SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3407-0
Grain boundary (GB) engineering has emerged as a promising strategy to enhance the near-room-temperature performance of Mg3(Sb,Bi)2-based thermoelectric materials, yet effective control of Mg distribution at GBs remains a significant challenge. Here, we report a novel approach to achieve targeted Mg segregation at GBs through strategic Ag incorporation in Mg3.3Sb0.5Bi1.497Te0.003. Through comprehensive microstructural characterization and first-principles calculations, we demonstrate that Ag preferentially segregates at GBs, forming Mg-rich MgAg alloy phases while maintaining limited solid solubility within the matrix. This unique GB architecture simultaneously optimizes multiple thermoelectric parameters: the Mg-rich GB regions significantly provide efficient carrier transport channels and enhance carrier mobility, while the MgAg phases and lattice disorders effectively scatter phonons without disrupting electron transport. Consequently, the optimized composition (x = 0.01) exhibits a remarkable enhancement in power factor at 300 K and maintains an average ZT of ~1.0 across 300–400 K. The material also demonstrates excellent mechanical properties and thermal stability, making it particularly suitable for near-room-temperature applications. Our findings not only establish an effective strategy for GB engineering in Mg3(Sb,Bi)2 systems but also provide valuable insights into the rational design of high-performance thermoelectric materials through interface modification.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61093-1
Advanced catalyst structures with good active site accessibility and strong metal-support interactions are crucial for oxygen reduction reaction (ORR) catalysis. A hierarchically porous Pt catalyst supported on honeycomb-like nitrogen-doped carbon (Pt/HNC-400, where 400 denotes the optimal dosage (mg) of the sacrificial SiO2 hard template used during synthesis) was fabricated by combining template-assisted pyrolysis and alcohol reduction. The fabrication involves the template-assisted pyrolysis of ZIF-67 (which provides the N-dopant through its 2-methylimidazole ligand) followed by HF etching to completely remove the SiO2, yielding a 3D interconnected porous carbon support. Compared to a commercial Pt/C, it had an exceptional ORR performance with a half-wave potential of 0.901 V (41 mV higher), a mass activity at 0.9 V that was 15.3 times higher, and significantly improved durability (a half-wave potential decay of 25 mV vs. 80 mV after 10,000 accelerated durability tests (ADTs)). Mechanistic investigations showed that this superior performance is due to the combined effects of the 3D porous structure, ultrafine Pt nanoparticles with strong metal-support interactions, and in-situ formed Co-Nx moieties from the pyrolysis of precursor ZIF-67. After 10,000 ADTs it was shown to have excellent structural integrity, retaining 87.4% of its initial electrochemically active surface area (102.7 m2 g−1). This study may assist the development of new high-performance ORR catalysts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605001
The lower reaches of the Yangtze River Basin, as a concentrated area of China's C5 petroleum resin industry, face critical bottlenecks in green and low-carbon transformation due to high-pollution, refractory wastewater and high carbon emissions. Traditional petrochemical wastewater treatment technologies suffer from low efficiency, high energy consumption, and insufficient resource utilization. This paper systematically analyzes the sources of wastewater in C5 petroleum resin production from principles and processes, and reviews research progress and carbon reduction potential of current technologies in three aspects: new materials, new equipment, and new processes. Integrated processes centered on efficient pretreatment, biological enhancement, and multi-technology coupling show significant advantages in improving treatment efficiency, reducing energy consumption and cost, and strengthening resource recovery. The study also prospects future research priorities for pollution and carbon mitigation through green technological innovation and intelligent upgrading, providing new solutions for 'near-zero discharge' and resource recycling of C5 petroleum resin wastewater, thereby promoting the green and low-carbon transformation of the petrochemical industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3750-6
SnSe is a promising thermoelectric material for medium-temperature applications due to its ultralow lattice thermal conductivity. However, the poor electrical conductivity of n-type polycrystalline SnSe significantly hinders its practical application. Here, we propose a dual-functional strategy employing InBr3 doping to synergistically enhance electrical transport while suppressing lattice thermal conductivity. For the first time, we demonstrate the successful construction of a Br-enriched conductive network within the SnSe matrix. The incorporation of In3+ and Br− introduces high-density charge carriers, while Br forms percolative conductive networks, resulting in a remarkable enhancement of carrier mobility to ~20.64 cm2 V−1 s−1. Simultaneously, the lattice thermal conductivity is substantially reduced to ~0.25 W m−1 K−1 through the formation of multi-scale defects, including dislocations and Br-rich nanowires, which effectively enhance phonon scattering. As a result, we achieve a peak figure of merit of ZT ~1.41 at 823 K, with an average figure of merit of ~0.42 over the temperature range of 323–823 K. This work provides a universal paradigm for decoupling electron-phonon interactions in thermoelectric materials, offering new insights for the optimization of thermoelectric performance.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3472-2
Reducing zinc oxide (ZnO) consumption in rubber vulcanization is imperative due to cost and environmental toxicity, yet lowering ZnO inevitably compromises crosslinking density and mechanical properties. This study introduces Zn single-atoms anchored on graphene oxide (Zn SAs@GO) as controlled-release catalysts for efficient natural rubber (NR) vulcanization. X-ray absorption spectroscopy (XAS) reveals a Zn–O bond length of 2.03 Å with moderate binding energy, enabling controlled release of Zn2+ ions that participate in vulcanization with enhanced activity. The homogeneous dispersion of Zn atoms ensures near-complete utilization, resulting in a 6.6% increase in crosslinking density compared to commercial ZnO while reducing Zn dosage by 82.5%. The Zn SAs@GO/NR composites exhibit faster vulcanization rates and superior mechanical and physical properties relative to ZnO nanoparticles and crystalline ZnO controls. This work demonstrates a scalable preparation of single-atom catalysts and provides a viable pathway for industrial rubber manufacturing with significantly reduced zinc content.