SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4417-x
Balancing mechanical strength, corrosion resistance, and soft magnetic performance in structural-functional integrated materials remains a persistent metallurgical challenge. This study reports a face-centered cubic (FCC) Fe40Co35Ni15Al3Ta2Cr5 (at.%) high-entropy alloy (HEA) that achieves an unprecedented combination of these properties. The alloy exhibits a tensile strength of ~1200 MPa, total elongation of ~25%, saturation magnetization of 101.54 Am2·kg-1, and coercivity of 267.34 A·m-1. These values surpass most reported magnetic HEAs and conventional soft magnetic alloys. In a simulated 3.50 wt.% NaCl seawater environment, the alloy demonstrates a corrosion current density of 3.99 × 10-7 A·cm-2, comparable to 316L stainless steel. The synergy arises from nanoprecipitate engineering within the FCC matrix, which impedes dislocation motion while maintaining magnetic domain wall mobility and promoting a protective passive film. This work provides a design pathway for soft magnetic structural-functional materials suitable for corrosive marine environments, where simultaneous load-bearing and magnetic actuation are required.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3883-2
Tensile stress annealing (TSA) is an effective strategy for tailoring magnetic anisotropy and high-frequency performance in nanocrystalline soft magnetic alloys. Here, we systematically investigate the influence of TSA on the microstructure, magnetic domain evolution, and permeability stability of Fe69.5Co3Nb2Mo1.5Si14B9Cu1 nanocrystalline alloys. Across all applied stresses (0–300 MPa), the alloys retain an ultrafine grain size (≤11 nm), yet the induced uniaxial anisotropy constant (Ku) rises sharply from 22.5 to 665 J/m3. This increase in Ku refines the magnetic domain structure, reducing average domain width from 110 to 36 μm, and shifts the magnetization mechanism from domain-wall displacement to rotation-dominated reversal. Quantitative correlation between Ku, domain structure, and effective permeability (μe) reveals that higher stress suppresses μe at low frequencies but yields exceptional frequency stability: μe ≈ 2330 is maintained up to 1 MHz at 50 MPa, and μe ≈ 585 remains constant from 1 kHz to 10 MHz at 300 MPa. These findings demonstrate that stress-induced anisotropy is a decisive factor in governing high-frequency magnetic response, offering both mechanistic insight and a practical framework for designing next-generation soft magnetic materials for precision current transformers, EMC filters, and MHz-class power electronics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606005
In the context of carbon peaking and carbon neutrality, urban reclaimed water plants must adopt measures such as energy conservation, consumption reduction, and enhanced resource and energy utilization to achieve carbon neutrality. This study developed a carbon emission balance model and accounting method for such plants, incorporating strategies of carbon emission reduction, carbon substitution, and carbon sink. The optimal pathway towards carbon neutrality was evaluated based on the carbon emission balance ratio. Using a 1×10⁵ m³/d urban reclaimed water plant as a case study, the results showed total carbon emissions of 20,934 t CO2e. The carbon emission reduction from reclaimed water source heat pumps for heating and cooling was 21,701 t CO2e, yielding a carbon emission balance ratio of 103.7%. In contrast, other carbon reduction measures contributed 15,424 t CO2e, with a balance ratio of 73.7%, highlighting the pivotal role of reclaimed water source heat pumps. When the heat pump extracted 27% and 36% of residual thermal energy, coupled with reclaimed water reuse or sludge anaerobic digestion-cogeneration, respectively, both pathways achieved a 100% balance ratio. Assuming year-round extraction, the balance ratio reached 213%. The carbon reduction ratio between utilizing residual thermal energy and chemical energy was 8.76:1. This study demonstrates that urban reclaimed water plants can achieve carbon neutrality through multiple pathways, with residual thermal energy recovery exhibiting significant potential.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60684-6
Tungsten trioxide (WO3) is a transition metal oxide of significant interest in heterogeneous catalysis due to its environmental friendliness, cost-effectiveness, and favorable electrical properties. The catalytic performance of WO3 is strongly dependent on its exposed crystal facets, which exhibit distinct physicochemical properties including charge separation efficiency, reactant adsorption capacity, and redox activity. These differences arise from variations in atomic arrangement, electronic structure, and surface energy. This review systematically examines the facet effect of WO3 across photocatalysis, electrocatalysis, photoelectrocatalysis, and thermal catalysis. Theoretical calculations are integrated to elucidate the intrinsic mechanisms underlying facet-dependent behavior from an atomic structure perspective. The paper synthesizes general rules governing the WO3 facet effect across these applications, critically assesses current research limitations, and outlines future directions. Key findings highlight that facet engineering enables precise tuning of catalytic activity and selectivity, with specific facets such as {001}, {110}, and {010} demonstrating enhanced performance in various reactions. The review underscores the importance of morphology control in optimizing WO3-based catalysts and identifies challenges in achieving facet-selective synthesis and stability under operational conditions. Future research should focus on advanced characterization techniques and computational modeling to further unravel facet-dependent mechanisms and guide rational catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4067-4
Confined growth of metal halide perovskite quantum dots (QDs) in porous matrices yields improved stability and sensitivity for their implementation in luminescent chemical sensing applications. Here, we realized the synthesis of highly stable (water, photo, and thermal) and luminescent CsPbX3 QDs within nanoporous glass (NG). This is achieved by a nano-confined aqueous synthesis of CsPbBr3 QDs in Pb-anchored NG. Benefiting from strong Pb–O–Si chemical bonding between the perovskite QDs and the NG matrix, the stability of the encapsulated perovskite QDs is significantly enhanced. The emission of the perovskite NG can be tuned from 440 to 760 nm. By integrating green- and red-emitting perovskite NG onto a blue LED chip, stable WLEDs were successfully fabricated. This facile approach enables the integration of ultra-stable perovskite QDs within transparent porous monoliths toward diverse luminescent chemical sensing applications.