SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4290-9
Thermoelectric materials enable direct and reversible conversion between heat and electricity, offering unique advantages for waste heat recovery, solid-state refrigeration, and deep-space power systems. The performance is evaluated by the dimensionless figure of merit, zT = S²σT/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature, and κ is the total thermal conductivity. Achieving high zT requires simultaneous realization of a large power factor (S²σ) and low thermal conductivity. However, these parameters are intrinsically coupled, posing a fundamental challenge. PbTe is a representative thermoelectric material operating in the intermediate temperature range, with outstanding performance originating from its unique electronic band structure featuring multiple nearly degenerate valence band maxima near the L points. Band convergence via alloying with mono-tellurides such as MgTe, MnTe, CdTe, YbTe, SrTe, and EuTe effectively modifies the valence band structure, increasing band degeneracy and density-of-states effective mass, thereby enhancing electrical conductivity without decreasing the Seebeck coefficient. However, increasing the content of these mono-tellurides limits acceptor dopability, making conventional dopants like Na difficult to incorporate. This study demonstrates that co-doping strategies can preserve dopability while achieving band convergence and dislocation engineering, leading to significantly reduced lattice thermal conductivity and extraordinary peak zT values. The decoupling of electronic and thermal transport through this approach offers a promising route for high-performance thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4350-4
Flexible wearable sensors have transformed motion tracking, soft robotics, and human-machine interfaces by enabling precise movement detection and adaptability to curved surfaces. However, conventional composite sensors often face challenges such as limited sensitivity, detection range, linearity, and durability. In this study, we propose a stretchable auxetic sensing textile with a negative Poisson’s ratio (NPR) structure, incorporating reduced graphene oxide (rGO) and carbon nanotubes (CNT) by micro-crack engineering to enhance its mechanical durability and sensing performance. Integrating macro-scale NPR with micro-scale wrinkles, this innovative design achieves a high sensitivity of 11.2 within a wide detection range (0-100%), a more linear sensing range with an R2 value of 0.998, an ultra-low detection limit of 0.5%, and exceptional durability, outperforming conventional wearable sensors. Additionally, the textile sensor boasts excellent moisture permeability (32.7 g m⁻² h⁻¹) and a remarkable NPR value of -0.25, ensuring comfort and adaptability for various wearable applications. Integrated with deep learning algorithms, the auxetic sensing textile demonstrates 98% accuracy in recognizing soft robotic movements at various bending angles. It is capable of capturing both small-scale physiological signals, such as electrocardiograms, and large-scale movements, offering significant freedom of movement and adaptability to complex surfaces.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3700-7
Photocatalytic synthesis has been considered a promising technology for solar-to-chemicals conversion. Here, a series of novel photocatalysts was synthesized by decorating uranyl sites on imine-based covalent organic frameworks (i-COF) and proved functioning for the uniformly boosted H2O2 production by 1.6–10.1 folds compared with the bare i-COFs in a wide pH range from 2 to 11. Typically, an optimal H2O2 production rate of 1435.9 μmol g−1 h−1, i.e., 28.72 mmol g(U)−1 h−1, was realized over uranyl decorated TTa-COFs under visible light. Systematic investigations reveal that the universally and remarkably promoted performance is attributed to the outstanding electron-transfer ability, accelerated activation of molecular oxygen and favored formation of ·O2− and *OOH as the key intermediate by virtue of the decorated uranyl ions; thus the two-step single-electron oxygen reduction reaction (ORR) for H2O2 photo-generation is significantly facilitated. This work paves a new way for the uranyl-decorated COFs as a novel photocatalyst and provides in-depth insight to the reaction mechanism for photocatalytic H2O2 production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3559-5
