SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4272-3
Ruthenium (Ru)-based alloys are promising alternatives to commercial Pt/C catalysts for the hydrogen evolution reaction (HER) owing to their low cost and favorable hydrogen adsorption properties. However, the sluggish water dissociation on Ru catalysts remains a major kinetic bottleneck in alkaline solutions. Herein, we report a rare earth (RE) dilute alloy strategy by incorporating a trace amount of cerium (Ce, ~1 at%) into a RuCu alloy to promote interfacial water activation. The oxophilic Ce sites strengthen H2O adsorption and reduce the energy barrier for water dissociation, thereby accelerating the Volmer step during alkaline hydrogen evolution. Consequently, the RuCuCe catalyst delivers 10 mA cm−2 at an overpotential of only 18 mV in 1.0 M KOH and maintains stable operation for over 100 h at 500 mA cm−2 in a membrane electrode assembly. In situ electrochemical impedance spectroscopy and pH-dependent measurements verify the facilitated Volmer process induced by Ce incorporation. Temperature-dependent analysis further shows that the apparent activation energy decreases from 47.4 kJ mol−1 for RuCu to 26.4 kJ mol−1 for RuCuCe, consistent with enhanced water dissociation kinetics. This work establishes RE dilute metal alloys as an effective platform for boosting the intrinsic activity of Ru-based alloy catalysts, in which RE incorporation promotes water dissociation while inducing charge redistribution in the alloy matrix.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61073-6
Elastomers are widely used in engineering but suffer degradation when exposed to heat, ozone, UV radiation, and chemicals. To enhance performance for specific industrial applications, blending with other materials is common. In this study, chloroprene rubber (CR) was blended with brominated butyl rubber (BIIR) and reinforced with Ketjenblack (KB) at concentrations up to 20%. KB exhibits a porous, fluffy morphology with a high specific surface area of 1347 m²/g. Tensile tests were conducted before and after exposure to UV, ozone, saline, petrol, and diesel environments, and retention capacity was evaluated per ASTM standards. Transmission electron microscopy confirmed uniform dispersion of KB filler. Tribological and barrier property studies identified 10% KB as optimal due to uniform dispersion. Thermal degradation kinetics were analyzed using Kissinger–Akahira–Sunose modeling to determine activation energy. Dynamic mechanical analysis indicated a 5 °C reduction in glass transition temperature for the 20% composite. These elastomeric blends demonstrate potential as advanced materials for harsh industrial applications.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61098-0
Laser-assisted grown graphene electrodes are promising for electrochemical energy storage, but their performance is limited by poorly controlled pore networks. This study demonstrates that a simple thermal post-treatment effectively tunes porosity and surface chemistry, significantly enhancing capacitive performance. Systematic variation of annealing temperature, dwell time, and atmosphere (air vs. inert) revealed that mild annealing in air up to 500 °C reduces oxygen-containing functionalities and increases the sp2/sp3 carbon ratio. Critically, specific surface area increased from 110 to 498 m² g⁻¹, with a broader pore-size distribution. These structural and chemical changes correlate with an almost order-of-magnitude increase in capacitance compared to untreated electrodes. The optimal condition—400 °C in air for 6 h—yielded electrodes retaining 92% of capacitance at a 25-fold current increase and 99% capacitance retention after 10,000 cycles. Density functional theory (DFT) simulations support a buckling–unknotting mechanism, where metastable interlayer sp3 or C–O–C linkages relax into lower-energy, untied bilayer configurations, reopening pores. This laser-based fabrication combined with thermal annealing offers a scalable, chemical-free route to high-performance graphene electrodes, avoiding wet-chemical activation. The established structure–property relationships provide clear guidance for optimizing related porous carbon architectures.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509035
Aerobic granular sludge (AGS) is an economical and efficient technology, yet its application has been largely confined to sequencing batch reactors (SBRs). This study introduces a novel continuous-flow self-circulating upflow granular sludge bed (Zier) process with separate aeration for treating real domestic wastewater. By regulating operational parameters, the nitrogen removal performance and granular sludge stability were investigated. Under hydraulic retention time of 10 h, self-circulation times of 29–58, and upflow velocity of 11–18 m·h−1, effluent NH4+-N and TN averaged (5±3.4) mg·L−1 and (10±2.8) mg·L−1, respectively, with COD at (30±6.2) mg·L−1. The process maintained sludge stability: mixed liquor suspended solids increased from 5,080 to 6,650 mg·L−1, mean particle size was 209.6 μm, and sludge volume index (SVI) remained at 50–60 mL·g−1. Extracellular polymeric substances (EPS) increased from 26.05 to 68.27 mg·g−1, with proteins (PN) rising from 21.26 to 59.44 mg·g−1 and polysaccharides (PS) from 4.79 to 8.82 mg·g−1, elevating the PN/PS ratio from 4.4 to 6.7. These results confirm that the Zier process preserves granular structure and function in continuous flow. The process demonstrates robust nitrogen removal and offers a novel approach for continuous-flow AGS applications in real wastewater treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3869-7
