SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4217-y
Rational design and construction of effective photocatalysts is a promising way for green and sustainable chemistry, but still a great challenge. Herein, taking triphenylamine-containing aldehydes as reactants, two covalent triazine frameworks (CTFs), tris(4-formylphenyl)amine (TPA)-CTF and tris(4-formylbiphenyl)amine (TBPA)-CTF, were rationally constructed. The strong electron donor property of the triphenylamine moieties derived from the initial reactants and the strong electron acceptor nature of the in-situ formed built-in triazine rings in CTFs endowed these robust triphenylamine-based CTFs with donor-acceptor (D-A) or donor-π-acceptor (D-π-A) structure features. Photocatalytic experiments revealed that, compared with the controlled phenyl analogue CTF, 1,3,5-tri(p-formylphenyl)benzene (TFPB)-CTF, both of the triphenylamine-based CTFs exhibited superior photocatalytic activity not only in photocatalytic hydrogen peroxide generation, but also in photocatalytic aerobic oxidations of diverse organic substrates. Theoretical studies further confirmed that their enhanced photocatalytic performance should be attributed to their unique D-A or D-π-A features in the constructed triphenylamine-based CTFs. This work successfully demonstrated that rational selection of reactants containing electron donor moieties to construct CTFs should be a reliable way for the construction of effective photocatalysts for photocatalytic oxidation reactions.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.