SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3585-1
Semiconductor-based surface-enhanced Raman scattering (SERS) substrates have attracted significant attention due to their high uniformity, reproducibility, stability, and cost-effectiveness. However, the Raman enhancement in semiconductors primarily relies on the chemical mechanism (CM), which typically results in a lower enhancement capability compared to traditional noble metals. In this study, we developed a novel two-dimensional (2D) SERS substrate, Ag2Te nanosheets (NSs), synthesized through a simple one-step redox reaction utilizing 2D Te NSs as the template. The 2D Ag2Te NSs not only exhibit strong interfacial interactions with molecules, thereby supporting the CM, but also possess quasi-metallic properties with low resistivity (2.8 × 10−4 Ω cm) and high density of free electrons (4.15 × 10^22 cm−3), giving rise to a significant visible-region surface plasmon resonance (SPR) band and contributing to enormous electromagnetic mechanism (EM). By synergizing CM and EM, the 2D Ag2Te NSs SERS substrate achieved an ultra-low limit of detection (LOD) of 10−10 M with an enhancement factor (EF) of 2.6 × 10^7 for methylene blue (MB), outperforming most semiconductors, even rivaling noble metals. The quasi-metallic properties of 2D Ag2Te NSs also benefit their sensitivity to multiple molecules. The accuracy and reliability were demonstrated in real-sample detections with recoveries of 91.5%–108.3% for various target molecules. These excellent performances, combined with remarkable cost-effectiveness, demonstrate the potential of 2D Ag2Te NSs as a practical SERS substrate with broad applicability. Furthermore, the inherent structural simplicity of these nanosheets creates significant opportunities for further sophisticated nanostructural engineering to advance the SERS performance in the future.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3705-5
Biodegradable metals (BMs) are designed to corrode gradually in physiological environments, yet this corrosion can compromise their mechanical integrity, potentially causing premature implant failure. For emerging zinc-based alloys, the corrosion-mechanical property relationship remains inadequately characterized. This study systematically investigated the long-term corrosion-associated mechanical behavior of hot-extruded Zn-Cu and Zn-Cu-Fe alloys, promising Zn-based bio-metals, in comparison with pure Zn, under immersion degradation in Hank's solution. Electrochemical impedance spectroscopy and mechanical testing revealed that the evolving corrosion profile governs mechanical performance. Alloying with Cu and Fe mitigated corrosion's detrimental effects: grain refinement reduced localized corrosion susceptibility, while finely dispersed second phases acted as cathodic sites, promoting uniform corrosion. Additionally, Cu and Fe facilitated the formation of protective corrosion product layers, suppressing further matrix attack. Consequently, the overall reduced corrosion, particularly localized corrosion, lowered stress concentration susceptibility, delaying mechanical decline and preserving structural integrity. These findings elucidate the degradation-mechanical property correlation in Zn-based bio-metals and underscore critical considerations for developing new bio-metals for clinical translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3503-9
This correction addresses an image misuse in the original publication (Sci China Mater, 2025, 68(6): 2095, DOI: 10.1007/s40843-025-3311-6). Specifically, a fluorescent image in Fig. 4d, depicting live/dead cells after treatment with MPDA@TMZ without laser irradiation, was erroneously presented. The corrected Fig. 4 is provided, and the authors confirm that the results and conclusions of the original paper remain unaffected. The correction ensures the integrity of the reported data, particularly the cell viability and apoptosis assays. The study focuses on mesoporous bowl-shaped polydopamine (MPDA) nanoparticles co-loaded with temozolomide (TMZ) and indocyanine green (ICG) for synergistic glioblastoma therapy. The corrected figure includes CLSM images of G422 cells after incubation with various formulations (ICG, sPDA@ICG, mPDA@ICG, MPDA@ICG), cell viability curves, quantitative fluorescence intensity, live/dead staining, and apoptosis quantification. Statistical significance is denoted as ****p < 0.01. The correction maintains the scientific validity of the findings, which demonstrate the potential of MPDA-based nanoplatforms for combined chemo-photothermal therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3785-5
The effective separation and utilization of photo-generated carriers are critical for advancing photocatalysis, particularly in coupled reactions of H2 production and value-added chemical synthesis. Here, a sandwich-structured MnO2@ZnIn2S4@Ti3C2 hollow sphere was designed, with MnO2 and Ti3C2 loaded on the inner and outer surfaces of ZnIn2S4, respectively. MnO2 acts as an oxidation cocatalyst collecting photo-generated holes, while Ti3C2 serves as a reduction cocatalyst for electrons, promoting spatial separation of carriers and enabling spatially separated redox reactions. The hollow structure enhances light harvesting. The optimal catalyst achieves photocatalytic H2 production rate of 6.29 mmol g−1 h−1 and benzaldehyde production rate of 5.26 mmol g−1 h−1 from benzyl alcohol oxidation, significantly outperforming ZnIn2S4, MnO2@ZnIn2S4, and ZnIn2S4@Ti3C2. In situ irradiated X-ray photoelectron spectroscopy confirms effective carrier separation. In situ electron paramagnetic resonance and diffuse reflectance infrared Fourier transform spectroscopy reveal reaction intermediates. This work provides a strategy for designing efficient photocatalysts for coupled H2 production and selective oxidation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509020
