SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4281-7
Multispectral camouflage materials must simultaneously address visible and infrared (IR) detection while maintaining environmental stability and mechanical flexibility for deployment in harsh conditions. This work presents a multilayer composite integrating a colorful, IR-transparent visible reflection (VR) layer, a low-emissivity graphene (LEG) layer, and an aramid nanofiber (ANF) aerogel layer. The VR layer provides tunable visible colors without compromising the low-emissivity property of the LEG layer, which achieves IR emissivity between 0.30 and 0.43. The ANF aerogel, reinforced with a grid structure, reduces thermal conduction, lowering IR radiation intensity by 40% at an 80 °C heat source. The composite exhibits effective electromagnetic interference (EMI) shielding and maintains multifunctional stability in strong acid, strong alkali, saline, and organic media. This design offers a novel strategy for environmentally robust multispectral camouflage materials suitable for extreme operational environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0024
This study investigates the thermochemical conversion behavior of microalgae pellets in a molten hydroxide salt (80% NaOH-20% Na2CO3) system and its influence on hydrogen production. By comparing temperature evolution, gas release characteristics, and structural evolution of pellets with and without molten salt, and integrating char alkalization experiments, the regulatory mechanism of molten salt on reaction pathways and hydrogen production was systematically analyzed. Results indicate that molten salt significantly enhances internal heat transfer efficiency, achieving a central heating rate of 177 °C/s, effectively alleviating thermal hysteresis. Concurrently, molten salt promotes pore development through penetration, erosion, and catalytic effects, resulting in a porosity increase of 53.2%–104.3% after 10 s of reaction. Conversion efficiency is markedly improved, with the dominant reaction pathway shifting to char alkalization after only 70 s. Furthermore, when heating rate is increased above 600 °C, hydrogen yield from char alkalization improves more significantly, primarily attributed to the synergistic promotion of molten salt catalysis and rapid heating on volatiles reforming. This study provides a theoretical foundation for understanding efficient hydrogen production from biomass in molten hydroxide salts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604009
Biological nitrogen removal in wastewater treatment plants (WWTPs) is often limited by insufficient influent carbon sources, necessitating external carbon addition to enhance denitrification. Conventional single carbon sources, such as sodium acetate, frequently fail to meet the metabolic demands of complex microbial communities, compromising nitrogen removal efficiency and stability. Composite carbon sources, by providing multiple electron donors, can improve metabolic cooperation among microorganisms, yet their underlying microbial mechanisms remain insufficiently understood. In this study, activated sludge from a municipal WWTP was used to investigate the microbial mechanisms of composite carbon sources during denitrification. Batch denitrification experiments were conducted in combination with metagenomic and metatranscriptomic analyses to systematically characterize microbial community structure and functional gene expression under different carbon source conditions. Results showed that, compared with sodium acetate as the single carbon source, the composite carbon source system (sodium acetate: sodium succinate: ethanol = 2:1:3) increased the denitrification rate from (6.822 ± 0.141) mg/(L·h) to (8.370 ± 0.186) mg/(L·h), representing a 22.7% improvement, while reducing N2O accumulation by approximately 55%. Metagenomic analysis revealed that Ottowia, Rubrivivax, Thauera, and Zoogloea were the dominant denitrifying genera. Metatranscriptomic results further demonstrated that the composite carbon sources significantly upregulated the transcription of key denitrification genes, with nirS, norB, and nosZ increasing by 37.8%, 27.4%, and 48.6%, respectively. In addition, the composite carbon sources promoted complementary carbon metabolic strategies among different microbial communities, enhancing electron donor supply and improving denitrification efficiency. These findings indicate that composite carbon sources synergistically enhance denitrification performance through regulation of functional gene transcription in complex microbial communities, providing a theoretical basis for carbon source optimization in WWTPs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4043-3
In-plane InAs nanowires and nanowire networks are promising platforms for electronics, optoelectronics, and topological quantum computing due to their small electron effective mass, narrow bandgap, high electron mobility, strong spin-orbit coupling, and large Landé g factor. However, their selective area growth on CMOS-compatible group-IV substrates remains challenging. Here, we report the selective area growth of high-quality in-plane InAs nanowires and nanowire networks on Ge(111) substrates by molecular-beam epitaxy. Conventional selective-area epitaxy fails to simultaneously achieve good selectivity and continuity. To overcome this, we developed a metal-sown, single-indium-source two-step growth method, which attains both selectivity and continuity but yields nanowires with rough surfaces and lengths below 10 μm. We then introduced an upgraded metal-sown, dual-indium-source two-step growth method, successfully fabricating in-plane InAs nanowires and nanowire networks with smooth surface morphology and lengths exceeding 60 μm. By optimizing the As beam equivalent pressure, overgrowth at network junctions is effectively suppressed, resulting in uniform nanowire networks. High-resolution transmission electron microscopy and Raman spectroscopy confirm the high-quality single-crystalline nature and pure zinc-blende structure of the nanowires and networks. This work establishes a foundation for fabricating high-quality in-plane InAs/superconductor hybrid nanowires and nanowire networks on Ge substrates.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011303