Polyamide (PA) membranes are promising for lithium extraction from spent lithium-ion battery (LIB) leachate but face a trade-off between selectivity and permeability. Here, we demonstrate that nascent PA membranes post-grafted with triaminoguanidinium (TAG) monomers (PA-TAG membranes) gain expanded ion passage channels (0.8–7.1 Å) and enhanced positive charge, achieving high-performance lithium separation. The PA-TAG membrane exhibits a pure water permeance (PWP) of 15.5 L m−2 h−1 bar−1, superior divalent ion rejection (~98%), and an excellent separation factor (~30), significantly outperforming pristine PA membranes. In a simulated acidic battery leachate, the PA-TAG membrane achieved a relative volumetric lithium recovery rate of 48.2% after a two-stage nanofiltration process, with the Li+/M2+ mass ratio of the second permeate reaching 53.35, 445 times that of the feed (0.12). The membrane maintained stable performance over 45 hours of nanofiltration and resisted acidic conditions (pH=2) for at least 20 days. These results highlight the potential of PA-TAG membranes for efficient lithium extraction from acidic battery leachate, addressing the critical need for sustainable recycling of spent LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3744-9
The high-value utilization of industrial wastes is critically important for environmental protection and sustainable development. In this work, amorphous NaFeP2O7 (NFPO) and NaFeP2O7/rGO (NFPO/rGO) composite are synthesized via a selective chemical precipitation approach, utilizing industrial jarosite residue as the iron source. The sodium storage performance and mechanism of this amorphous NFPO/rGO composite as a novel cathode material for sodium-ion batteries (SIBs) are explored for the first time. The as-synthesized amorphous NFPO/rGO composite exhibits outstanding long-term cycling performance of 79.1 mAh g−1 after 1000 cycles at 0.1 A g−1, while the crystalline NFPO/rGO composite does not work. Galvanostatic intermittent titration technique and in-situ electrochemical impedance spectroscopy analysis demonstrate that the amorphous NFPO/rGO composite has high Na+ diffusivity and fast kinetics. In-situ X-ray diffraction analysis reveals the structure change from amorphous NaFeP2O7 to triclinic Na2FeP2O7 during the first discharge process and then evolves to a highly disordered structure in the subsequent charge/discharge cycles. The present work not only provides an avenue for the high-value utilization of jarosite residue but also offers theoretical guidance for the structural design and development of NaFeP2O7-based cathode materials for SIBs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3464-4
Photocatalytic conversion of atmospheric CO2 (0.03%) into multi-carbon fuels remains a grand challenge due to the high energy barrier of C–C coupling and the low concentration of CO2. Here, we report the construction of multiple metal pair sites on metal oxide nanosheets to steer C–C coupling, enabling efficient photoreduction of air-concentration CO2 to ethane (C2H6). As a prototype, Au nanoparticles were anchored on Bi4Ti3O12 nanosheets (Au-Bi4Ti3O12). High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the formation of Au-Ti metal pair sites at the interface. In situ Fourier transform infrared spectroscopy revealed the presence of *OCCOH intermediate on Au-Bi4Ti3O12 during CO2 photoreduction, which was absent on pristine Bi4Ti3O12. Density functional theory calculations showed that the Gibbs free energy for *CO–COH formation on Au-Bi4Ti3O12 is 2.23 eV, significantly lower than that on Bi4Ti3O12 (3.59 eV), indicating facilitated C–C coupling. Consequently, Au-Bi4Ti3O12 exhibited a C2H6 evolution rate of 2.58 μmol g−1 h−1 under 0.03% CO2, whereas Bi4Ti3O12 produced only C1 products (CO and CH4). This work demonstrates the first single-catalyst photoreduction of atmospheric CO2 to C2H6, highlighting the effectiveness of engineered multiple active sites in overcoming the C–C coupling bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3737-9
The radar stealth performance of weaponry is crucial to their battlefield survivability, jointly determined by the effective absorption bandwidth (EAB) and mechanical properties of microwave-absorbing materials (MAMs). However, conventional MAMs often suffer from narrow EAB and absorption coatings prone to detachment. Herein, inspired by the wing scales of butterfly, we develop a biomimetic concave basalt fiber-reinforced composite (BC-BFRC) that delivers both broadband absorption and superior mechanical performance. Remarkably, the BC-BFRC achieves an EAB (reflection loss < −10 dB) of 14.7 GHz (3.3–18 GHz), which is 26.7% higher than the conventional planar structure (planar BFRC) and covers 91.9% of the S–Ku band. It maintains stable broadband absorption across incidence angles of 0°–45° (reflection loss < −8 dB at 4–18 GHz) and is insensitive to the incident direction. In fact, the broadband absorption originates primarily from impedance gradient between the layers and energy capture induced by the biomimetic concave at bottom. Critically, the composite exhibits a flexural strength of 239.2 MPa, enabled by basalt fiber reinforcement. This work provides a novel biomimetic strategy and feasible pathway for realizing structure-function integration of MAMs, enabling advanced radar stealth and electromagnetic shielding applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225264
