SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4395-x
Electrocatalysts in lithium–sulfur (Li–S) batteries accelerate sulfur species redox reactions and restrict polysulfide shuttling, yet ideal electrocatalysts with remarkable bidirectional catalytic effects remain scarce. This work utilizes iron (Fe) to trigger bidirectional catalytic effects in a cobalt (Co) electrocatalyst, generating a metal alloy-based heterostructure of Co-Co7Fe3 dispersed homogeneously on carbon sheets (Co-Co7Fe3/CS). Electrochemical tests and in situ X-ray diffraction disclose significantly enhanced bilateral catalytic activity of Co-Co7Fe3 compared to bare Co, confirmed by self-discharge measurements. Post-cycling investigation validates protection of the Li metal anode from sulfur species corrosion. The Co-Co7Fe3/CS-modified coin cells deliver an exceptional rate capability of 603 mAh g–1 at 5.0 C and steady long-life cycling for 500 cycles at 1.0 and 2.0 C. Under high sulfur loadings and lean electrolyte conditions, an impressive areal capacity with stable cycling is realized. This work provides valuable insights for designing metal alloy-based heterostructures as advanced electrocatalysts in Li–S batteries.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604012
A newly constructed wastewater treatment plant with a design capacity of 100,000 m3/d receives influent containing approximately 15% industrial wastewater, resulting in water quality and quantity fluctuation coefficients of 1.2–1.5, refractory organic matter (as COD) exceeding 35% of total COD, and a total nitrogen (TN) concentration up to 55 mg/L. To ensure stable effluent compliance and enhance shock resistance, a modified Bardenpho process was implemented, integrating multi-point influent distribution, post-anoxic and post-aerobic zones, and supplemented with an equalization basin, high-efficiency sedimentation tank, and denitrifying deep-bed filter. During commissioning and operation, the process achieved average removal efficiencies of 96.10% for COD, 98.24% for NH3-N, 83.89% for TN, and 98.29% for TP. Effluent concentrations stabilized at 15.4 mg/L COD, 0.57 mg/L NH3-N, 7.94 mg/L TN, and 0.12 mg/L TP, consistently meeting the Class 1A standard of GB 18918—2002. The modified Bardenpho process demonstrates strong adaptability and stability for treating wastewater with high nitrogen and refractory organic loads, improving carbon source utilization and reducing energy consumption. Design parameters and operational experience provide valuable references for similar municipal plants, particularly those receiving significant industrial wastewater fractions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3781-8
The 2xxx (Al-Cu-Mg) alloy is widely used in transportation fields due to its excellent strength-to-weight ratio. However, conventional heat treatments such as peak aging (PA) often result in a pronounced strength-ductility trade-off and limited fatigue resistance. To address these limitations, this work presents a comprehensive study on the mechanical properties and fatigue behavior of Al-Cu-Mg alloy subjected to a cyclic plasticity treatment. The cyclic strengthened (CS) samples exhibit a well-balanced combination of strength and ductility due to the formation of nanoscale solute clusters. A systematic and quantitative analysis of the strengthening mechanisms is performed to evaluate the contributions of key microstructural features to the mechanical response. Moreover, the CS samples also demonstrate a significantly higher fatigue ratio and fatigue strength compared to the PA sample, despite exhibiting comparable tensile strength. These improvements are attributed to the absence of weak precipitate-free zones (PFZs) induced as a result of cyclic plasticity, which completely eliminates the pronounced strength differential between the grain interiors and the PFZs observed in the PA state. This microstructural uniformity effect effectively suppresses strain localization under cyclic loading, promotes a more homogeneous strain partitioning, and consequently delays fatigue crack initiation. These findings highlight cyclic plasticity treatment as a promising microstructure design strategy for simultaneously enhancing the mechanical and fatigue properties of high-strength Al alloys.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050601
China's iron and steel industry has undergone comprehensive ultra-low emission transformation, meeting stringent limits for conventional pollutants, yet the fate of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) remains unclear. This study combined field sampling and literature review to analyze PCDD/Fs emission characteristics from sintering, converter, and electric arc furnace processes before and after transformation, and calculated national emissions for 2022. Results demonstrate that ultra-low emission transformation effectively reduces PCDD/Fs emissions. Specifically, emission concentrations decreased by 86.5%, 95.1%, and 66.9% for sintering, converter, and electric arc furnace, respectively, with corresponding emission factors dropping to 0.11, 0.009, and 0.014 μg I-TEQ·t−1 product. Under the transformation scenario, total national emissions were 104 g I-TEQ (uncertainty ±26 g), a 94.9% reduction from the unreformed scenario (2049 ± 763 g I-TEQ). Congener profiles shifted from high-chlorinated dominance to low-chlorinated dominance, while toxicity equivalent distribution remained dominated by 2,3,4,7,8-PeCDF (35%–56%). This study quantifies the co-benefit of PCDD/Fs reduction, providing critical data for updating China's emission inventory and formulating toxicity-oriented control policies.