Polybrominated diphenyl ethers (PBDEs) are persistent organic pollutants with environmental persistence, bioaccumulation, and toxicity, posing significant threats to marine ecosystems and human health. This study developed an analytical method using anhydrous sodium sulfate-alumina composite column chromatography coupled with gas chromatography-orbitrap mass spectrometry to quantify mono- to deca-BDEs in coastal seawater of Dalian, China. The total PBDE concentrations (∑PBDEs) ranged from not detected to 511.96 pg·L−1, with a mean of 163.96 pg·L−1. BDE-209 was the dominant congener, contributing 24.1% to ∑PBDEs. Spatial distribution exhibited distinct heterogeneity, with higher abundances of highly brominated PBDEs near sewage discharge outlets. Partial least squares discriminant analysis indicated that anthropogenic activities, particularly sewage discharge, were the primary sources. Ecological risk assessment revealed extremely low risk, with the highest risk quotient of 0.013 for BDE-17. These findings provide baseline data for PBDE contamination in Dalian coastal waters and underscore the need for continued monitoring of emerging contaminants.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030303
Emerging organic pollutants (EOPs) represent a class of toxic and hazardous chemicals characterized by ecotoxicity, environmental persistence, and bio-accumulation. Conventional water treatment processes have proven inadequate in eliminating these EOPs, leading to their accumulation in aquatic ecosystems and posing severe threats to the health and safety of aquatic organisms. Consequently, the development of efficient technologies for the complete elimination of EOPs from water matrix is of great importance. Recently, carbon nitride (CN)-based photocatalytic degradation technologies have been extensively utilized for the efficient treatment of organic pollutants in water environments due to their advantages of being green, efficient, and cost-effective. Furthermore, the catalytic activity of CN-based photocatalytic systems can be significantly improved and energy recovery can be achieved via coupling these systems with other advanced oxidation technologies. This review provides a critical review of the modification strategies for CN photocatalytic materials and their application in photocatalytic coupling systems toward EOPs elimination. Moreover, the opportunities and challenges on the photocatalytic coupling systems have been discussed.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606017
Against the backdrop of global green transition and tightening resource constraints, China's Dual Carbon Goals and Zero-Waste City initiative have positioned waste valorization as a critical pathway for sustainable development. Zinc, a fundamental metal, faces high external dependence and nearing primary resource limits, making the regenerated zinc industry essential. However, the previous standard YS/T 1093-2015 lagged in classification, technical indicators, and environmental requirements. This paper analyzes the revision to YS/T 1093-2024, which renames the standard to 'Recycled Zinc Raw Materials' and clarifies its role as front-end smelting intermediate feedstock. The new standard establishes a classification system covering six typical zinc-bearing materials, expanding utilization of low-grade complex materials (zinc content 5%-15%). It tightens limits on harmful elements (fluorine, chlorine, lead, arsenic) and introduces moisture control and appearance evaluation indicators, enhancing operability and environmental risk control. Compared with EU standards, it shows systematic improvements in raw material coverage, process adaptability, and environmental risk prevention. The revision is expected to drive the regenerated zinc industry toward intensification, high-value utilization, and clean production, improving resource recycling efficiency and supporting China's zinc resource strategic security and low-carbon development.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3365-5
Conventional oil-water separation technologies, including centrifugation and flocculation, suffer from density-dependent limitations and secondary pollution, while membrane filtration with uniform wettability selectively recovers only one phase, leaving retained components unrecovered. Janus membranes with asymmetric wettability enable on-demand separation but their micro/nanoscale thickness restricts interfacial separation to microscopic domains. This work presents a Janus-channel-membrane (JCM) architecture that scales asymmetric wettability from micro/nanoscale to millimeter-scale spatial channels, constructed from a hydrophilic membrane and a hydrophobic membrane separated by a slit of a few millimeters. When surfactant-stabilized emulsions are delivered to the slit, purified water permeates rapidly through the hydrophilic membrane while oil is concurrently recovered at the hydrophobic membrane. The millimeter-scale channel width enhances enrichment and collision behavior of emulsion droplets via interference interactions between the membrane pair, producing substantial increases in oil and water recovery rates. The JCM demonstrates distinctive advantages for separating and recovering both phases from high-concentration-surfactant-stabilized emulsions. Multistage device configurations incorporating JCMs can further strengthen separation and recovery efficiency at multiple levels, offering transformative potential for industrial emulsion separation and recovery. This spatial configuration of membranes with contrary wettability at the millimeter scale addresses key bottlenecks in concurrent oil and water recovery from stable emulsions.