SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4182-6
Substrate interactions dictate the epitaxial growth of low-dimensional nanomaterials, yet controlling these interfaces at the atomic scale precision remains a critical challenge. Blue phosphorene (blueP) with freestanding lattice constant, experimentally realized exclusively on Ag(111), provides a unique platform to explore this interplay. Here, we elucidate the structural evolution of blueP on Ag(111), revealing that neighboring islands are not isolated but linked by single-phosphorus-atom bridges. To manipulate the interfacial coupling, we introduce a tellurium interlayer, driving the formation of an interfacial AgTe buffer that effectively decouples the islands. By tuning the substrate temperature, we achieve the synthesis of magic-number blueP clusters with uniform size and geometry. The resulting isolated blueP nanostructures facilitate the emergence of higher-order topological corner states in triangular geometries. Our findings demonstrate that tailoring interfacial interactions offers a robust route for reshaping phosphorene nanostructures, establishing essential building blocks for next-generation topological quantum materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225221
The proliferation of lithium-ion batteries (LIBs) in portable electronics and electric vehicles has generated a pressing need for sustainable recycling of spent batteries. Conventional pyrometallurgical and hydrometallurgical routes suffer from low metal recovery efficiencies or require additional precipitants. This study introduces a clean and efficient process for recovering lithium (Li) and cobalt (Co) from spent LiCoO2 cathode materials using a choline chloride-oxalic acid-water (ChCl-OA-H2O) deep eutectic solvent (DES). The method exploits selective precipitation of Co as cobalt oxalate dihydrate (CoC2O4·2H2O) followed by water-content-regulated recovery of Li as lithium oxalate (Li2C2O4) via evaporation crystallization, eliminating the need for external precipitants. Under optimized conditions (molar ratio 1:1:8, solid-liquid ratio 100 g/L, 90 °C, 6.5 h), the leaching efficiency of Li reached 99.4%, with recovery efficiencies of 88.3% for Li and 97.8% for Co. The DES system demonstrated robust cycling stability, maintaining Li and Co recoveries of 78.1% and 92.8% after six regeneration cycles. This work provides a low-pollution, economically viable pathway for LIB recycling, contributing to resource sustainability and offering significant industrial potential.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3858-8
High-quality β-Ga2O3 membranes are pivotal for fabricating high-performance memristive devices. Here, vertical Ag/β-Ga2O3/Pt memristors built on high-crystalline-quality β-Ga2O3 membranes via lattice epitaxy engineering and a sacrificial-layer-assisted exfoliation strategy are reported. The resulting β-Ga2O3-based device demonstrates a high ON/OFF ratio exceeding 10^8, low SET/RESET voltages of 0.13 V/−0.11 V, low programming current of 10^-10 A, stable data retention beyond 4 × 10^4 s, and excellent subthreshold characteristics of ~0.47 mV/dec. Adjustable compliance current enables the coexistence of volatile and non-volatile switching modes. Additionally, the resistive switching versatility is predominantly governed by the migration of Ag ions, as supported by electrical characterizations and first-principles calculations. Furthermore, a β-Ga2O3 memristor-based circuit that functions as a reconfigurable and non-volatile exclusive OR (XOR) logic gate has been designed and simulated, enabling both image encryption/decryption and edge detection. This work not only demonstrates lattice-engineered, high-quality β-Ga2O3 membranes for fabricating advanced memristors but also extends their applicability to digital logic and reconfigurable image processing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3974-1
MAB-phase-derived compounds exhibit promising electromagnetic wave (EMW) absorption properties due to their unique layered structure and desirable physicochemical characteristics. Among them, Cr2AlB2 is particularly attractive owing to its excellent thermal and electrical conductivity. However, conventional synthesis of Cr2AlB2 requires inert gas protection to prevent oxidation, significantly increasing production costs and limiting its application in EMW absorption. To overcome this bottleneck, we report the successful synthesis of high-purity Cr2AlB2 in ambient air using the molten salt shielded synthesis (MS3) method. This approach not only isolates the material from oxygen interference but also reduces the synthesis temperature, offering a cost-effective and scalable route. The as-synthesized Cr2AlB2 exhibits outstanding EMW absorption performance: a minimum reflection loss (RLmin) of -42.10 dB at 12.6 GHz and a maximum effective absorption bandwidth (EABmax) of 3.44 GHz at a thickness of 1.9 mm. This work not only facilitates the large-scale production of Cr2AlB2 but also provides critical insights into its practical application as a high-performance EMW absorber.