SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3704-0
The escalating demand for energy storage systems capable of delivering high energy density alongside ultrafast charging and discharging has exposed the limitations of conventional lithium-ion batteries (LIBs), particularly in applications such as electric air vehicles, portable medical devices, and grid-scale storage. Organic cathode materials offer tunable molecular design but suffer from sluggish ion diffusion kinetics, especially under high-rate and low-temperature conditions. This study introduces a 2D vertically ladder-like polymer (2DVLP) synthesized from tribenzoquinoline tribenzoquinone (TTQ) via a 2D polymerization strategy. The polymer features a layered nanosheet structure with densely distributed carbonyl (C=O) redox-active sites serving as Li+ storage centers. Interlayer micropores (0.4–2.0 nm) and structural defects facilitate vertical Li+ diffusion, while weak van der Waals interlayer interactions (no π–π stacking) enable horizontal Li+ intercalation. Coin-type half-cells using 2DVLP cathodes demonstrated outstanding room-temperature performance: 2DVLP-1 and 2DVLP-2 achieved specific capacities of 302 and 291 mAh g−1 at low current densities, respectively. The cross-flow design—combining vertical and horizontal ion transport pathways—effectively mitigates concentration polarization, enabling ultrafast charging. This work provides a scalable strategy for developing high-power organic cathodes, addressing critical bottlenecks in fast-charging energy storage.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024121201
A method for the simultaneous determination of 19 sulfonamide antibiotics in environmental aqueous samples was developed by integrating solid-phase extraction (SPE) and gel permeation chromatography (GPC) with ultra-performance liquid chromatography–triple quadrupole mass spectrometry (UPLC-MS/MS). Aqueous samples were filtered through 0.45 μm membranes, adjusted to pH 6, and treated with Na2EDTA at 2.5 mg·L−1 to mitigate matrix effects. Analytes were enriched on Oasis HLB cartridges, purified by GPC, and separated on a Hypersil GOLD C18 column (2.1 mm ID × 100 mm, 1.9 μm) using gradient elution with 0.05% (V/V) formic acid in water and methanol. Detection was performed in multiple reaction monitoring (MRM) mode with internal standard quantification. Under optimal conditions, limits of detection (LOD) and quantification (LOQ) ranged from 0.7–4.4 ng·L−1 and 2.8–17.6 ng·L−1, respectively. Recoveries from spiked real samples at 10, 200, and 400 ng·L−1 were 44.5%–102%, 47.7%–97.5%, and 51.4%–115%, with relative standard deviations (RSDs) of 1.8%–10%, 0.64%–5.9%, and 0.71%–4.6%, respectively. The method was applied to three surface waters and three municipal wastewater treatment plant effluents, detecting five sulfonamides at concentrations ranging from 1.82 to 3864 ng·L−1. The combined SPE-GPC cleanup effectively reduced matrix suppression, offering high sensitivity, precision, and robustness for routine monitoring of sulfonamide antibiotics in environmental waters.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604018
To address the issues of high air volume and unorganized emissions of waste gas in semi-steel vulcanization production lines, a combined approach of experimental testing and numerical simulation was employed to study the diffusion characteristics of VOCs-containing waste gas and the air volume of the collection system. The structure of the semi-enclosed hood was optimized, and pipe diameters were adjusted to achieve negative pressure balance, enabling efficient waste gas collection. Results showed that toluene concentration distributions from numerical simulation were largely consistent with experimental measurements, with a maximum average error of -3.9%. Existing hood inlet wind speeds ranged from 0.04 to 0.2 m/s, indicating uneven distribution. Under calm wind conditions, toluene diffusion in enclosed and semi-enclosed hoods was similar, with concentrations of 248 mg/m³ and 115 mg/m³, respectively, and deposition observed in trenches. For a single vulcanizer, at a design air volume of 2700 m³/h, the enclosed hood achieved a toluene concentration of 80 mg/m³ versus 63 mg/m³ for the semi-enclosed hood, demonstrating superior capture of hot fumes. Optimizing the semi-enclosed hood with soft curtains and a height of 1200 mm, at a total design air volume of 1.0×10⁵ m³/h, yielded an average hood inlet velocity of 0.35 m/s but still uneven distribution. Adding 900 mm gradual reducers and adjusting branch pipe diameters resulted in total air volume deviations of -0.44% and 0.38% for branches I and II, respectively, with individual hood deviations below 10%. This achieved negative pressure balance, effective collection, and improved workshop hygiene.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60627-X
This study systematically investigates the cyclization reaction mechanisms between n-C4H3 (1-buten-3-yn-1-yl) and i-C4H3 (2-buten-3-yn-1-yl) radicals with acetylene (C2H2) using density functional theory (DFT) and transition state theory (TST). The results reveal that the reaction of n-C4H3 with acetylene proceeds via a radical chain mechanism through an addition-cyclization pathway, yielding phenyl (six-membered ring), fulvenyl (five-membered ring), and four-membered ring intermediates. The product formation rates follow the order: fulvenyl (five-membered ring) > phenyl (six-membered ring) > four-membered ring. For i-C4H3, the intermediate structures depend on the carbon position of i-C4H3 where acetylene addition occurs: addition at the C2 position predominantly generates fulvenyl (five-membered ring) as the primary product, whereas addition at the C4 position may lead to phenyl (six-membered ring), fulvenyl (five-membered ring), or four-membered ring intermediates, with the four-membered ring forming most rapidly and the six-membered ring the slowest. Theoretical analyses demonstrate that the selectivity of reaction pathways is primarily governed by structural differences between the isomers. This work provides atomic-scale insights into the cyclization processes between acetylene and C4H3 species, establishing a foundation for refining models of soot precursor formation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010201