The high cost of high-purity hydrogen necessitates the utilization of low-cost industrial by-product hydrogen as an alternative gas source to reduce hydrogen storage costs. Industrial by-product hydrogen typically contains impurities such as H2S and CO, yet the poisoning mechanisms of these gases on superlattice hydrogen storage alloys during hydrogen absorption/desorption remain poorly understood. This study systematically investigates the poisoning effects and regeneration behavior of La0.65Mg1.32Ca1.03Ni9Y0.17 superlattice hydrogen storage alloy in atmospheres containing 10^-3 H2S and CO. The experimental protocol comprised 10 poisoning cycles followed by 1 regeneration, repeated to total 20 poisoning cycles and 2 pure hydrogen regenerations. Results show that in pure hydrogen, the alloy's hydrogen storage capacity gradually decreases after 22 cycles but is effectively restored after dehydrogenation at 473 K. In the presence of impurity gases, the hydrogen storage capacity retention rates after 10 poisoning cycles with H2S and CO are 3.56% and 2.71%, respectively; after 20 cycles, these decrease to 3.68% and 1.73%, respectively. After dehydrogenation at 473 K, retention rates recover to 40.35% and 98.27%, respectively. This indicates that poisoning severity follows the order CO > H2S, while regeneration difficulty follows H2S > CO. X-ray diffraction analysis reveals that after poisoning, the main phase transforms from AB3 to AB3H, but reverts to AB3 after high-temperature dehydrogenation. X-ray photoelectron spectroscopy shows that after H2S poisoning, CaS and CaSO4 form on the alloy surface, indicating irreversible chemical adsorption. In contrast, after CO poisoning, no new substances are detected, indicating reversible adsorption. This study clarifies the differentiated poisoning mechanisms of impurity gases and provides theoretical support for the application of rare-earth superlattice hydrogen storage alloys in complex atmospheres.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3806-0
Sonodynamic therapy (SDT) faces critical limitations from inefficient sonosensitizers and the hypoxic tumor microenvironment, which curtail reactive oxygen species (ROS) generation. Here, we report a dual enzyme-mimicking sonosensitizer, termed sonozyme, engineered by integrating platinum nanoparticles (Pt NPs) with a tailored covalent organic framework (Y-COF). The spatially separated donor-acceptor architecture optimizes the band position of Y-COF, conferring intrinsic sonodynamic activity. Pt NPs further enhance ultrasound-triggered ROS generation by promoting exciton separation and transfer. Notably, sonozyme exhibits catalase (CAT) and peroxidase (POD) mimetic activities, converting endogenous H2O2 into O2 and ·OH, thereby alleviating hypoxia and augmenting oxidative stress. In vitro assays demonstrated significantly enhanced ROS production and cancer cell death under ultrasound irradiation. In vivo studies confirmed that sonozyme effectively suppresses tumor progression without observable systemic toxicity. This work presents a paradigm for designing high-performance multifunctional sonosensitizers, offering a promising strategy for cancer therapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509080
Plastic pollution poses a global environmental challenge, and developing efficient, low-cost pyrolysis catalysts is crucial for resource recovery from plastic waste. This study investigates ex-situ catalytic pyrolysis of low-density polyethylene (LDPE) over ZSM-5 (Si/Al = 25) modified with Zn and Fe at loadings of 5% and 10% via impregnation. Catalysts were characterized by XRD, FT-IR, XPS, SEM, TEM, and BET. TGA was used to assess thermal behavior, and catalytic pyrolysis experiments were conducted in a tube furnace at 450 °C, with product analysis by GC-MS. Results show that metal incorporation preserved the ZSM-5 framework while modifying acid site distribution and surface morphology, enhancing cracking and dehydrogenation. All modified catalysts increased light gasoline-range hydrocarbon yield and reduced heavy fractions compared to non-catalytic runs. Among them, 10% Zn/ZSM-5 exhibited the best performance, boosting light gasoline hydrocarbons to 74.77%, approximately three times that of the non-catalytic case, significantly improving oil quality. This study demonstrates the potential of low-cost metal-modified zeolites for efficient and economical plastic waste pyrolysis.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021005
