Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225213
Gas-liquid stirred tanks are widely used in oxidation, hydrogenation, and other chemical processes, where the gas dispersion state directly affects production efficiency. This study systematically investigated the effects of impeller type, impeller installation height, and rotational speed on gas-liquid dispersion in a stirred tank equipped with a porous tube sparger. Two typical impellers, a wide hydrofoil (WH) and a half-elliptical disk turbine (HEDT), were tested at various installation heights (L/D ratios) and gassing rates. The critical rotational speed for complete gas dispersion, agitation power consumption, and overall gas holdup were measured. Results showed that for both impellers, the critical Froude number (Fr) decreased significantly with increasing gas flow number (FlG). Under the same gassing rate, the HEDT impeller generally required a higher critical Fr and greater agitation power for complete dispersion compared to the WH impeller. Relative power demand (RPD) decreased as FlG increased, with a more pronounced decline at higher L/D ratios. At different impeller positions, the RPD of the HEDT impeller was higher than that of the WH impeller, indicating that the HEDT impeller's power was less affected by gas. Notably, the impeller installation height significantly influenced gas holdup and power consumption. When L/D = 0.75, higher gas holdup and lower power consumption were observed. This work provides crucial theoretical and data support for optimizing the design of gas-liquid stirred tanks with gas sparging, offering clear engineering value for enhancing mass transfer efficiency and energy-saving operation in chemical processes.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3808-x
The uncontrollable Zn dendrites and serious parasitic side reactions of the zinc anode severely impede the practical application of aqueous zinc-ion batteries. In this work, a unique strategy of multipoint solvate coordination center is proposed, which anchors Zn2+ and H2O with complex sites to establish an intermolecular connection within the asymmetric solvation structure. A hydrated deep eutectic electrolyte based on multi-site methylurea (MU) with Janus properties is developed, in which Zn2+ and H2O interact with MU through Lewis acid-base and hydrogen bonding interaction, and the regulated asymmetric solvation configuration can guide the (002)-ordered Zn deposition. Simultaneously, a small amount of polyethylene glycol (PEG, Mw=20000) can facilitate homogenous (002) Zn deposition by suppressing Zn2+ transfer kinetics. Benefiting from the rationally regulated solvation structure and PEG molecules adsorbed onto Zn anodes, the side reactions and Zn dendrites are significantly inhibited. As a result, the Zn||Zn symmetric cell delivers outstanding cycling performance over 3900 h (1 mA cm−2, 0.5 mA h cm−2). In addition, the Zn||V2O5 battery maintains 79.2% capacity retention after 1000 cycles at 1 A g−1. The results suggest a promising oriented regulation strategy for sustainable aqueous zinc-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3792-6
The rapid expansion of home-based digital health monitoring necessitates electrodes capable of simultaneous, accurate acquisition of electrophysiological signals and body temperature. Conventional single-function electrodes, including metal block, gel, and Ag/AgCl types, suffer from limitations such as restricted movement, skin irritation, signal degradation over time, and poor permeability for prolonged use. To overcome these challenges, we developed a low-cost, multifunctional flexible electrode enabling concurrent body temperature and electrophysiological signal monitoring without cross-interference. Body temperature is assessed via visual colorimetric evaluation and precisely measured using a custom smartphone application. The electrode features high air permeability, ultra-thin architecture, superior flexibility, antibacterial properties, and strong skin adhesion, while maintaining low interfacial impedance for stable, long-term acquisition of high-fidelity signals such as electrocardiography (ECG) and surface electromyography (sEMG). Integrated with a Raspberry Pi platform and a hybrid convolutional neural network-long short-term memory (CNN-LSTM) algorithm, the system achieves intelligent arrhythmia detection with 99.30% accuracy. This novel electrode provides a powerful tool for multifunctional sensing of temperature and physiological electrical signals, with significant potential for wearable physiological tracking applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4145-0
Conductive fibers face a fundamental trade-off between high electrical conductivity and substantial mechanical stretchability, which critically undermines their reliability under extreme or dynamic mechanical conditions. To overcome this challenge, we report a bio-inspired, hierarchically structured conductive fiber engineered by mimicking the parallel-fibril architecture and integrated matrix of skeletal muscle. This fiber is constructed from multiple parallel spandex yarns as the elastic core, a continuous liquid metal (LM) layer as the conductive pathway, and a composite waterborne polyurethane (WPU)/fluoropolymer (FP) sheath as the protective matrix. This unique architecture concurrently delivers exceptional stretchability (>3500%), high electrical conductivity (3.76 × 10^5 S m−1), and outstanding stability against water and mechanical abrasion. Leveraging its excellent conductivity and mechanical compliance, the fiber can be woven into textiles and function as a receiving coil for efficient wireless power transfer. Additionally, a twisted-pair capacitive strain sensor fabricated from this fiber demonstrates a broad, linear response up to 1000% strain. When integrated into garments, the sensor effectively monitors a wide range of physiological activities, from gross joint movements to subtle biological signals, including wrist pulse, vocal vibration, ballistocardiogram, and respiration. This work presents a conductive fiber that integrates high conductivity, ultra-stretchability, waterproofness, and long-term durability, offering a robust material platform and a scalable fabrication strategy for advancing all-weather health-monitoring systems, smart textiles, and next-generation wearable electronics.