The AAOA-MBR (anaerobic-anoxic-oxic-anoxic membrane bioreactor) process is widely used in municipal wastewater treatment, but its multi-stage internal recirculation complicates sludge retention time (SRT) and carbon source distribution. This study systematically regulated three reflux ratios (R1: membrane tank to oxic tank; R2: oxic tank to anoxic I tank; R3: anoxic II tank to anaerobic tank) in a pilot-scale system (0.24 m3·d−1) to reveal their effects on nutrient removal and membrane fouling. When R1:R2:R3 = 300%:200%:100%, effluent COD, TN, TP, and NH3-N met discharge standards. Reducing R1 and R2, thereby decreasing total reflux ratio from R=6 to R=3, shortened SRT, which suppressed nitrifier accumulation and increased effluent COD and TN, but decreased TP. High-throughput sequencing of anoxic I and oxic tanks showed that denitrifying bacteria (Thauera and Ottowia) relative abundances decreased from 0.68% to 0.42% and 0.51% to 0.24%, respectively, while the phosphorus-accumulating organism Candidatus_Accumulibacter increased from 0.78% to 1.12%, enhancing phosphorus removal. Additionally, lowering R1 to 200% caused sludge accumulation in the membrane tank, exacerbating membrane fouling. Thus, internal recirculation ratios must be adjusted based on influent characteristics to balance nutrient removal and membrane performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3870-9
High-purity (HP) alloys are critical for next-generation technologies requiring extreme reliability, yet trace impurities at parts-per-million levels can severely degrade mechanical properties, corrosion resistance, and long-term stability. This review comprehensively examines recent advances in HP alloy development, covering purification approaches, processing strategies, and performance optimization. It details how trace impurities influence microstructural evolution and material properties, and discusses techniques for achieving ultralow impurity levels, including vacuum melting, zone refining, and chemical vapor deposition. The review highlights impurity sensitivity across major alloy systems—such as aluminum, titanium, zirconium, copper, and steels—and summarizes strategies to mitigate impurity-induced degradation, including advanced alloy design, grain refinement, and surface treatments. Advanced characterization techniques for detecting and quantifying impurities are also outlined. The review emphasizes the essential role of HP alloys in advanced structural and functional materials, and identifies key challenges and future directions, including the need for standardized purity definitions and cost-effective purification methods. This synthesis provides a roadmap for researchers and engineers aiming to harness the full potential of high-purity alloys in demanding applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3906-2
Achieving flexible polymer-based organic afterglow materials with color-tunable and stimulus-responsive capabilities is significant in diverse optoelectronic fields, especially in next-generation wearable full-color display applications, yet remains a great challenge. Here, we report polymer-based dual-mode afterglow systems that realize long-lived color-tunable afterglow with full-color gamut of blue, green, orange, red, and even white-light emissions with ultralong lifetimes up to 2.42 s. This unique performance is enabled by a universal strategy of dual-mode afterglow-assisted Förster resonance energy transfer (FRET) that utilizes seconds-long dual-mode afterglow materials as energy donors and permits efficient synchronous transfer of singlet and triplet excitons from energy donors to the fluorescent dye acceptors. More impressively, the dual-mode afterglow-assisted FRET efficiency reaches up to 99%, with the lifetime of the energy acceptor reaching 1.55 s. Associated with the abundant hydrogen-bonding interactions within the polymer system, the doped afterglow films exhibit water/thermal stimulus responsiveness and recyclability. Furthermore, these full-color dual-mode afterglow materials are employed for multicolor screen-printing, optical anti-counterfeiting, and high-level information encryption, demonstrating considerable application potential in advanced anti-counterfeiting technologies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512064
With increasingly stringent discharge standards for fluoride-containing wastewater, there is an urgent need for cost-effective, easily operable adsorbents capable of rapid adsorption and separation for deep defluorination. In this study, a novel adsorbent, Ce-FMSY, was successfully prepared by co-precipitation of cerium (Ce) and Fe3O4 onto Y-type molecular sieve (MSY). The effects of Ce/Fe mass ratio, adsorption time, initial solution pH, and coexisting anions on adsorption performance were systematically investigated. Results showed that at a Ce loading of 1.0% and Ce/Fe mass ratio of 2:1, Ce-FMSY rapidly adsorbed 86.2% of F− within 30 min, with a maximum adsorption capacity of 4.139 mg·g−1. The saturated magnetization of Ce-FMSY was 13.4 emu·g−1, enabling rapid solid-liquid separation. The adsorbent maintained a stable fluoride removal rate of 77.1%–96.8% over an initial pH range of 3–9. Adsorption kinetics and isotherm fitting indicated that F− adsorption onto Ce-FMSY followed pseudo-second-order kinetics and the Freundlich model, suggesting chemisorption as the dominant mechanism, involving rapid diffusion, surface complexation, and valence transformation reactions. After five adsorption-desorption cycles, the adsorption capacity slightly decreased and then stabilized, with F− removal efficiency maintained at approximately 72.3% of the initial value. This study provides data support and theoretical reference for deep fluoride removal from wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4118-0
Polymer composite dielectrics are key materials for high-temperature film capacitors, yet their energy storage capability is severely constrained at elevated temperatures. Molecular fillers that simultaneously integrate deep-level trapping (high electron affinity, Ea), strong insulation (large bandgap, Eg), and high thermal stability are rarely available, posing a major challenge for improving high-temperature energy storage performance. To address this challenge, we screen and identify hexaazatriphenylene hexacarbonitrile (HAT-CN) as a promising candidate that fulfills the above critical requirements from numerous commercial organic molecules. When incorporated into a high glass transition temperature (Tg) polymer fluorene polyester (FPE), the resulting all-organic composite exhibits simultaneously suppressed high-temperature conduction loss and preserved mechanical robustness. Consequently, the optimized composite achieves record-high discharged energy densities of 7.31 J cm−3 at 150 °C and 6.14 J cm−3 at 200 °C (η≥90%) with a low cost and scalable process. This work demonstrates that the filler design based on synergistic key properties provides a potent pathway to break the longstanding high-temperature performance bottleneck in polymer dielectrics.