Microplastic pollution in freshwater environments has escalated, leading to increased accumulation in wild fish. This study investigated the occurrence characteristics of microplastics (MPs) in the gills, gastrointestinal tract (GIT), and muscle of four wild fish species with different feeding habits from Baiyangdian Lake, China. MPs were detected in all tissues. The average abundance was highest in the GIT (11.63 ± 10.76 items/individual), followed by gills (7.44 ± 6.79 items/individual), and lowest in muscle (3.91 ± 3.16 items/individual). The majority of MPs were transparent and black fibers smaller than 0.5 mm. Polymer analysis identified polypropylene (PP) and polyethylene (PE) as dominant components. Significant differences in MP abundance were observed among species, with carnivorous and herbivorous fish (e.g., snakehead and grass carp) showing higher total MPs than omnivorous and planktivorous fish (e.g., mosquitofish and topmouth gudgeon). However, when normalized by body weight, smaller fish exhibited higher MP concentrations in the GIT, suggesting a greater risk per unit mass. This study provides baseline data on tissue-specific MP distribution in wild freshwater fish with varying feeding behaviors and habitats, highlighting the influence of trophic level and body size on MP accumulation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60626-8
The dense crystalline structure and limited accessibility of cellulose severely hinder its efficient catalytic conversion. In response, biomimetic solid acid catalysts inspired by cellulase binding domains (CBDs) have emerged as a promising strategy to enhance cellulose hydrolysis by mimicking the substrate recognition and enrichment functions of natural enzymes. This review systematically summarizes recent advances in the design of CBD-mimetic solid acids based on four representative strategies: electrostatic anchoring, hydrophobic microenvironment engineering, spatial confinement, and covalent lock-and-key mechanisms. The underlying principles of these approaches, including substrate-specific recognition, local concentration enhancement, and synergistic “adsorption-catalysis” effects, are critically discussed to elucidate their contributions in improving catalytic affinity, selectivity, and durability. Despite significant progress, challenges such as mass-transfer resistance and insufficient structural robustness remain in complex biomass conversion systems. Looking forward, the integration of sub-enzymatic materials, such as carbon quantum dots (CQDs), into biomimetic catalysts offers new opportunities to achieve efficient, recyclable, and hierarchically organized catalytic systems, thereby providing a powerful route for the sustainable valorization of cellulose and other lignocellulosic resources.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3864-4
Organic room temperature phosphorescence (RTP) materials, particularly those emitting in the near-infrared (NIR) region, hold great promise for bioimaging due to their deep-tissue penetration and minimal autofluorescence interference. However, achieving efficient NIR RTP with long lifetimes remains challenging due to inefficient triplet exciton utilization. Herein, we propose a dark triplet state activation strategy to achieve efficient NIR RTP by leveraging host–guest energy transfer. Using benzophenone derivatives (BP, OBP, MBP, PBP) as rigid host matrices with high intersystem crossing (ISC) efficiency and an NIR fluorophore (MPTCF) as the guest, we achieve efficient Dexter-type triplet-triplet energy transfer (TTET) that converts non-emissive host triplets into guest-centered NIR phosphorescence. Systematic optimization of the host–guest system has shown that PBP/MPTCF exhibits exceptional performance, including long phosphorescence centered at 705 nm, an ultralong phosphorescence lifetime (210.3 ms), and high ISC efficiency (44.4%). When fabricated into nanoparticles (NPs), PBP/MPTCF exhibits superior performance, featuring prolonged phosphorescence signals (>120 s), deep tissue penetration capability (>2 mm), and excellent biocompatibility (cell viability >95% at 300 μM). In addition, this system enables high-contrast subcutaneous imaging with excellent dispersibility and stable in vivo imaging capability. More importantly, PBP/MPTCF NPs demonstrate precise lymph node mapping through time-gated phosphorescence imaging and efficient tumor visualization within 4 h post-injection with a high tumor-to-liver ratio of 2.8. The successful activation of dark triplet states through this host–guest approach provides a general design principle for developing high-performance NIR RTP materials, while the demonstrated biomedical applications highlight their significant potential for advanced bioimaging and precision diagnostics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040705
