grains, with primary enrichment in rice roots. Correlation analysis revealed that adjustments in soil pH, organic matter (SOM), cation exchange capacity (CEC), and sulfur (S) content could effectively improve soil Se bioavailability. These findings underscore DGT's superiority over conventional extraction methods for predicting Se uptake, offering a robust tool for managing selenium-rich agricultural resources.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608023
Zinc-containing steel dust sludge, a by-product of steelmaking, contains high levels of chlorine (Cl) along with valuable metals such as Fe, Zn, K, and Na. When recycled into the steel production process, Cl accumulates, causing sintering instability and severe corrosion of blast furnace linings. This study investigated water leaching for Cl removal from zinc-containing steel dust sludge. Under optimal conditions (liquid-to-solid ratio 5 mL/g, temperature 70 °C, time 60 min, rotation speed 160 r/min), the Cl leaching rate reached 87%. Furthermore, a three-stage countercurrent water washing process at a liquid-to-solid ratio of 6 mL/g and room temperature for 45 min achieved a Cl leaching rate exceeding 90%. The water washing also reduced the leaching toxicity of metals in the sludge to a certain extent. Characterization via XRD, SEM, FT-IR, and XPS revealed that water washing primarily dissolved soluble chlorides (NaCl, KCl, etc.), increasing the specific surface area from 2.71 to 10.11 m²/g and average pore size from 12.83 to 16.29 nm. These findings provide theoretical and technical support for efficient Cl removal from zinc-containing steel dust sludge, facilitating its safe resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4067-4
Confined growth of metal halide perovskite quantum dots (QDs) in porous matrices yields improved stability and sensitivity for their implementation in luminescent chemical sensing applications. Here, we realized the synthesis of highly stable (water, photo, and thermal) and luminescent CsPbX3 QDs within nanoporous glass (NG). This is achieved by a nano-confined aqueous synthesis of CsPbBr3 QDs in Pb-anchored NG. Benefiting from strong Pb–O–Si chemical bonding between the perovskite QDs and the NG matrix, the stability of the encapsulated perovskite QDs is significantly enhanced. The emission of the perovskite NG can be tuned from 440 to 760 nm. By integrating green- and red-emitting perovskite NG onto a blue LED chip, stable WLEDs were successfully fabricated. This facile approach enables the integration of ultra-stable perovskite QDs within transparent porous monoliths toward diverse luminescent chemical sensing applications.