Iontronic capacitive pressure sensors (ICPSs) are pivotal for wearable technology, yet their performance is constrained by an inherent trade-off between sensitivity and detection range. Here, we introduce a micro-electric double layer (micro-EDL) engineering strategy to overcome this limitation. This is realized through a nanocomposite dielectric where multi-walled carbon nanotubes (MWCNTs) form a percolated network, generating a dense array of pressure-responsive nano-capacitors. Synergistically integrating a hierarchical MoS2/NiCo-LDH electrode provides abundant pseudocapacitive interfaces. The resulting sensor exhibits an ultrahigh sensitivity of 67,095 kPa−1 at 1 kHz, a broad detection range up to 1.3 MPa, rapid response and recovery times of 4 ms and 5 ms, respectively, and outstanding durability exceeding 18,000 cycles. Practical validation demonstrates 100% classification accuracy in recognizing complex gestures and gait patterns, underscoring its real-world applicability. These findings establish micro-EDL engineering as a promising route for advancing next-generation iontronic devices, offering insights into their electrochemical mechanisms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3906-2
Achieving flexible polymer-based organic afterglow materials with color-tunable and stimulus-responsive capabilities is significant in diverse optoelectronic fields, especially in next-generation wearable full-color display applications, yet remains a great challenge. Here, we report polymer-based dual-mode afterglow systems that realize long-lived color-tunable afterglow with full-color gamut of blue, green, orange, red, and even white-light emissions with ultralong lifetimes up to 2.42 s. This unique performance is enabled by a universal strategy of dual-mode afterglow-assisted Förster resonance energy transfer (FRET) that utilizes seconds-long dual-mode afterglow materials as energy donors and permits efficient synchronous transfer of singlet and triplet excitons from energy donors to the fluorescent dye acceptors. More impressively, the dual-mode afterglow-assisted FRET efficiency reaches up to 99%, with the lifetime of the energy acceptor reaching 1.55 s. Associated with the abundant hydrogen-bonding interactions within the polymer system, the doped afterglow films exhibit water/thermal stimulus responsiveness and recyclability. Furthermore, these full-color dual-mode afterglow materials are employed for multicolor screen-printing, optical anti-counterfeiting, and high-level information encryption, demonstrating considerable application potential in advanced anti-counterfeiting technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3905-9
Heteroatom doping is a widely adopted strategy to enhance the electrocatalytic activity of transition metal compounds, yet the intrinsic role of dopants beyond conventional electronic effects remains unresolved. This study reveals a missed heteroatom-doping effect using a graphene-supported Co-doped FeS2 catalyst for the oxygen evolution reaction (OER). Comprehensive characterization and in situ Raman spectroscopy demonstrate that Co incorporation disrupts S–S bond symmetry and orbital matching within FeS2, generating abundant S2− species that accelerate surface reconstruction into active FeOOH under electrochemical conditions. After reconstruction, Co atoms remain integrated within the FeOOH lattice, upshifting its d-band center and optimizing oxygen intermediate adsorption, as confirmed by theoretical calculations. This dual functionality of Co dopants—facilitating rapid reconstruction in the pre-catalyst and modulating the electronic structure of the active phase—provides novel mechanistic insights into dopant-induced dynamic reconstruction for electrocatalysis. The findings challenge the conventional understanding of doping effects and offer a rational design principle for Fe-based OER electrocatalysts, potentially lowering overpotentials and improving stability for practical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4083-9
Metal additive manufacturing (AM) enables the fabrication of arbitrary three-dimensional structures with unprecedented design freedom. However, components must withstand extreme in-service conditions, including high temperatures, fatigue, and creep, necessitating materials with multifunctional properties. Metal matrix composites (MMCs), comprising reinforcing particles embedded in metallic matrices, offer promising solutions for such harsh environments. Nevertheless, the non-equilibrium nature of AM processes introduces complex phase diffusion, reactions, and melt flow dynamics, making microstructural design and production challenging. This review focuses on the fatigue and creep resistance of additively manufactured MMCs under in-service conditions, emphasizing how composite strategies influence these properties. The underlying mechanisms responsible for property enhancements via AM are interpreted and discussed. Key findings indicate that AM enables refined microstructures, improved particle dispersion, and the formation of in-situ reinforcing phases, which collectively enhance fatigue life and creep resistance. For instance, TiC-reinforced steels exhibit improved wear resistance after heat treatment, and boron-phosphorus interactions in Inconel 718 enhance creep properties. The review provides insights into future directions for developing AM MMCs for critical applications, highlighting the need for tailored microstructures and process optimization to achieve balanced mechanical performance.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.