Chromium is a common environmental metal pollutant. Shewanella oneidensis MR-1 can generate extracellular electrons, facilitating the reduction of Cr(VI) to Cr(III), thereby mitigating its toxicity. Both biochar and electroactive dissolved organic matter (e-DOM) regulate extracellular electron transfer during Cr(VI) bioreduction. In practice, surface DOM on biochar can detach and enter the environment, while the biochar matrix (BCM) remains the predominant form and coexists with e-DOM. However, the combined effects of BCM and e-DOM on microbial Cr(VI) removal are unclear. This study investigated the individual and combined impacts of biochar matrix and AQDS (a model e-DOM) on Cr(VI) reduction by S. oneidensis MR-1. Results showed that biochar matrix or AQDS alone promoted Cr(VI) removal, primarily by accelerating electron transfer during the fast reduction phase. However, when both were added, an antagonistic effect was observed, attributed to increased repulsive forces between the biochar matrix-AQDS complex and the bacterial cells, which inhibited electron transfer to Cr(VI). This research elucidates the electrochemical interactions between biochar matrix and e-DOM, providing a theoretical basis for biochar applications in environmental remediation and risk assessment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3975-2
The instability of oxygen redox activity in layered oxide cathodes, particularly the formation of localized electron holes on oxygen (O−) and subsequent anion dimerization, has been demonstrated to trigger rapid capacity degradation and severe voltage hysteresis. Our study primarily focuses on P3-type Na2/3Cu1/3Mn2/3O2, which demonstrates reversible oxygen redox with an exceptionally low voltage hysteresis of 0.05 V. Spectroscopic analyses demonstrate a reversible O2−→O− evolution in Na2/3Cu1/3Mn2/3O2 without O–O dimerization. Furthermore, Multilateral non-invasive magnetic methods reveal that strong Cu-O-Mn superexchange interactions during the metal-ligand redox process lead to delocalization of O− species and inhibition of irreversible O–O bonding, thereby enabling ultralow voltage hysteresis. This work establishes magnetic exchange engineering as a transformative strategy to unlock reversible oxygen redox in high-energy battery electrodes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512015
The co-contamination of cadmium (Cd), lead (Pb), and zinc (Zn) in agricultural soils near mining areas poses significant risks to ecosystems and human health. Conventional stabilization materials often exhibit insufficient performance for Zn, particularly in multi-metal systems. This study synthesized a novel composite biochar (PFMBC) by loading phosphate and iron-manganese oxides onto biochar via phosphoric acid impregnation followed by secondary pyrolysis at 600 °C. The stabilization efficiency of PFMBC was evaluated against pristine biochar (BC) and iron-manganese modified biochar (FMBC) in a soil collected from a lead-zinc mining area (total Cd: 43.77 mg·kg−1, Pb: 3355.94 mg·kg−1, Zn: 1296.57 mg·kg−1). After 60 days of incubation with 5% PFMBC, the DTPA-extractable (bioavailable) fractions of Cd, Pb, and Zn decreased by 73.44%, 90.10%, and 69.33%, respectively, significantly outperforming BC and FMBC. Sequential extraction indicated that PFMBC promoted the transformation of Cd, Pb, and Zn from acid-soluble and reducible fractions to more stable residual fractions. Characterization via FTIR, SEM, and XRD revealed enhanced surface functional groups and the formation of stable mineral phases. The synergistic effects of phosphate precipitation, iron-manganese oxide adsorption, and surface complexation contributed to the superior stabilization, particularly overcoming the challenge of Zn immobilization. These findings demonstrate that PFMBC is a promising amendment for the remediation of Cd-Pb-Zn co-contaminated soils, offering high efficiency and long-term stability.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608013
Eutrophication and cyanobacterial blooms threaten aquatic ecosystems and drinking water safety globally. This study evaluated the efficacy of a compound algicide (PQGA-126, PAC, and red soil) combined with submerged plants (Vallisneria natans and Hydrilla verticillata) for suppressing blooms and restoring eutrophic water. Indoor static experiments used algae-laden water from Nanhu Lake, Gongqingcheng, Jiangxi. Six treatments were established: control, V. natans alone, H. verticillata alone, algicide alone, algicide + V. natans, and algicide + H. verticillata. Results demonstrated that combined treatments significantly reduced total nitrogen (TN), total phosphorus (TP), chlorophyll-a (Chl-a), and turbidity, markedly lowering eutrophication within a short period. The combined approach outperformed single-plant treatments, with algicide + V. natans achieving the greatest reduction in the comprehensive trophic state index. Additionally, the algicide significantly enhanced V. natans growth rate and H. verticillata catalase (CAT) activity, indicating species-specific physiological responses. These findings suggest that integrating compound algicide with submerged plants, particularly V. natans, offers a promising strategy for rapid and effective eutrophic water remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4063-2
