SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4290-9
Thermoelectric materials enable direct and reversible conversion between heat and electricity, offering unique advantages for waste heat recovery, solid-state refrigeration, and deep-space power systems. The performance is evaluated by the dimensionless figure of merit, zT = S²σT/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature, and κ is the total thermal conductivity. Achieving high zT requires simultaneous realization of a large power factor (S²σ) and low thermal conductivity. However, these parameters are intrinsically coupled, posing a fundamental challenge. PbTe is a representative thermoelectric material operating in the intermediate temperature range, with outstanding performance originating from its unique electronic band structure featuring multiple nearly degenerate valence band maxima near the L points. Band convergence via alloying with mono-tellurides such as MgTe, MnTe, CdTe, YbTe, SrTe, and EuTe effectively modifies the valence band structure, increasing band degeneracy and density-of-states effective mass, thereby enhancing electrical conductivity without decreasing the Seebeck coefficient. However, increasing the content of these mono-tellurides limits acceptor dopability, making conventional dopants like Na difficult to incorporate. This study demonstrates that co-doping strategies can preserve dopability while achieving band convergence and dislocation engineering, leading to significantly reduced lattice thermal conductivity and extraordinary peak zT values. The decoupling of electronic and thermal transport through this approach offers a promising route for high-performance thermoelectrics.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0027
Electrocatalytic CO2 reduction reaction (CO2RR) offers a promising route to mitigate CO2 emissions while producing valuable chemicals. This study reports a Cu-Sn alloy catalyst with a wheat-ear-like dendritic structure, fabricated via a one-step electrodeposition method, for selective CO2 electroreduction to formate. Compared to pure Cu and Sn electrodes, the Cu-Sn alloy exhibits superior catalytic activity and selectivity toward formate, achieving a maximum Faradaic efficiency (FE) of 80% and maintaining above 70% FE over a potential window from -1.7 V to -2.0 V (vs. Ag/AgCl). The enhanced performance is attributed to the unique dendritic morphology that provides abundant active sites and the synergistic alloying effect that modulates the adsorption of the CO2*- intermediate, as corroborated by electrochemical measurements and X-ray photoelectron spectroscopy (XPS). This work presents a facile strategy for designing bimetallic catalysts for efficient CO2RR to formate.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092802
Activated carbon (AC) filters in drinking water treatment plants (DWTPs) experience significant adsorption performance decline over extended operation, yet complete media replacement is a major cost. To evaluate cost-effective strategies, pilot-scale column experiments with five AC replacement ratios (0%, 30%, 50%, 70%, and 100%) were conducted to assess removal of disinfection by-product (DBP) precursors and pesticide-related emerging contaminants. For dissolved organic matter (DOM), all fractions except low molecular weight compounds (LMWC) achieved >85% of the removal obtained with full replacement when 70% new AC was used, with UV254 removal reaching 70%. LMWC, due to small molecular size and low adsorption energy, required higher replacement ratios or full replacement for substantial removal. For DBPs, removal of trihalomethanes (THMs) and haloacetic acids (HAAs) was insensitive to replacement ratio, while haloacetaldehydes (HALs) removal improved markedly with increasing ratio, indicating structural selectivity. For pesticide-related contaminants, all except triazoles achieved >95% removal at 70% replacement; triazoles, due to high water solubility, high polarity, and low octanol-water partition coefficient, achieved only ~60% removal. Overall, replacing 70% of AC restored treatment performance to >80% of that with full replacement, ensuring effluent quality while saving ~30% of new carbon cost. Molecular structure, polarity, and pore size matching are key determinants of removal efficiency; optimizing replacement ratio balances water quality and economic benefits.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60626-8
The dense crystalline structure and limited accessibility of cellulose severely hinder its efficient catalytic conversion. In response, biomimetic solid acid catalysts inspired by cellulase binding domains (CBDs) have emerged as a promising strategy to enhance cellulose hydrolysis by mimicking the substrate recognition and enrichment functions of natural enzymes. This review systematically summarizes recent advances in the design of CBD-mimetic solid acids based on four representative strategies: electrostatic anchoring, hydrophobic microenvironment engineering, spatial confinement, and covalent lock-and-key mechanisms. The underlying principles of these approaches, including substrate-specific recognition, local concentration enhancement, and synergistic “adsorption-catalysis” effects, are critically discussed to elucidate their contributions in improving catalytic affinity, selectivity, and durability. Despite significant progress, challenges such as mass-transfer resistance and insufficient structural robustness remain in complex biomass conversion systems. Looking forward, the integration of sub-enzymatic materials, such as carbon quantum dots (CQDs), into biomimetic catalysts offers new opportunities to achieve efficient, recyclable, and hierarchically organized catalytic systems, thereby providing a powerful route for the sustainable valorization of cellulose and other lignocellulosic resources.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607009
