SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3654-5
Hydrogen production by photosynthetic green algae is an efficient biological process that utilizes light energy to convert water and carbon dioxide into clean and renewable energy. In this paper, we constructed a hybrid system combining graphitic carbon nitride (g-C3N4) and Chlorella pyrenoidosa (Chlorella), in which g-C3N4 serves as an extracellular electron source and Chlorella acts as a biological reactor for specific hydrogen production. In particular, the electronic structure of carbon nitride was optimized by means of hydrothermal alkalization and copper ion doping, expanded the light absorption range and enhanced the light response ability. g-C3N4, as an extracellular electron source, can provide electrons for Chlorella to improve hydrogen production performance which is 3.7 times that of bare Chlorella. The construction of a biological hybrid system is a feasible optimization strategy for the hybrid system to promote the synergistic effect of the hybrid system by regulating the properties of non-living components.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024083002
Selenium (Se) is an essential trace element for human health, and dietary intake through Se-rich crops is the primary route. However, total soil Se content does not directly reflect the bioavailability to plants, which depends largely on soil available Se. This study, conducted in Shipai Town, Longshan County, Hunan Province, used 1:50,000 land quality geochemical survey data to investigate factors influencing the Se bioaccumulation coefficient in maize kernels. Soil pH, CaO, and MgO were identified as significantly positively correlated with the bioaccumulation coefficient and were selected as proxies for soil available Se. A random forest (RF) model was developed to predict maize grain Se content and assess the feasibility of cultivating Se-rich maize in low-Se farmland. Results showed that although soil Se was deficient, 53.64% of maize grain samples met the Se-rich product standard (0.02–0.30 mg·kg−1). Compared with multiple linear regression, the RF model exhibited higher accuracy and reliability. The RF model predicted that 40.91% of farmland in the study area is suitable for natural Se-rich maize cultivation, representing a 25.86% increase over the area identified by soil total Se alone. This study provides a novel methodological framework for planting natural Se-rich maize in Se-deficient regions, validating the potential for such cultivation.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605001
The lower reaches of the Yangtze River Basin, as a concentrated area of China's C5 petroleum resin industry, face critical bottlenecks in green and low-carbon transformation due to high-pollution, refractory wastewater and high carbon emissions. Traditional petrochemical wastewater treatment technologies suffer from low efficiency, high energy consumption, and insufficient resource utilization. This paper systematically analyzes the sources of wastewater in C5 petroleum resin production from principles and processes, and reviews research progress and carbon reduction potential of current technologies in three aspects: new materials, new equipment, and new processes. Integrated processes centered on efficient pretreatment, biological enhancement, and multi-technology coupling show significant advantages in improving treatment efficiency, reducing energy consumption and cost, and strengthening resource recovery. The study also prospects future research priorities for pollution and carbon mitigation through green technological innovation and intelligent upgrading, providing new solutions for 'near-zero discharge' and resource recycling of C5 petroleum resin wastewater, thereby promoting the green and low-carbon transformation of the petrochemical industry.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042203
Cadmium (Cd) accumulation in crops is influenced by complex, crop-specific factors, posing challenges for the safe utilization of soils with elevated Cd levels. This study focused on a region with anomalously high soil Cd in northern Longshan County, Hunan Province, China. We systematically collected and analyzed Cd concentrations in the edible parts of lily (Lilium spp.) and maize (Zea mays L.), along with corresponding root-zone soil properties including Cd content, pH, and oxide levels. The bioconcentration factors (BCF-Cd) for lily and maize were compared, and their controlling factors were identified. Using random forest with hyperparameter optimization, optimal predictive models for BCF-Cd were developed for each crop. Results showed that lily BCF-Cd was significantly higher than that of maize. Key factors influencing BCF-Cd in both crops included soil pH, manganese (Mn), organic matter (OM), and the weathering-leaching coefficient (ba). Feature importance analysis identified soil pH as the most critical factor. Based on model predictions, a zoning scheme for safe arable land utilization was proposed to maximize land productivity while ensuring the medicinal safety of lily and food safety of maize. This study provides scientific support for enhancing food security and optimizing land resource use.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3843-9
Lignocellulose-based electromagnetic interference (EMI) shielding materials are gaining prominence across multiple sectors, driven by the growing EMI issues associated with rapid advances in communication technologies and electronic devices. These materials have demonstrated significant superiority over traditional EMI shielding solutions, which are often hampered by high cost and environmental concerns. This review emphasizes the excellent potential of lignocellulose as a cost-effective and flexible alternative to deliver the hierarchical structures and functional properties that qualify it for EMI shielding applications. The underlying EMI shielding mechanisms are then elucidated, with a focus on the benefits conferred by lignocellulose in such material systems. Furthermore, typical fabrication strategies for lignocellulose-based EMI shielding materials are comprehensively summarized, along with a discussion of their emerging applications in diverse scenarios. Finally, the challenges encountered in developing lignocellulose-based EMI shielding materials and their significant prospects for future boosting high-performance design and application are also outlined. The insights presented herein are expected to promote the development of efficient and green lignocellulose-based EMI shielding materials that meet the evolving demands of modern society.