Quantum dot light-emitting diodes (QLEDs) are emerging as a leader in next-generation display technology. In principle, the efficiency of QLEDs is highly reliant on the radiative recombination rate of injected electrons and holes in the QD emissive layer. Within a solitary light-emitting cycle, a pre-negative-charged QD bursts into a fleeting sparkle upon encountering a hole, much like a lighted piston within a roaring engine. More pistons bring higher horsepower. The challenge of achieving highly efficient QLED lies in how to increase the number of pre-negatively charged QDs. To address these limitations, we developed a ZnO@ZnMgO core-shell nanoparticle (NP)-based electron transport layer (ETL). This design synergistically combines the high conductivity of ZnO core and the low defect density of the ZnMgO shell. Measured by electron-excited transient absorption, the average electron population (<N_e>) in the emissive layer for ZnO@ZnMgO and ZnMgO-based QLEDs was 0.61 and 0.33 at 4 V, respectively, which greatly increases the carrier recombination efficiency. As a result, green QLEDs achieve a peak EQE of 30.66%, maximum luminance of 1,615,039.85 cd/m2, and a low turn-on voltage of approximately 2 V. The T95 operational lifetime exceeded 29,000 h at 1,000 cd/m2. Currently, all parameters are at the top level within the QLED region.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60662-7
Perovskite-type catalysts show promise for CO2 methanation, yet their low-temperature performance and mechanisms remain unclear. Here, a LaNiO3/CeO2 catalyst was synthesized via sol-gel and impregnation. In situ reduction decomposed the perovskite into highly dispersed Ni0 particles (average 12.6 nm) on CeO2, which provided abundant oxygen vacancies (Ce3+/(Ce3++Ce4+) = 9.2%) and weak/moderate basic sites. This synergy enhanced CO2 adsorption and activation. At 200–300 °C, the catalyst achieved ~100% CH4 selectivity and CO2 conversion up to 23.6% at 300 °C. Comparative studies with LaNiO3, LaCeNiO4, Ni/CeO2, and La-Ni/CeO2 revealed that the perovskite pre-structuration and in situ reduction optimize Ni dispersion and metal-support interactions, stabilizing Ni0 and tuning surface basicity and oxygen vacancies. This work provides a design strategy for efficient low-temperature CO2 methanation catalysts.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60717-7
Alkali lignin, a high-volume byproduct from pulp and paper manufacturing and biomass refining, is a promising feedstock for aromatic hydrocarbon production in liquid fuels due to its high energy density and abundant aromatic moieties. However, its highly cross-linked polymeric structure hinders efficient valorization. This work investigates catalytic conversion of alkali lignin into bio-oil under in situ H2 supply from formic acid. A series of Ni-Mo/h-BN bimetallic catalysts with varied metal ratios were synthesized by impregnation and characterized by XPS, XRD, and other techniques. The effects of reaction parameters on H2 production via aqueous-phase reforming (APR) of formic acid were evaluated. Optimal H2 yield was achieved at a formic acid-to-water molar ratio of 1:10 and a Ni/Mo atomic ratio of 3:1. H2 yield increased monotonically with temperature from 220 to 280 °C, reaching a maximum of 38.48 mmol. Subsequently, influences of reaction temperature and residence time on bio-oil production were examined. The highest heavy bio-oil yield (18.93%) and maximum relative content of aromatic hydrocarbons (13.81%) were both achieved at 280 °C. Prolonged reaction time reduced heavy bio-oil yield and aromatic hydrocarbon abundance while favoring furan derivatives. This work demonstrates good synergy between in situ hydrogen generation from formic acid and lignin hydrogenation in the temperature range 240–280 °C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4163-y
Liquid metals (LMs) are promising catalyst systems due to their unique interfacial properties, yet migration and aggregation of active species cause performance degradation. Here, we report a composition optimization strategy using a Ga-In eutectic liquid metal support to reduce surface energy and achieve homogeneous incorporation of Cu species (GaIn-Cu). Comprehensive characterizations confirm uniform Cu dispersion, which inhibits migration and formation of CuGa2 intermetallic phases during CO2 electroreduction (CO2RR). The GaIn-10-Cu catalyst achieves a maximum CH4 Faradaic efficiency of 73.49% at -0.8 V vs. RHE, significantly higher than Ga-Cu (61.49%). Moreover, GaIn-10-Cu exhibits enhanced stability for CH4 generation over 40 h of continuous operation. In-situ spectroscopic studies reveal that GaIn-10-Cu favors formation and protonation of key *CHO and *OCH3 intermediates, steering selectivity toward CH4. This work demonstrates that tuning LM composition modulates catalytic site performance, offering a strategy for durable and selective LM-based electrocatalysts.