Resource utilization of food waste is a key measure for implementing waste classification and constructing zero-waste cities in China. However, the technical route based on anaerobic digestion currently faces developmental bottlenecks. In this study, engineering-scale facilities located in Northeast, North, Northwest, and Southeast China were selected, and material flow analysis was employed to comprehensively assess the current status of anaerobic digestion of food waste. The results indicated that, during the pretreatment stage, both leachate and organic slurry from all surveyed regions exhibited high COD/TN ratios, and the leachate contained high concentrations of lipids. Following three-phase (oil-water-solid) separation, the oil recovery rate could reach over 98%. Anaerobic digestion of each ton of food waste from the four regions generated approximately 70 to 80 Nm³ of biogas, while simultaneously producing liquid digestate accounting for 69% to 80% of the total mass and solid digestate accounting for 2.7% to 3.6%. However, the annual continuous production of digestate was not aligned with the seasonal demand for land use, thereby restricting the pathway for resource utilization. Converting food waste into an external carbon source can significantly enhance its resource utilization efficiency, with the economic benefits increasing by more than 203% compared to the methanogenesis pathway. The selection of the carbon source production technology route should be comprehensively determined by taking into account factors such as the specific nitrogen removal requirements of the target wastewater treatment process, the quality requirements for the carbon source products, and the substitution rate of commercial carbon sources.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607010
The impact of low concentrations of perfluorooctane sulfonate (PFOS) on anaerobic fermentation of waste activated sludge (WAS) remains poorly understood. This study applied three PFOS levels (0.5, 1.0, and 4.5 μg/g TSS) to systematically evaluate effects on organic matter solubilization and nitrogen/phosphorus transformations. Monitoring of soluble chemical oxygen demand (SCOD), soluble protein, polysaccharides, NH4+-N, PO43--P, and three-dimensional excitation-emission matrix (3D-EEM) fluorescence revealed that PFOS significantly enhanced release of SCOD, protein, and polysaccharides. At 45 °C after 14 days with 4.5 μg/g TSS, SCOD peaked approximately 28% higher than control, indicating increased biodegradable organic matter accumulation. NH4+-N concentrations rose overall with fluctuations, while PO43--P release was inhibited, suggesting interference with nutrient transformation pathways. 3D-EEM analysis showed strengthened signals of aromatic proteins and microbial by-products, confirming matrix solubilization. These findings demonstrate a dual effect of low-level PFOS: initial promotion of organic matter release followed by potential inhibition of nutrient transformation. This study provides data support for understanding PFOS environmental behavior in anaerobic digestion and informs sludge resource utilization and risk assessment of emerging contaminants.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026021203
Neonicotinoid insecticides (NEOs) are widely used pesticides with residues entering the human body via multiple routes, posing potential health risks. Pregnant women are a sensitive population requiring investigation into NEO exposure effects. Based on the Jiashan Birth Cohort, this study measured 12 NEOs (9 parent compounds and 3 metabolites) and three oxidative stress biomarkers (8-iso-prostaglandin F2α, 8-iso-15(R)-prostaglandin F2α, and 8-hydroxy-deoxyguanosine) in urine from 917 pregnant women using liquid chromatography-triple quadrupole mass spectrometry. Demographic data were integrated to analyze exposure patterns and associations. Results showed at least one NEO detected in all samples; seven NEOs had detection rates >50%. Median creatinine-adjusted total concentration was 5.613 μg·g−1. Acetamiprid-N-desmethyl (N-dm-ACE) had the highest detection rate (98.59%) and largest concentration proportion (64.2%). Spearman correlation, multiple linear regression, and Bayesian kernel machine regression revealed positive associations between oxidative stress markers and NEO exposure. Specifically, 8-PGF and 15-PGF correlated positively with thiacloprid-amide (THI-amid) and dinotefuran (DIN); 8-OHdG correlated positively with thiamethoxam (THM) and sulfoxaflor (SFX). Health risk assessment indicated hazard quotients below 1 for all NEOs, suggesting low health risks. This study provides evidence linking NEO exposure to oxidative stress damage in pregnant women, informing risk assessment for sensitive populations.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041505
To combat severe air pollution, China has implemented a series of air pollution control action plans since 2013, effectively alleviating PM2.5 pollution. However, PM2.5 concentrations in most cities within the Fenwei Plain still exceed national standards. This study systematically evaluates PM2.5 concentration changes across two policy phases (2013–2020) using the Community Multiscale Air Quality (CMAQ) model, quantifying contributions of meteorology and emissions, and analyzing sectoral source changes. Results show that annual average PM2.5 concentration declined cumulatively by 19% during 2013–2020. In the first phase (2013–2017), regional PM2.5 decreased by 3% annually, with most improvement in winter; however, due to unfavorable meteorology, concentrations increased in Xi'an and Xianyang. In the second phase (2017–2020), PM2.5 declined by an additional 16%, with more effective control measures, particularly in spring and autumn. Emission reductions dominated in both phases, with stronger effects in the second phase (−8 μg·m−3), significantly outweighing adverse meteorological contributions (+3.5 μg·m−3). Nevertheless, many cities still face challenges from unfavorable meteorology, highlighting the need for future policies to account for meteorological influences. Emissions from industrial, energy, and agricultural sources decreased significantly across both phases. However, during winter heating periods, residential emissions emerged as a source equal in importance to industrial emissions, becoming a key target for future emission controls.