SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3722-3
Magnesium alloys are promising biodegradable bone implant materials due to their biocompatibility and mechanical compatibility, but rapid degradation and postoperative bacterial infection limit clinical application. Here, zeolitic imidazolate framework-8 (ZIF-8) and 3,4,9,10-perylenetetracarboxylic diimide (PD) composite coatings (ZIF-8@PD) were fabricated in situ on micro-arc oxidation (MAO) coated AZ31 alloys via two-step and one-step (OS) methods. The MAO/ZIF-8@PD and MAO/ZIF-8@PD (OS) coatings reduced corrosion current density by three and two orders of magnitude, respectively, compared to MAO coating, due to the physical barrier of the 2D-co-3D MOF structure. Under 808 nm near-infrared laser irradiation, photothermal and photodynamic effects from PD, combined with contact killing by released Zn2+ ions, achieved bactericidal rates ≥99.5% against E. coli and S. aureus. Photothermal conversion efficiencies were 44.01% and 48.57% for the two-step and one-step coatings, respectively. The distinct Zn2+ sources led to different 2D-co-3D MOF structures, influencing degradation and antibacterial behavior. These coatings offer a strategy to enhance corrosion resistance and antibacterial activity of Mg alloys for biomedical applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031102
Laccases are promising biocatalysts for environmental remediation, yet their application is hindered by the instability and limited substrate affinity of wild-type enzymes. Here, we report a computational strategy integrating homology modeling, molecular docking, and virtual mutagenesis to engineer high-performance laccase mutants targeting benzene-containing pollutants. Structural analysis revealed that fungal laccase (Trametes versicolor, T.v) exhibited stronger binding affinities for aniline, o-phenylenediamine, and 1-hydroxybenzotriazole (HBT) compared to bacterial laccase (Bacillus subtilis, B.s), attributed to optimized hydrophobic and hydrogen-bond interactions within the substrate-binding pocket. Virtual mutagenesis identified critical residues (e.g., Ser113, Leu459) regulating substrate stability. Notably, mutations at Ser113 to Arg/Glu/Leu significantly enhanced binding energy (ΔG ≤ −7.1 kcal·mol−1 for HBT) by narrowing the pocket exit and reinforcing hydrophobic constraints. Mechanistically, polar mutations in the pocket interior promoted hydrogen bonding, while hydrophobic substitutions at peripheral residues restricted substrate dissociation. Our findings establish a dual-region engineering principle—enhancing hydrogen bonds internally and hydrophobicity externally—to optimize laccase activity. This work provides a generalizable framework for the rational design of oxidoreductases in pollutant degradation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511046
To evaluate the carbon footprint differences between the emerging ex-situ remediation facility mode and the conventional on-site remediation mode in China, this study employed the SEFA tool to calculate greenhouse gas (GHG) emissions and energy consumption for four typical remediation scenarios. Results indicate that the carbon emission intensity of solidification/stabilization (S/S) in the remediation facility is 12.00% higher than that of on-site S/S, with unit carbon intensities of 66.74 and 59.59 kgCO2e·m−3, respectively, and total energy consumption 11.90% higher. The soil transport segment in the facility S/S contributes 13% of carbon emissions, being the primary reason for its higher total carbon footprint. Conversely, thermal desorption (TD) in the facility exhibits 11.10% lower carbon emissions than on-site TD, with unit intensities of 269.16 and 302.78 kgCO2e·m−3, and total energy consumption 3.97% lower, mainly due to the utilization of landfill biogas as renewable energy for heat and power generation, while soil transport contributes only 3% of emissions. The reagent segment in S/S and the heat supply segment in TD account for 77%–86% and 70%–72% of total GHG emissions, respectively. The study demonstrates that remediation facilities, leveraging advantages such as landfill biogas, can actively aggregate contaminated soil from surrounding areas for centralized thermal desorption, which is beneficial for regional carbon emission reduction in soil remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4081-y
The evolution of precision medicine has propelled multimodal imaging-guided phototheranostics to the forefront for precise tumor diagnosis and therapy. Low-temperature photothermal therapy (PTT) offers a promising approach for the treatment of melanoma due to its non-invasiveness and minimal damage to normal tissues. However, its efficacy is limited by cancer cell thermal tolerance. To address this, a new type of multifunctional energy disruptor (CAMeO-Q NPs) is developed featuring homologous targeting and mitochondria targeting, and synergistically enhancing low-temperature PTT in melanoma by reversing heat shock protein 90 (Hsp90)-mediated thermal tolerance and blocking mitochondrial adenosine triphosphate (ATP) biosynthesis. The multifunctional energy disruptor enables precise trimodal imaging (fluorescence imaging/FLI, photoacoustic imaging/PAI, and photothermal imaging/PTI) guidance for low-temperature PTT. Comprising a mitochondria-targeting photothermal agent and an Hsp90 inhibitor, CAMeO-Q NPs induce selective mitochondrial damage under 660 nm laser irradiation and downregulate cellular HSP expression by ATP inhibition and Hsp90 inhibitor. This multifunctional energy disruptor provides a novel strategy for enhancing multimodal imaging-guided low-temperature photothermal therapy through combined homologous targeting, mitochondria-targeting, and Hsp90 inhibition.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60717-7
Alkali lignin, a high-volume byproduct from pulp and paper manufacturing and biomass refining, is a promising feedstock for aromatic hydrocarbon production in liquid fuels due to its high energy density and abundant aromatic moieties. However, its highly cross-linked polymeric structure hinders efficient valorization. This work investigates catalytic conversion of alkali lignin into bio-oil under in situ H2 supply from formic acid. A series of Ni-Mo/h-BN bimetallic catalysts with varied metal ratios were synthesized by impregnation and characterized by XPS, XRD, and other techniques. The effects of reaction parameters on H2 production via aqueous-phase reforming (APR) of formic acid were evaluated. Optimal H2 yield was achieved at a formic acid-to-water molar ratio of 1:10 and a Ni/Mo atomic ratio of 3:1. H2 yield increased monotonically with temperature from 220 to 280 °C, reaching a maximum of 38.48 mmol. Subsequently, influences of reaction temperature and residence time on bio-oil production were examined. The highest heavy bio-oil yield (18.93%) and maximum relative content of aromatic hydrocarbons (13.81%) were both achieved at 280 °C. Prolonged reaction time reduced heavy bio-oil yield and aromatic hydrocarbon abundance while favoring furan derivatives. This work demonstrates good synergy between in situ hydrogen generation from formic acid and lignin hydrogenation in the temperature range 240–280 °C.