The Guanzhong region, traversed by the Wei River Basin, is one of the most industrially, agriculturally, and medically advanced and densely populated areas in Northwest China, has seen increasing attention paid to the pollution of perfluoroalkyl substances (PFASs) in its surface water environment. This study systematically investigated the pollution characteristics of PFASs in the surface water of this region and their ecological and health risks. By optimizing the online solid-phase extraction-liquid chromatography-tandem quadrupole mass spectrometry (Online SPE-LC/MS/MS), efficient detection of 19 PFASs was achieved, with the method detection limits ranging from 0.2 ng·L−1 to 0.3 ng·L−1, linear correlation coefficients all ≥ 0.990, and spiked recoveries between 75.2% and 130.0%. Monitoring data indicated that PFBA, PFPeA, PFHxA and PFOS, short-chain perfluorinated compounds, were the main pollutants in this region, with high detection frequencies and concentrations, but the overall content was lower than that in most areas of China. The concentrations of PFASs in surface water showed significant seasonal variations, with the highest concentrations during the dry season (∑19PFASs:126.1 — 2584.3 ng·L−1), followed by the normal season (∑19PFASs:3.5—3567.6 ng·L−1), and the lowest during the wet season (∑19PFASs:26.3—294.6 ng·L−1). Ecological risk assessment showed that, except for PFDoDA in the dry season, the ecological risk quotient (RQ) of all other PFASs was < 1. Although the water of the Wei River is not used as direct drinking water, health risk assessment indicated that all PFASs posed low risks, with only PFOA and PFOS showing potential risks (HR > 0.1) to adults and children at some sites during dry/normal seasons. This study provides a scientific basis for PFASs pollution control in the Wei River Basin.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3986-2
Organic/molecular ferroelectrics exhibiting spontaneous polarization have attracted increasing attention due to their flexibility, light weight, low-temperature processability, environmental friendliness, and biocompatibility. Among them, organic donor-acceptor cocrystals, self-assembled from two or more components, offer new insights into ferroelectricity. This review systematically examines recent progress in organic donor-acceptor cocrystal ferroelectrics, focusing on microscopic origins of ferroelectricity, structure modulation strategies, and underlying mechanisms. Ferroelectric origin mechanisms, including intermolecular charge transfer, proton transfer, and order-disorder transitions, are analyzed in detail. Structure-property relationships in crystal engineering are summarized, and recent advances in theoretical simulations, experimental characterization techniques, and practical applications are introduced. Finally, current challenges and future research perspectives are outlined. The review highlights that weak intermolecular interactions often lead to low Curie temperatures (Tc), limiting practical applications. Strategies to enhance Tc involve introducing stronger molecular interactions to increase transition energy barriers. Notably, room-temperature ferroelectricity in organic cocrystals has been achieved, as demonstrated by Wiscons et al. (Angew Chem Int Ed, 2018, 57: 9044–9047). The review underscores the potential of organic cocrystal ferroelectrics for flexible and wearable electronics, while addressing the need for higher Tc and robust switching performance.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60659-7
Coal gasification fine slag (CGFS), a solid waste from entrained-flow coal gasification, is characterized by fine particles and high silicon and aluminum content. This study proposes a simple and economical hydrothermal synthesis of ZSM-5 molecular sieve using CGFS as raw material. Impurities were removed by acid washing, followed by alkaline extraction of silicon and aluminum species. The extracted Si-Al precursors were crystallized hydrothermally at 170 °C for 48 h, yielding ZSM-5 with a high specific surface area of 358 m2/g. Adsorption experiments showed that the synthesized ZSM-5 exhibited excellent Pb2+ removal performance: at 25 °C, the removal efficiency for a 50 mg/L Pb2+ solution reached 83.7%, with an adsorption capacity of 104.625 mg/g under optimized conditions. The adsorption process is mainly governed by chemisorption mechanisms, including surface complexation, precipitation, and ion exchange. Thermodynamic analyses indicated that Pb2+ adsorption is spontaneous and endothermic, consistent with multilayer chemisorption. The synthesized ZSM-5 shows promising potential for application in the treatment of lead-containing wastewater, offering a high-value utilization route for coal-based solid waste.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032004
This study proposes an integrated source apportionment framework that synergistically integrates pollution source classification, atmospheric dispersion modeling, backward trajectory analysis, weighted trajectory clustering, and forward contribution estimation to accurately target peak reduction at localized air pollution hotspots. Applied at the County-Town Scale in Beijing, this method was employed to investigate pollution episodes at the Tongzhou Dongguan monitoring site. Source classification relied on a pollution fingerprint database and temporal concentration profiles, while local contributions were quantified through combined air quality modeling and monitoring data. Forward and backward trajectory analyses enabled the identification of potential source regions and key contributors. Results indicate that construction dust, road dust, and emissions from the catering industry were the dominant local sources, with construction and road dust contributing most prominently to PM2.5 concentrations. Furthermore, abnormal PM2.5 increases were closely linked to low boundary layer height, weak winds, and high humidity, emphasizing the role of meteorological conditions in pollution accumulation. The proposed framework proves effective in pinpointing local pollution sources and offers a scientific basis for targeted air quality management at finer spatial scales.